Download or read book Three dimensional Numerical Simulation of Film Cooling on a Turbine Blade Leading edge Model written by Douglas Stenger and published by . This book was released on 2009 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present study is a three-dimensional numerical investigation of the effectiveness of film cooling for a turbine blade leading-edge model with both a single and a three-hole cooling configuration. The model used has the same dimensions as those in the experimental investigation of Ou and Rivir (2006). It consists of a half cylinder with a flat after-body, and well represents the leading edge of a turbine blade. The single coolant hole is situated approximately at the spanwise center of the cylindrical model, and makes an angle of 21.5 degrees to the leading edge and 20 degrees to the spanwise direction. For the three-hole configuration, the center hole is positioned the same as the single hole in the single-hole configuration, with the adjacent holes located at a spanwise distance of 37.4 mm on either side of the center hole. Multi-block grids were generated using GridGen, and the flows were simulated using the flow solver Fluent. A highly clustered structured C-grid was developed around the leading edge of the model. The outer unstructured-grid domain represents the wind tunnel as used in the experimental study of Ou and Rivir (2006), and the leading-edge model is located at the center of the domain. Simulations were carried out for blowing ratios, M, ranging from 0.75 to 2.0. Turbulence was represented using the k-? shear-stress transport (SST) model, and the flow was assumed to have a free-stream turbulence intensity of 0.75%. Two types of boundary conditions were used to represent the blade wall: an adiabatic surface, and a conductive surface. The adiabatic-wall results over-predicted the film-cooling effectiveness in the far downstream region for low blowing ratios. Also, in the vicinity of the cooling hole, an increase in blowing ratio resulted in higher film cooling effectiveness than observed in the experiments. It should be noted that the steady RANS-based turbulence model used under-predicts the interaction between the coolant and mainstream flow near the cooling-pipe exit. The conductive-wall results show a much closer agreement with experimental data for film effectiveness as compared to the adiabatic-wall predictions. Simulations were also performed with higher values of turbulence intensity at the cooling-hole inlet, and these predicted the coolant-mainstream interaction and the film-cooling effectiveness more accurately. Finally, a novel concept of pulsing the coolant flow was implemented so as to achieve film-cooling effectiveness equivalent to that with constant cooling, but with reduced overall coolant air, thereby enhancing turbine efficiency. Pulsed cooling with pulsing frequency PF = 5 and 10Hz, and duty cycle DC = 50%, shows the greatest cooling effects. The three-hole cooling results indicate that the 49 mm spanwise distance used for computing the spanwise-averaged values for film-cooling effectiveness accounts for all of the film-coolant spreading provided by the single hole. Also, the neighboring cooling holes contribute little film cooling to the 49 mm spanwise distance. The most significant new finding in this work is that the inclusion of wall conductance is the main factor responsible for reproducing the experimental data.

Download or read book Numerical Simulation of a Film Cooled Turbine Blade Leading Edge Including Heat Transfer Effects written by Laurene D. Dobrowolski and published by . This book was released on 2009 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computations and experiments were run to study heat transfer and overall effectiveness for a simulated turbine blade leading edge. Computational predictions were run for a film cooled leading edge model using a conjugate numerical method to predict the normalized "metal" temperatures for the model. This computational study was done in conjunction with a parallel effort to experimentally determine normalized metal temperatures, i.e. overall effectiveness, using a specially designed high conductivity model. Predictions of overall effectiveness were higher than experimentally measured values in the stagnation region, but lower along the downstream section of the leading edge. Reasons for the differences between computational predictions and experimental measurements were examined. Also of interest was the validity of Taw as the driving temperature for heat transfer into the blade, and this was examined via computations. Overall, this assumption gave reasonable results except near the stagnation line. Experiments were also conducted on a leading edge with no film cooling to gain a better understanding of the additional cooling provided by film cooling. Heat flux was also measured and external and internal heat transfer coefficients were determined. The results showed roughly constant overall effectiveness on the external surface.

Download or read book Leading Edge Film Cooling Effects on Turbine Blade Heat Transfer written by Vijay K. Garg and published by . This book was released on 1995 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine and Aeroengine Congress and Exposition, Houston, Texas - June 5-8, 1995.

Download or read book A Numerical Study of the Effect of Wake Passing on Turbine Blade Film Cooling written by James D. Heidmann and published by . This book was released on 1995 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book 3 D Numerical Simulation of the Flow Through a Turbine Blade Cascade with Cooling Injection at the Leading Edge written by Dieter Bohn and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine and Aeroengine Congress &Exhibition Birmingham, UK - June 10-13, 1996.

