Download or read book Thermo Mechanical Modeling of Additive Manufacturing written by Michael Gouge and published by Butterworth-Heinemann. This book was released on 2017-08-03 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermo-mechanical Modeling of Additive Manufacturing provides the background, methodology and description of modeling techniques to enable the reader to perform their own accurate and reliable simulations of any additive process. Part I provides an in depth introduction to the fundamentals of additive manufacturing modeling, a description of adaptive mesh strategies, a thorough description of thermal losses and a discussion of residual stress and distortion. Part II applies the engineering fundamentals to direct energy deposition processes including laser cladding, LENS builds, large electron beam parts and an exploration of residual stress and deformation mitigation strategies. Part III concerns the thermo-mechanical modeling of powder bed processes with a description of the heat input model, classical thermo-mechanical modeling, and part scale modeling. The book serves as an essential reference for engineers and technicians in both industry and academia, performing both research and full-scale production. Additive manufacturing processes are revolutionizing production throughout industry. These technologies enable the cost-effective manufacture of small lot parts, rapid repair of damaged components and construction of previously impossible-to-produce geometries. However, the large thermal gradients inherent in these processes incur large residual stresses and mechanical distortion, which can push the finished component out of engineering tolerance. Costly trial-and-error methods are commonly used for failure mitigation. Finite element modeling provides a compelling alternative, allowing for the prediction of residual stresses and distortion, and thus a tool to investigate methods of failure mitigation prior to building. - Provides understanding of important components in the finite element modeling of additive manufacturing processes necessary to obtain accurate results - Offers a deeper understanding of how the thermal gradients inherent in additive manufacturing induce distortion and residual stresses, and how to mitigate these undesirable phenomena - Includes a set of strategies for the modeler to improve computational efficiency when simulating various additive manufacturing processes - Serves as an essential reference for engineers and technicians in both industry and academia

Download or read book Computational Welding Mechanics written by John A. Goldak and published by Springer Science & Business Media. This book was released on 2006-07-04 with total page 326 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computational Welding Mechanics (CWM) provides readers with a complete introduction to the principles and applications of computational welding including coverage of the methods engineers and designers are using in computational welding mechanics to predict distortion and residual stress in welded structures, thereby creating safer, more reliable and lower cost structures. Drawing upon years of practical experience and the study of computational welding mechanics the authors instruct the reader how to: - understand and interpret computer simulation and virtual welding techniques including an in depth analysis of heat flow during welding, microstructure evolution and distortion analysis and fracture of welded structures, - relate CWM to the processes of design, build, inspect, regulate, operate and maintain welded structures, - apply computational welding mechanics to industries such as ship building, natural gas and automobile manufacturing. Ideally suited for practicing engineers and engineering students, Computational Welding Mechanics is a must-have book for understanding welded structures and recent technological advances in welding, and it provides a unified summary of recent research results contributed by other researchers.

Download or read book Recommended Values of Thermophysical Properties for Selected Commercial Alloys written by K. C. Mills and published by Woodhead Publishing. This book was released on 2002 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Additive Manufacturing with Metals written by Sanjay Joshi and published by Springer Nature. This book was released on 2023-12-29 with total page 669 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook and reference provides a comprehensive treatment of additive manufacturing (AM) for metals, including design and digital work flows, process science and reliability, metallic systems, quality assurance, and applications. The book is rooted in the fundamental science necessary to develop and understand AM technologies, as well as the application of engineering principles covering several disciplines to successfully exploit this important technology. As additive manufacturing of metals is the fastest growing subset of this transformative technology, with the potential to make the widest impact to industrial production, Metals Additive Manufacturing: Design, Processes, Materials, Quality Assurance, and Applications is ideal for students in a range of engineering disciplines and practitioners working in aerospace, automotive, medical device manufacturing industries.

Download or read book Predictive Theoretical and Computational Approaches for Additive Manufacturing written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2016-12-21 with total page 149 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) methods have great potential for promoting transformative research in many fields across the vast spectrum of engineering and materials science. AM is one of the leading forms of advanced manufacturing which enables direct computer-aided design (CAD) to part production without part-specific tooling. In October 2015 the National Academies of Sciences, Engineering, and Medicine convened a workshop of experts from diverse communities to examine predictive theoretical and computational approaches for various AM technologies. While experimental workshops in AM have been held in the past, this workshop uniquely focused on theoretical and computational approaches and involved areas such as simulation-based engineering and science, integrated computational materials engineering, mechanics, materials science, manufacturing processes, and other specialized areas. This publication summarizes the presentations and discussions from the workshop.

Download or read book Residual Stress Distributions in Additively Manufactured Parts written by Prabhat Pant and published by Linköping University Electronic Press. This book was released on 2020-03-05 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) of parts using a layer by layer approach has seen a rapid increase in application for production of net shape or near-net shape complex parts, especially in the field of aerospace, automotive, etc. Due to the superiority of manufacturing complex shapes with ease in comparison to the conventional methods, interest in these kinds of processes has increased. Among various methods in AM, laser powder bed fusion (LPBF) is one of the most widely used techniques to produce metallic components. As in all manufacturing processes, residual stress (RS) generation during manufacturing is a relevant issue for the AM process. RS in AM are generated due to a high thermal gradient between subsequent layers. The impact of residual stresses can be significant for the mechanical integrity of the built parts and understanding the generation of RS and the effect of AM process parameters is therefore important for a broader implementation of AM techniques. The work presented in this licentiate thesis aims to investigate the influence of build orientation on the RS distribution in AM parts. For this purpose, L-shaped Inconel 718 parts were printed by LPBF in three different orientations, 0°, 45°, and 90°, respectively. Inconel 718 was selected because it is a superalloy widely used for making gas turbine components. In addition, IN718 has in general good weldability which renders it a good material for additive manufacturing. Residual stress distributions in the parts removed from the build plate were measured using neutron diffraction technique. A simple finite element model was developed to predict the residual stresses and the effect of RS relaxation due to the separation of the parts and build plate. The trend of residual stress distribution predicted was in good agreement with experimental results. In general, compressive RS at the part center and tensile RS near the surface were found. However, while the part printed in 0° orientation had the least amount of RS in all three principal directions of part, the part built in 90° orientation possessed the highest amount of RS in both compression and tension. The study has shown that residual stress distributions in the parts are strongly dependent on the building process. Further, it has shown that the relaxation of RS associated with the removal of the parts from the build plate after printing has a great impact on the final distribution of residual stress in the parts. These results can be used as guidelines for choosing the orientations of the part during printing.

Download or read book ASM Metals Reference Book 3rd Edition written by Michael Bauccio and published by ASM International. This book was released on 1993-01-01 with total page 628 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference book makes it easy for anyone involved in materials selection, or in the design and manufacture of metallic structural components to quickly screen materials for a particular application. Information on practically all ferrous and nonferrous metals including powder metals is presented in tabular form for easy review and comparison between different materials. Included are chemical compositions, physical and mechanical properties, manufacturing processes, applications, pertinent specifications and standards, and test methods. Contents Overview: Glossary of metallurgical terms Selection of structural materials (specifications and standards, life cycle and failure modes, materials properties and design, and properties and applications) Physical data on the elements and alloys Testing and inspection Chemical composition and processing characteristics

Download or read book Multiscale Modeling of Additively Manufactured Metals written by Yi Zhang and published by Elsevier. This book was released on 2020-06-29 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: Multiscale Modeling of Additively Manufactured Metals: Application to Laser Powder Bed Fusion Process provides comprehensive coverage on the latest methodology in additive manufacturing (AM) modeling and simulation. Although there are extensive advances within the AM field, challenges to predictive theoretical and computational approaches still hinder the widespread adoption of AM. The book reviews metal additive materials and processes and discusses multiscale/multiphysics modeling strategies. In addition, coverage of modeling and simulation of AM process in order to understand the process-structure-property relationship is reviewed, along with the modeling of morphology evolution, phase transformation, and defect formation in AM parts. Residual stress, distortion, plasticity/damage in AM parts are also considered, with scales associated with the spatial, temporal and/or material domains reviewed. This book is useful for graduate students, engineers and professionals working on AM materials, equipment, process, development and modeling. - Includes the fundamental principles of additive manufacturing modeling techniques - Presents various modeling tools/software for AM modeling - Discusses various design methods and how to optimize the AM process using these models

Download or read book Heat Transfer in Polymer Composite Materials written by Nicolas Boyard and published by John Wiley & Sons. This book was released on 2016-03-28 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses general information, good practices and examples about thermo-physical properties, thermo-kinetic and thermo-mechanical couplings, instrumentation in thermal science, thermal optimization and infrared radiation.

Download or read book Impact of Scientific Computing on Science and Society written by Pekka Neittaanmäki and published by Springer Nature. This book was released on 2023-07-07 with total page 451 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book analyzes the impact of scientific computing in science and society over the coming decades. It presents advanced methods that can provide new possibilities to solve scientific problems and study important phenomena in society. The chapters cover Scientific computing as the third paradigm of science as well as the impact of scientific computing on natural sciences, environmental science, economics, social science, humanistic science, medicine, and engineering. Moreover, the book investigates scientific computing in high performance computing, quantum computing, and artificial intelligence environment and what it will be like in the 2030s and 2040s.

Download or read book Additive Manufacturing of Metals The Technology Materials Design and Production written by Li Yang and published by Springer. This book was released on 2017-05-11 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers a unique guide to the three-dimensional (3D) printing of metals. It covers various aspects of additive, subtractive, and joining processes used to form three-dimensional parts with applications ranging from prototyping to production. Examining a variety of manufacturing technologies and their ability to produce both prototypes and functional production-quality parts, the individual chapters address metal components and discuss some of the important research challenges associated with the use of these technologies. As well as exploring the latest technologies currently under development, the book features unique sections on electron beam melting technology, material lifting, and the importance this science has in the engineering context. Presenting unique real-life case studies from industry, this book is also the first to offer the perspective of engineers who work in the field of aerospace and transportation systems, and who design components and manufacturing networks. Written by the leading experts in this field at universities and in industry, it provides a comprehensive textbook for students and an invaluable guide for practitioners

Download or read book Computational Welding Mechanics written by Lars-Erik Lindgren and published by Elsevier. This book was released on 2014-01-23 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt: Computational welding mechanics (CWM) provides an important technique for modelling welding processes. Welding simulations are a key tool in improving the design and control of welding processes and the performance of welded components or structures. CWM can be used to model phenomena such as heat generation, thermal stresses and large plastic deformations of components or structures. It also has a wider application in modelling thermomechanical and microstructural phenomena in metals. This important book reviews the principles, methods and applications of CWM.The book begins by discussing the physics of welding before going on to review modelling methods and options as well as validation techniques. It also reviews applications in areas such as fatigue, buckling and deformation, improved service life of components and process optimisation. Some of the numerical methods described in the book are illustrated using software available from the author which allows readers to explore CWM in more depth.Computational welding mechanics is a standard work for welding engineers and all those researching welding processes and wider thermomechanical and microstructural phenomena in metals. - Highlights the principles, methods and applications of CWM - Discusses the physics of welding - Assesses modelling methods and validation techniques

Download or read book Laser Cladding written by Ehsan Toyserkani and published by CRC Press. This book was released on 2004-08-12 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: Capitalizing on the rapid growth and reduced costs of laser systems, laser cladding is gaining momentum, and in some instances replacing conventional techniques of depositing thin films because it can accommodate a great variety of materials, achieve uniform thickness and precise widths of layers, and provide improved resistance to wear and corrosion in the final product. Laser cladding technology also offers a revolutionary layered manufacturing and prototyping technique that can fabricate complex components without intermediate steps. Laser Cladding reviews the parameters, techniques and equipment, process modeling and control, and the physical metallurgy of alloying and solidification during laser cladding. The authors clarify the interconnections laser cladding has with CAD/CAM design; automation and robotics; sensors, feedback, and control; physics, material science, heat transfer, fluid dynamics, and powder metallurgy to promote further development and improved process quality of this growing technology. As the first book entirely dedicated to the topic, it also offers a history of its development and a guide to applications and market opportunities. While a considerable part of Laser Cladding is dedicated to industrial applications, this volume brings together valuable information illustrated with real case studies based on the authors' vast experience, and research and analysis in the field to provide a timely source for both academia and industry.

