Download or read book Time interleaved Analog to Digital Converters written by Simon Louwsma and published by Springer. This book was released on 2014-12-13 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Time-interleaved Analog-to-Digital Converters describes the research performed on low-power time-interleaved ADCs. A detailed theoretical analysis is made of the time-interleaved Track & Hold, since it must be capable of handling signals in the GHz range with little distortion, and minimal power consumption. Timing calibration is not attractive, therefore design techniques are presented which do not require timing calibration. The design of power efficient sub-ADCs is addressed with a theoretical analysis of a successive approximation converter and a pipeline converter. It turns out that the first can consume about 10 times less power than the latter, and this conclusion is supported by literature. Time-interleaved Analog-to-Digital Converters describes the design of a high performance time-interleaved ADC, with much attention for practical design aspects, aiming at both industry and research. Measurements show best-inclass performance with a sample-rate of 1.8 GS/s, 7.9 ENOBs and a power efficiency of 1 pJ/conversion-step.
Download or read book Background Calibration of Time Interleaved Data Converters written by Manar El-Chammas and published by Springer Science & Business Media. This book was released on 2011-12-17 with total page 138 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes techniques for time-interleaving a number of analog-to-digital data converters to achieve demanding bandwidth requirements. Readers will benefit from the presentation of a low-power solution that can be used in actual products, while alleviating the time-varying signal artifacts that typically arise when implementing such a system architecture.
Download or read book Interleaving Concepts for Digital to Analog Converters written by Christian Schmidt and published by Springer. This book was released on 2019-07-19 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern complementary metal oxide semiconductor (CMOS) digital-to-analog converters (DACs) are limited in their bandwidth due to technological constraints. These limitations can be overcome by parallel DAC architectures, which are called interleaving concepts. Christian Schmidt analyzes the limitations and the potential of two innovative DAC interleaving concepts to provide the basis for a practical implementation: the analog multiplexing DAC (AMUX-DAC) and the frequency interleaving DAC (FI-DAC). He presents analytical and discrete-time models as a theoretical foundation and develops digital signal processing (DSP) algorithms to compensate the analog impairments. Further, he quantifies the impact of various limiting parameters with numerical simulations and verifies both concepts in laboratory experiments. About the Author: Christian Schmidt works at the Fraunhofer Heinrich-Hertz-Institute, Berlin, Germany, on innovative solutions for broadband signal generation in the field of optical communications. The studies for his dissertation were carried out at the Technische Universität Berlin and at the Fraunhofer Heinrich-Hertz-Institute, both Berlin, Germany.
Download or read book Time interleaved Analog to Digital Converters written by Simon Louwsma and published by Springer Science & Business Media. This book was released on 2010-09-08 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: Time-interleaved Analog-to-Digital Converters describes the research performed on low-power time-interleaved ADCs. A detailed theoretical analysis is made of the time-interleaved Track & Hold, since it must be capable of handling signals in the GHz range with little distortion, and minimal power consumption. Timing calibration is not attractive, therefore design techniques are presented which do not require timing calibration. The design of power efficient sub-ADCs is addressed with a theoretical analysis of a successive approximation converter and a pipeline converter. It turns out that the first can consume about 10 times less power than the latter, and this conclusion is supported by literature. Time-interleaved Analog-to-Digital Converters describes the design of a high performance time-interleaved ADC, with much attention for practical design aspects, aiming at both industry and research. Measurements show best-inclass performance with a sample-rate of 1.8 GS/s, 7.9 ENOBs and a power efficiency of 1 pJ/conversion-step.
Download or read book Advanced Data Converters written by Gabriele Manganaro and published by Cambridge University Press. This book was released on 2011-11-17 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: Need to get up to speed quickly on the latest advances in high performance data converters? Want help choosing the best architecture for your application? With everything you need to know about the key new converter architectures, this guide is for you. It presents basic principles, circuit and system design techniques and associated trade-offs, doing away with lengthy mathematical proofs and providing intuitive descriptions upfront. Everything from time-to-digital converters to comparator-based/zero-crossing ADCs is covered and each topic is introduced with a short summary of the essential basics. Practical examples describing actual chips, along with extensive comparison between architectural or circuit options, ease architecture selection and help you cut design time and engineering risk. Trade-offs, advantages and disadvantages of each option are put into perspective with a discussion of future trends, showing where this field is heading, what is driving it and what the most important unanswered questions are.
Download or read book High Speed Data Converters written by Ahmed M.A. Ali and published by IET. This book was released on 2016-08-03 with total page 463 pages. Available in PDF, EPUB and Kindle. Book excerpt: High Speed Data Converters covers high speed data converters from the perspective of a leading high speed ADC designer and architect, with a strong emphasis on high speed Nyquist A/D converters. For our purposes, the term "high speed" is defined as sampling rates that are greater than 10 MS/s. The book is intended for engineers and students who design, evaluate or use high speed data converters. A basic foundation in circuits, devices and signal processing is required. The book is meant to bridge the gap between analysis and design, theory and practice, circuits and systems. It covers basic analog circuits and digital signal processing algorithms. There is a healthy dose of theoretical analysis in this book, combined with the practical issues and intuitive perspectives. Topics covered include: * Introduction to high-speed data conversion * Performance Metrics * Data Converter Architectures * Sampling * Comparators * Amplifiers * Pipelined A/D Converters * Time-interleaved Converters * Digitally Assisted Converters * Evolution and Trends
Download or read book CMOS Data Converters for Communications written by Mikael Gustavsson and published by Springer Science & Business Media. This book was released on 2005-12-15 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: CMOS Data Converters for Communications distinguishes itself from other data converter books by emphasizing system-related aspects of the design and frequency-domain measures. It explains in detail how to derive data converter requirements for a given communication system (baseband, passband, and multi-carrier systems). The authors also review CMOS data converter architectures and discuss their suitability for communications. The rest of the book is dedicated to high-performance CMOS data converter architecture and circuit design. Pipelined ADCs, parallel ADCs with an improved passive sampling technique, and oversampling ADCs are the focus for ADC architectures, while current-steering DAC modeling and implementation are the focus for DAC architectures. The principles of the switched-current and the switched-capacitor techniques are reviewed and their applications to crucial functional blocks such as multiplying DACs and integrators are detailed. The book outlines the design of the basic building blocks such as operational amplifiers, comparators, and reference generators with emphasis on the practical aspects. To operate analog circuits at a reduced supply voltage, special circuit techniques are needed. Low-voltage techniques are also discussed in this book. CMOS Data Converters for Communications can be used as a reference book by analog circuit designers to understand the data converter requirements for communication applications. It can also be used by telecommunication system designers to understand the difficulties of certain performance requirements on data converters. It is also an excellent resource to prepare analog students for the new challenges ahead.
Download or read book Analog to Digital Conversion written by Marcel Pelgrom and published by Springer. This book was released on 2016-09-29 with total page 565 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook is appropriate for use in graduate-level curricula in analog-to-digital conversion, as well as for practicing engineers in need of a state-of-the-art reference on data converters. It discusses various analog-to-digital conversion principles, including sampling, quantization, reference generation, nyquist architectures and sigma-delta modulation. This book presents an overview of the state of the art in this field and focuses on issues of optimizing accuracy and speed, while reducing the power level. This new, third edition emphasizes novel calibration concepts, the specific requirements of new systems, the consequences of 22-nm technology and the need for a more statistical approach to accuracy. Pedagogical enhancements to this edition include additional, new exercises, solved examples to introduce all key, new concepts and warnings, remarks and hints, from a practitioner's perspective, wherever appropriate. Considerable background information and practical tips, from designing a PCB, to lay-out aspects, to trade-offs on system level, complement the discussion of basic principles, making this book a valuable reference for the experienced engineer.
Download or read book Generalized Low Voltage Circuit Techniques for Very High Speed Time Interleaved Analog to Digital Converters written by Sai-Weng Sin and published by Springer Science & Business Media. This book was released on 2010-09-29 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analog-to-Digital Converters (ADCs) play an important role in most modern signal processing and wireless communication systems where extensive signal manipulation is necessary to be performed by complicated digital signal processing (DSP) circuitry. This trend also creates the possibility of fabricating all functional blocks of a system in a single chip (System On Chip - SoC), with great reductions in cost, chip area and power consumption. However, this tendency places an increasing challenge, in terms of speed, resolution, power consumption, and noise performance, in the design of the front-end ADC which is usually the bottleneck of the whole system, especially under the unavoidable low supply-voltage imposed by technology scaling, as well as the requirement of battery operated portable devices. Generalized Low-Voltage Circuit Techniques for Very High-Speed Time-Interleaved Analog-to-Digital Converters will present new techniques tailored for low-voltage and high-speed Switched-Capacitor (SC) ADC with various design-specific considerations.
Download or read book Digital Converters for Image Sensors written by Kenton T. Veeder and published by . This book was released on 2015 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is intended for image sensor professionals and those interested in the boundary between sensor systems and analog and mixed-signal integrated circuit design. It provides in-depth tips and techniques necessary to understand and implement these two types of complex circuit systems together for a wide variety of architectures or trade off one against another. The tutorial begins with a brief introduction to the history and definition of a digital image sensor, as well as converter characteristics, before addressing DAC and ADC architectures. Later chapters cover pipeline ADC designs, digital correction, calibration, and testing according to IEEE standards.
Download or read book Data Conversion Handbook written by Walt Kester and published by Newnes. This book was released on 2005 with total page 977 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive new handbook is a one-stop engineering reference covering data converter fundamentals, techniques, and applications. Beginning with the basic theoretical elements necessary for a complete understanding of data converters, the book covers all the latest advances made in this changing field. Details are provided on the design of high-speec ADCs, high accuracy DACs and ADCs, sample-and-hold amplifiers, voltage sources and current reference,noise-shaping coding, sigma-delta converters, and much more.
Download or read book Data Converters written by Franco Maloberti and published by Springer Science & Business Media. This book was released on 2007-02-22 with total page 454 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the first graduate-level textbook presenting a comprehensive treatment of Data Converters. The advancement of digital electronics urged the availability of a still missing support for teaching and self-learning analog-digital interfaces at many levels: the specification, the conversion methods and architectures, the circuit design and the testing. This book, after the necessary study of the background theoretical elements, covers aspects and provide elements for a deep and comprehensive knowledge. The breath and the level of details of topics is enhanced by introductory material in each chapter and the use of many examples, most of them in the form of computer behavioral simulations. The examples and the end-of-chapter problems help in understanding and favor self-practice using tools that are effective for training and for design activity. Data Converters is a textbook that is also essential for engineering professionals as it was written for responding to a shortage of organically organized material on the topic. The book assumes a solid background in analog and digital circuits as well as a working knowledge of simulation tools for circuit and behavioral analysis. A background on statistical analysis is also helpful, though not strictly necessary. Coverage of all the basic elements essential for a clear understanding of sampling, quantization, noise in sampled-data systems and mathematical tools for sampled-data linear systems Comprehensive definition of the parameters used to specify data converters and necessary for understanding product data sheets Coverage of all the architectures used in Nyquist-rate data converters and detailed study of features, limits and design techniques Detailed study of oversampled and Sigma-Delta converters with simulation examples and use of spectra and histograms for a clear understanding of features and limit if the noise shaping Coverage of digital correction and calibration techniques for enhancing performances Use of theory and intuitive views to explain circuits and systems operation and limits Coverage of testing methods and description of the data processing used for testing and characterization Extensive use of Simulink and Matlab in examples and problem sets to assist reader comprehension and favor deeper study
Download or read book Digitally Assisted Pipeline ADCs written by Boris Murmann and published by Springer Science & Business Media. This book was released on 2007-05-08 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt: Digitally Assisted Pipeline ADCs: Theory and Implementation explores the opportunity to reduce ADC power dissipation by leveraging digital signal processing capabilities in fine line integrated circuit technology. The described digitally assisted pipelined ADC uses a statistics-based system identification technique as an enabling element to replace precision residue amplifiers with simple open-loop gain stages. The digital compensation of analog circuit distortion eliminates one key factor in the classical noise-speed-linearity constraint loop and thereby enables a significant power reduction. Digitally Assisted Pipeline ADCs: Theory and Implementation describes in detail the implementation and measurement results of a 12-bit, 75-MSample/sec proof-of-concept prototype. The Experimental converter achieves power savings greater than 60% over conventional implementations. Digitally Assisted Pipeline ADCs: Theory and Implementation will be of interest to researchers and professionals interested in advances of state-of-the-art in A/D conversion techniques.
Download or read book Signal Processing and Analysis of Electrical Circuit written by Adam Glowacz and published by MDPI. This book was released on 2020-03-13 with total page 604 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Special Issue with 35 published articles shows the significance of the topic “Signal Processing and Analysis of Electrical Circuit”. This topic has been gaining increasing attention in recent times. The presented articles can be categorized into four different areas: signal processing and analysis methods of electrical circuits; electrical measurement technology; applications of signal processing of electrical equipment; fault diagnosis of electrical circuits. It is a fact that the development of electrical systems, signal processing methods, and circuits has been accelerating. Electronics applications related to electrical circuits and signal processing methods have gained noticeable attention in recent times. The methods of signal processing and electrical circuits are widely used by engineers and scientists all over the world. The constituent papers represent a significant contribution to electronics and present applications that can be used in industry. Further improvements to the presented approaches are required for realizing their full potential.
Download or read book Continuous Time Sigma Delta A D Conversion written by Friedel Gerfers and published by Springer Science & Business Media. This book was released on 2006-02-27 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sigma-delta A/D converters are a key building block in wireless and multimedia applications. This comprehensive book deals with all relevant aspects arising during the analysis, design and simulation of the now widespread continuous-time implementations of sigma-delta modulators. The results of several years of research by the authors in the field of CT sigma-delta modulators are covered, including the analysis and modeling of different CT modulator architectures, CT/DT loop filter synthesis, a detailed error analysis of all components, and possible compensation/correction schemes for the non-ideal behavior in CT sigma-delta modulators. Guidance for obtaining low-power consumption and several practical implementations are also presented. It is shown that all the proposed new theories, architectures and possible correction techniques have been confirmed by measurements on discrete or integrated circuits. Quantitative results are also provided, thus enabling prediction of the resulting accuracy.
Download or read book Advances in Analog and RF IC Design for Wireless Communication Systems written by Gabriele Manganaro and published by Academic Press. This book was released on 2013-05-13 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Analog and RF IC Design for Wireless Communication Systems gives technical introductions to the latest and most significant topics in the area of circuit design of analog/RF ICs for wireless communication systems, emphasizing wireless infrastructure rather than handsets. The book ranges from very high performance circuits for complex wireless infrastructure systems to selected highly integrated systems for handsets and mobile devices. Coverage includes power amplifiers, low-noise amplifiers, modulators, analog-to-digital converters (ADCs) and digital-to-analog converters (DACs), and even single-chip radios. This book offers a quick grasp of emerging research topics in RF integrated circuit design and their potential applications, with brief introductions to key topics followed by references to specialist papers for further reading. All of the chapters, compiled by editors well known in their field, have been authored by renowned experts in the subject. Each includes a complete introduction, followed by the relevant most significant and recent results on the topic at hand. This book gives researchers in industry and universities a quick grasp of the most important developments in analog and RF integrated circuit design. - Emerging research topics in RF IC design and its potential application - Case studies and practical implementation examples - Covers fundamental building blocks of a cellular base station system and satellite infrastructure - Insights from the experts on the design and the technology trade-offs, the challenges and open questions they often face - References to specialist papers for further reading
Download or read book 100 Years of Superconductivity written by Horst Rogalla and published by Taylor & Francis. This book was released on 2011-11-11 with total page 866 pages. Available in PDF, EPUB and Kindle. Book excerpt: Even a hundred years after its discovery, superconductivity continues to bring us new surprises, from superconducting magnets used in MRI to quantum detectors in electronics. 100 Years of Superconductivity presents a comprehensive collection of topics on nearly all the subdisciplines of superconductivity. Tracing the historical developments in supe