Download or read book Computational Simulation and Analysis of Film Cooling for the Leading edge Model of a Turbine Blade written by and published by . This book was released on 2007 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: The application of interest is the cooling of turbine blades in large gas combustion engines where hot gases from the combustor cause thermal deterioration of the metal turbine blades. A thin-film of coolant flow buffers the hottest parts of the blade surface. Heat transfer on a bluff body and, subsequently, a single-hole cooling problem is solved numerically in two-dimensions. The flow is assumed to be incompressible, and the laminar, steady Navier-Stokes equations are used to obtain the flow solution. Results for the bluff-body heat transfer agree very well with experimental data up to the separation point, and are within 20% of the data thereafter. The film-cooling simulation yielded higher cooling effectiveness due in large part to the use of the two-dimensional model, which treats the hole as a slot with higher coolant mass. Results from the simulations indicate that the Cobalt flow solver is capable of solving complex heat transfer problems.

Download or read book A Numerical Analysis of Heat Transfer and Effectiveness on Film Cooled Turbine Blade Tip Models written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-15 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: A computational study has been performed to predict the distribution of convective heat transfer coefficient on a simulated blade tip with cooling holes. The purpose of the examination was to assess the ability of a three-dimensional Reynolds-averaged Navier-Stokes solver to predict the rate of tip heat transfer and the distribution of cooling effectiveness. To this end, the simulation of tip clearance flow with blowing of Kim and Metzger was used. The agreement of the computed effectiveness with the data was quite good. The agreement with the heat transfer coefficient was not as good but improved away from the cooling holes. Numerical flow visualization showed that the uniformity of wetting of the surface by the film cooling jet is helped by the reverse flow due to edge separation of the main flow. Ameri, A. A. and Rigby, D. L. Glenn Research Center NASA/CR-1999-209165, NAS 1.26:209165, E-11756

Download or read book Impingement Jet Cooling in Gas Turbines written by R.S. Amano and published by WIT Press. This book was released on 2014-05-28 with total page 253 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to the requirement for enhanced cooling technologies on modern gas turbine engines, advanced research and development has had to take place in field of thermal engineering. Among the gas turbine cooling technologies, impingement jet cooling is one of the most effective in terms of cooling effectiveness, manufacturability and cost. The chapters contained in this book describe research on state-of-the-art and advanced cooling technologies that have been developed, or that are being researched, with a variety of approaches from theoretical, experimental, and CFD studies. The authors of the chapters have been selected from some of the most active researchers and scientists on the subject. This is the first to book published on the topics of gas turbines and heat transfer to focus on impingement cooling alone.

Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.

Download or read book Numerical Simulations of Leading Edge Film Cooling Flows for Gas Tubine Airfoils written by Cheryl A. Martin and published by . This book was released on 1997 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Heat Transfer in Gas Turbines written by Bengt Sundén and published by Witpress. This book was released on 2001 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: This title presents and reflects current active research on various heat transfer topics and related phenomena in gas turbine systems. It begins with a general introduction to gas turbine heat transfer, before moving on to specific areas.

Download or read book Numerical simulation and aerothermal physics of leading edge film cooling ASME 98 GT 504 written by A. Chernobrovkin and published by . This book was released on 1998 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presented at the International Gas Turbine & Aeroengine Congress & Exhibition, Stockholm, Sweden, Jun 2-5, 1998.

Download or read book Numerical Simulation of Flow in Turbine Blade Film Cooling written by Saravanakanthan Rajendran and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Numerical simulation of film cooling for gas turbine blades written by Jason B. Blitz and published by . This book was released on 1992 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Gas Turbine Heat Transfer and Cooling Technology Second Edition written by Je-Chin Han and published by CRC Press. This book was released on 2012-11-27 with total page 892 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.

Download or read book Computational Methods and Experimental Measurements XV written by G. M. Carlomagno and published by WIT Press. This book was released on 2011 with total page 737 pages. Available in PDF, EPUB and Kindle. Book excerpt: Containing edited versions of most of the papers presented at the Fifteenth International Conference on Computational Methods and Experimental Measurements, this book reviews the latest work on these two approaches, and the interaction between them.

Download or read book Development of a suitable turbulence and heat transfer model for a 3D calculation procedure for film cooling of turbine blade leading edges written by W. Rodi and published by . This book was released on 1997 with total page 183 pages. Available in PDF, EPUB and Kindle. Book excerpt: