Download or read book Third Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1965 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fourth Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1965 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sixth Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1966 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fifth Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1966 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Seventh Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1967 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Second Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1964 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Eight Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1967 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Ninth Status Report of the U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1968 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Index to DMIC Reports and Memoranda written by Battelle Memorial Institute. Defense Metals Information Center and published by . This book was released on 1968 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Metal Deformation Processing written by F. W. Boulger and published by . This book was released on 1967 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Metalworking Processes and Equipment Program, information was collected on deformation characteristics of metals and their effect on processing operations. The report presents the information collected from technical engineering reports on Government contracts and from general engineering and metallurgical publications. The objective is to help the nonspecialist in recognizing the implications of scientific findings and in applying them in specific operations. This report contains a series of articles covering the following subjects: Ductile Fracture; Application of High Pressure to the Forming of Brittle Metals; Superplasticity; Lubrication in Metal-Deformation Processes; Swaging; Adiabatic Conditions in Deformation Processing; Residual Stresses produced by Deformation. These subjects are treated in two ways: (1) generalized discussions of common processes point out why specific variables must be modified in order to deform certain types of metals satisfactorily; and (2) data on the more difficult-to-form metals are used to illustrate the principles, limitations, and effects of the processes. (Author).
Download or read book Fiber reinforced Metal matrix Composites written by Curtis Maitland Jackson and published by . This book was released on 1967 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: The introductory sections contain a brief discussion of the general methods of producing fiber-reinforced composites and of the theory of fiber-reinforcement of metals. The body of the report describes research on fiber-reinforced metal matrix composites, and is organized according to metal matrix materials. For convenience, the report is divided into two sections: Low density matrices (including aluminum, magnesium, and titanium and their alloys) and high density matrices (cobalt, copper and its alloys, iron, lead-tin alloys, nickel and nickel alloys, silver, tantalum, and tungsten). (Author).
Download or read book Forming of Titanium and Titanium Alloys written by D. E. Strohecker and published by . This book was released on 1967 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report represents a portion of the information contained in the March, 1967, revised edition of the 'Aircraft Designer's Handbook for Titanium and Titanium Alloys' which was prepared by the Defense Metals Information Center under the joint sponsorship of the U.S. Air Force Research and Technology Division, and the Federal Aviation Agency. The important techniques discussed include; (1) brake forming, (2) stretch forming, (3) deep drawing, (4) trapped-rubber forming, (5) tube bulging, (6) bending, (7) drop-hammer forming, (8) roll forming, (9) roll bending, (10) spinning, (11) shear forming, (12) dimpling, (13) joggling, and (14) hot sizing. Auxiliary metalworking operations, preparation for forming, blank heating methods, lubricants for forming and tooling materials are discussed. Other data available in the open literature have been summarized and referenced to present a comprehensive picture on the state of the art of these fabrication methods as related to titanium and its alloys. (Author).
Download or read book Explosive Bonding written by V. D. Linse and published by . This book was released on 1967 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describes basic mechanics of the process, practices of those in the field, metal combinations and configurations that have been bonded, and applications.
Download or read book Corrosion of Beryllium written by Paul D. Miller and published by . This book was released on 1967 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: The report summarizes the corrosion behavior of beryllium. The effects on beryllium of the following environments are considered: moisture, salt solutions, acids, alkalis, gases, organic liquids, molten materials, and solid materials. Stress-corrosion cracking and galvanic effects are also discussed. A final section of the report reviews various types of coatings for protection of beryllium from corrosion by a variety of environments.
Download or read book Powder Metallurgy of Beryllium written by Stanley W. Porembka and published by . This book was released on 1967 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report discusses the powder metallurgy of beryllium from the preparation of powders through the production from the powders of solid products. Various methods of powder compaction are presented including die pressing, isopressing, slip casting, vibration packing and explosive compaction. Sintering, and methods of elevated temperature consolidation, including vacuum hot pressing, hot isostatic pressing, forging, extrusion, and plasma spraying, are discussed. The final sections of the report cover properties of powder beryllium products, applications of beryllium prepared by powder metallurgy and current trends in the powder metallurgy of beryllium. (Author).
Download or read book Joining of Titanium written by Robert Edward Monroe and published by . This book was released on 1967 with total page 86 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report supplies information on joining processes applicable to titanium and its alloys in sheet metal applications, primarily related directly to airframe construction. Although the material presented here does not cover all titanium joining processes, and omits such processes as plasma-arc, submerged-arc, electroslag, flash, and high-frequency resistance welding, the data presented cover materials up to 2-inches thick in some cases and the report should be useful to anyone seeking titanium joining information. The joining processes covered fall into five categories: welding, brazing, metallurgical bonding (diffusion and deformation bonding), adhesive bonding, and mechanical fastening. The fusion welding processes that are discussed in detail include gas tungsten arc, gas metal arc, arc spot, and electron beam. The resistance processes give extended coverage are spot, roll spot, and seam welding. (Author).
Download or read book Summary of Contractor Results in Support of the Refractory Metals Sheet Rolling Program written by D. J. Maykuth and published by . This book was released on 1966 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes the achievements on fourteen programs that were conducted in support of the Metals Sheet Rolling Program. These included programs for developing practices to produce large sheets from two grades of unalloyed tungsten (via powder metallurgy and arc melting, respectively), as well as for the Mo-0.5Ti, Mo-0.5Ti-0.1Zr-0.03C (TZM), Cb-10W-1Zr-0.1C (D-43), Cb-10W-2.5Zr (Cb-752), and Ta-30Cb-7.5V alloys. In addition, pilot sheet-rolling programs were also carried out for the Cb-27Ta-10W-1Zr (FS-85), Cb-5Mo-5V-1Zr (B-66), Ta-7W-3Re (GE-473), and Ta-9.6W-2.4Hf-0.01C (T-222) compositions.