Download or read book Minimization of Welding Distortion and Buckling written by Pan Michaleris and published by Elsevier. This book was released on 2011-05-25 with total page 319 pages. Available in PDF, EPUB and Kindle. Book excerpt: Welding is a cost-effective and flexible method of fabricating large structures, but drawbacks such as residual stress, distortion and buckling must be overcome in order to optimize structural performance. Minimization of welding distortion and buckling provides a systematic overview of the methods of minimizing distortion and buckling in welded structures.Following an introductory chapter, part one focuses on understanding welding stress and distortion, with chapters on such topics as computational welding mechanics, modelling the effect of phase transformations on welding stress and distortion and using computationally efficient reduced-solution methods to understand welding distortion. Part two covers different methods of minimizing welding distortion. Chapters discuss methods such as differential heating for minimizing distortion in welded stiffeners, dynamic thermal tensioning, reverse-side heating and ways of minimizing buckling such as weld cooling and hybrid laser arc welding.With its distinguished editor and international team of contributors, Minimization of welding distortion and buckling is an essential reference for all welders and engineers involved in fabrication of metal end-products, as well as those in industry and academia with a research interest in the area. - Provides a systematic overview of the methods of minimizing distortion and buckling in welded structures - Focuses on understanding welding stress and distortion featuring computational welding mechanics and modelling the effect of phase transformations - Explores different methods of minimizing welding distortion discussing differential heating and dynamic thermal tensioning

Download or read book 3D Printing and Additive Manufacturing Technologies written by L. Jyothish Kumar and published by Springer. This book was released on 2018-06-07 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a selection of papers on advanced technologies for 3D printing and additive manufacturing, and demonstrates how these technologies have changed the face of direct, digital technologies for the rapid production of models, prototypes and patterns. Because of their wide range of applications, 3D printing and additive manufacturing technologies have sparked a powerful new industrial revolution in the field of manufacturing. The evolution of 3D printing and additive manufacturing technologies has changed design, engineering and manufacturing processes across such diverse industries as consumer products, aerospace, medical devices and automotive engineering. This book will help designers, R&D personnel, and practicing engineers grasp the latest developments in the field of 3D Printing and Additive Manufacturing.

Download or read book Additive Manufacturing for the Aerospace Industry written by Francis H. Froes and published by Elsevier. This book was released on 2019-02-15 with total page 483 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive Manufacturing for the Aerospace Industry explores the design, processing, metallurgy and applications of additive manufacturing (AM) within the aerospace industry. The book's editors have assembled an international team of experts who discuss recent developments and the future prospects of additive manufacturing. The work includes a review of the advantages of AM over conventionally subtractive fabrication, including cost considerations. Microstructures and mechanical properties are also presented, along with examples of components fabricated by AM. Readers will find information on a broad range of materials and processes used in additive manufacturing. It is ideal reading for those in academia, government labs, component fabricators, and research institutes, but will also appeal to all sectors of the aerospace industry. - Provides information on a broad range of materials and processes used in additive manufacturing - Presents recent developments in the design and applications of additive manufacturing specific to the aerospace industry - Covers a wide array of materials for use in the additive manufacturing of aerospace parts - Discusses current standards in the area of aerospace AM parts

Download or read book Additive Manufacturing Volume 2 written by Prashanth Konda Gokuldoss and published by MDPI. This book was released on 2020-04-15 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is one of the manufacturing processes that warrants the attention of industrialists, researchers and scientists, because of its ability to produce materials with a complex shape without theoretical restrictions and with added functionalities. There are several advantages to employing additive manufacturing as the primary additive manufacturing process. However, there exist several challenges that need to be addressed systematically. A couple such issues are alloy design and process development. Traditionally alloys designed for conventional cast/powder metallurgical processes were fabricated using advanced AM processes. This is the wrong approach considering that the alloys should be coined based on the process characteristics and meta-stable nature of the process. Hence, we must focus on alloy design and development for AM that suits the AM processes. The AM processes, however, improve almost every day, either in terms of processing capabilities or processing conditions. Hence, the processing part warrants a section that is devoted to these advancements and innovations. Accordingly, the present Special Issue (book) focuses on two aspects of alloy development and process innovations. Here, 45 articles are presented covering different AM processes including selective laser melting, electron beam melting, laser cladding, direct metal laser sintering, ultrasonic consolidation, wire arc additive manufacturing, and hybrid manufacturing. I believe that this Special Issue bears is vital to the field of AM and will be a valuable addition.