Download or read book The Theory and Design of Cycloconverters written by William McMurray and published by MIT Press (MA). This book was released on 1972 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the first definitive treatment of an analytically complex type of electric power converter (cycloconverter) operating between ac sources and loads, where the output frequency can be independently controlled from the input frequency. Currently, there is much interest in applying cycloconverters to the special control of ac motors and to aircraft electrical systems; however, progress has been limited by lack of good technical information. This book provides an immeasurable service in that the author's theory is sufficiently detailed to allow accurate performance evaluation, design calculations, and cost projections. Moreover, he has culled an extensive, coherent bibliography from the scattered literature in the field. A cycloconverter of the naturally commutated type is essentially a pair of phase-controlled rectifiers connected in inverse parallel. Modulation of these converters to provide ac power at a lower frequency than the source frequency greatly complicates the analysis of their behavior. McMurray treats various effects of the modulation in theoretical detail and shows how the resulting equations can be used for accurate performance and design calculations. His analysis of the cycloconverter is based on the classical equations of a phase-controlled rectifier operating with continuous load current. The general algebraic form of the equations, which are applicable to many different circuit configurations, is retained throughout the book. It also presents in tabular and graphical form the results of numerical integration of corresponding rectifier equations, required in calculating many cycloconverter performance factors. This is the fourth monograph in the series Modern Electrical Technology, edited by Alexander Kusko.
Download or read book Power Electronics written by Issa Batarseh and published by Springer. This book was released on 2017-12-22 with total page 677 pages. Available in PDF, EPUB and Kindle. Book excerpt: This fully updated textbook provides complete coverage of electrical circuits and introduces students to the field of energy conversion technologies, analysis and design. Chapters are designed to equip students with necessary background material in such topics as devices, switching circuit analysis techniques, converter types, and methods of conversion. The book contains a large number of examples, exercises, and problems to help enforce the material presented in each chapter. A detailed discussion of resonant and softswitching dc-to-dc converters is included along with the addition of new chapters covering digital control, non-linear control, and micro-inverters for power electronics applications. Designed for senior undergraduate and graduate electrical engineering students, this book provides students with the ability to analyze and design power electronic circuits used in various industrial applications.
Download or read book Reference Data for Engineers written by Mac E. Van Valkenburg and published by Newnes. This book was released on 2001-09-26 with total page 1696 pages. Available in PDF, EPUB and Kindle. Book excerpt: This standard handbook for engineers covers the fundamentals, theory and applications of radio, electronics, computers, and communications equipment. It provides information on essential, need-to-know topics without heavy emphasis on complicated mathematics. It is a "must-have" for every engineer who requires electrical, electronics, and communications data. Featured in this updated version is coverage on intellectual property and patents, probability and design, antennas, power electronics, rectifiers, power supplies, and properties of materials. Useful information on units, constants and conversion factors, active filter design, antennas, integrated circuits, surface acoustic wave design, and digital signal processing is also included. This work also offers new knowledge in the fields of satellite technology, space communication, microwave science, telecommunication, global positioning systems, frequency data, and radar.
Download or read book Renewable Energy Systems written by Fang Lin Luo and published by CRC Press. This book was released on 2012-09-07 with total page 883 pages. Available in PDF, EPUB and Kindle. Book excerpt: Energy conversion techniques are key in power electronics and even more so in renewable energy source systems, which require a large number of converters. Renewable Energy Systems: Advanced Conversion Technologies and Applications describes advanced conversion technologies and provides design examples of converters and inverters for renewable energy systems—including wind turbine and solar panel energy systems. Learn Cutting-Edge Techniques for Converters and Inverters Setting the scene, the book begins with a review of the basics of astronomy and Earth physics. It then systematically introduces more than 200 topologies of advanced converters originally developed by the authors, including 150 updated circuits on modern conversion technologies. It also discusses recently published topologies and thoroughly analyzes new converter circuits. Novel approaches include split-capacitor and split-inductor techniques that can be applied in super-lift and other converters. Resolve Historic Problems in Conversion Technologies Along with offering many cutting-edge techniques, the authors resolve some historic problems, such as the accurate determination of the conduction angle of single-phase rectifiers and power factor correction. They also describe a new series—laddered multilevel inverters—that uses few devices to produce more levels, overcoming the drawbacks of the pulse-width-modulation (PWM) inverter and providing great scope for industrial applications. Tap the Knowledge of Pioneers in the Field This book is written by pioneers in advanced conversion technology who have created a large number of converters, including the world-renowned DC/DC Luo-converters and super-lift Luo-converters. Featuring numerous examples and diagrams, it guides readers in designing advanced converters for use in renewable energy systems.
Download or read book Power Electronics written by Fang Lin Luo and published by CRC Press. This book was released on 2018-01-02 with total page 707 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power Electronics is a large size technology, mainly covering four categories: the AC/DC rectifiers, DC/DC converters, DC/AC inverters, and AC/AC converters. This book offers approximately 100 novel topologies of all four. The applications are used in sustainable energy generation areas, such as distributed generation (DG), micro-grid (MG), smart grid (SG) systems, and electrical vehicles (EV). With case studies from GE, AEG, Simplatroll Ltd, and Chinese Power Manufacturing Co., the reader will be exposed to practical applications in industry and real-world settings. This new edition features an entirely new chapter on best switching angles to obtain lowest THD for multilevel DC/AC inverters. Additionally, all chapters have been updated and include homework problems throughout.
Download or read book Power Converter Circuits written by William Shepherd and published by CRC Press. This book was released on 2004-03-12 with total page 548 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text reveals all key components of rectification, inversion, cycloconversion, and conversion circuits. It authoritatively describes switching, voltage and current relationships, and converter properties, operation, control, and performance as utilized in most practical applications. Authored jointly by a veteran scholar and an accomplished researcher in the field Power Converter Circuits highlights methods grounded in classical mathematics and includes an abundance of numerical worked examples. Features hundreds of chapter-specific problems, with solutions provided separately at the end of the book
Download or read book Microprocessors in Signal Processing Measurement and Control written by S.G. Tzafestas and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 446 pages. Available in PDF, EPUB and Kindle. Book excerpt: In racent years the LSI technology has witnessed a revoluti onary development, and allowed substantial reductions in the size and cost of digital logic circuitry. Computer system building blocks have progressed from the level of discrete components to the level of complex ICs involving many logic circuits on a single "chip". The invention and wide applica tions of microprocessors have changed the philosophy of the signal processing, measurement and control engineering fields. The microprocessor-based digital signal processing systems and controllers have replaced the conventional ones based on standard analog and digital computing equipment. The first microprocessors and "on-chip" computers have appeared towards the end of 71 beginning 72. Their evolution since then and the number of applications, in which they have been utilized, have both been extremely spectacular. New system concepts and hardware/software tools are steadily under development to sup port the microprocessor in its multiple and complex tasks. The goal of this book is to provide a cohesive and well-balan ced set of contributions dealing with important aspects and applications of microprocessors to signal processing, measu rement and system control. The majority of contributions in clude sufficient review material and present rather complete treatments of the respective topics.
Download or read book Semiconductor Power Electronics written by Richard G. Hoft and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 334 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductors have been used widely in signal-level or "brain" applications. Since their invention in 1948, transistors have revolutionized the electronics industry in computers, information processing, and communications. Now, however, semiconductors are being used more and more where consid erable "brawn" is required. Devices such as high-power bipolar junction tran sistors and power field-effect transistors, as well as SCRs, TRlACs, GTOs, and other semiconductor switching devices that use a p-n-p-n regenerative effect to achieve bistable action, are expanding the power-handling horizons of semicon ductors and finding increasing application in a wide range of products including regulated power supplies, lamp dimmers, motor drives, pulse modulators, and heat controls. HVDC and electric-vehicle propulsion are two additional areas of application which may have a very significant long range impact on the tech nology. The impact of solid-state devices capable of handling appreciable power levels has yet to be fully realized. Since it first became available in late 1957, the SCR or silicon-controlled rec tifier (also called the reverse blocking triode thyristor) has become the most popular member of the thyristor family. At present, SCRs are available from a large number of manufacturers in this country and abroad. SCR ratings range from less than one ampere to over three thousand amperes with voltage ratings in excess of three thousand volts.
Download or read book Control in Power Electronics and Electrical Drives written by W. Leonhard and published by Elsevier. This book was released on 2014-05-18 with total page 1041 pages. Available in PDF, EPUB and Kindle. Book excerpt: Control in Power Electronics and Electrical Drives contains the proceedings of the Second International Federation of Automatic Control Symposium held in Düsseldorf, Germany, on October 3-5, 1977. The symposium provided a forum for discussing the effects of converter control on the design of electrical machines. Comprised of 102 chapters, this book begins by focusing on control systems employing electronic power converters, along with converter circuits and converter control procedures. The next section deals with the behavior of inverter-fed electrical machines and requirements imposed by converter operation. Topics covered include the status of power thyristors and rectifiers; the dynamic performance of converter-fed synchronous motors; and open loop control of a linear vernier reluctance motor in a stepping mode. Subsequent sections explore converter-fed alternating current and direct current drives; applications of controlled industrial drives; and solid-state energy conversion. A number of methods for analyzing power electronic circuits are discussed and illustrated. This monograph will be of interest to electronics and electrical engineers.
Download or read book Vector Control of AC Drives written by Syed A. Nasar and published by Routledge. This book was released on 2017-11-22 with total page 254 pages. Available in PDF, EPUB and Kindle. Book excerpt: Alternating current (AC) induction and synchronous machines are frequently used in variable speed drives with applications ranging from computer peripherals, robotics, and machine tools to railway traction, ship propulsion, and rolling mills. The notable impact of vector control of AC drives on most traditional and new technologies, the multitude of practical configurations proposed, and the absence of books treating this subject as a whole with a unified approach were the driving forces behind the creation of this book. Vector Control of AC Drives examines the remarkable progress achieved worldwide in vector control from its introduction in 1969 to the current technology. The book unifies the treatment of vector control of induction and synchronous motor drives using the concepts of general flux orientation and the feed-forward (indirect) and feedback (direct) voltage and current vector control. The concept of torque vector control is also introduced and applied to all AC motors. AC models for drive applications developed in complex variables (space phasors), both for induction and synchronous motors, are used throughout the book. Numerous practical implementations of vector control are described in considerable detail, followed by representative digital simulations and test results taken from the recent literature. Vector Control of AC Drives will be a welcome addition to the reference collections of electrical and mechanical engineers involved with machine and system design.
Download or read book Electric Machines written by Charles A. Gross and published by CRC Press. This book was released on 2006-10-20 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt: The two major broad applications of electrical energy are information processing and energy processing. Hence, it is no wonder that electric machines have occupied a large and revered space in the field of electrical engineering. Such an important topic requires a careful approach, and Charles A. Gross' Electric Machines offers the most balanced, application-oriented, and modern perspective on electromagnetic machines available. Written in a style that is both accessible and authoritative, this book explores all aspects of electromagnetic-mechanical (EM) machines. Rather than viewing the EM machine in isolation, the author treats the machine as part of an integrated system of source, controller, motor, and load. The discussion progresses systematically through basic machine physics and principles of operation to real-world applications and relevant control issues for each type of machine presented. Coverage ranges from DC, induction, and synchronous machines to specialized machines such as transformers, translational machines, and microelectromechanical systems (MEMS). Stimulating example applications include electric vehicles, wind energy, and vertical transportation. Numerous example problems illustrate and reinforce the concepts discussed. Along with appendices filled with unit conversions and background material, Electric Machines is a succinct, in-depth, and complete guide to understanding electric machines for novel applications.
Download or read book Power Electronics Handbook written by Muhammad H. Rashid and published by Elsevier. This book was released on 2010-07-19 with total page 1189 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power electronics, which is a rapidly growing area in terms of research and applications, uses modern electronics technology to convert electric power from one form to another, such as ac-dc, dc-dc, dc-ac, and ac-ac with a variable output magnitude and frequency. Power electronics has many applications in our every day life such as air-conditioners, electric cars, sub-way trains, motor drives, renewable energy sources and power supplies for computers. This book covers all aspects of switching devices, converter circuit topologies, control techniques, analytical methods and some examples of their applications. * 25% new content* Reorganized and revised into 8 sections comprising 43 chapters* Coverage of numerous applications, including uninterruptable power supplies and automotive electrical systems* New content in power generation and distribution, including solar power, fuel cells, wind turbines, and flexible transmission
Download or read book Electronics Engineer s Reference Book written by F. F. Mazda and published by Butterworth-Heinemann. This book was released on 2013-10-22 with total page 1032 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electronics Engineer's Reference Book, Sixth Edition is a five-part book that begins with a synopsis of mathematical and electrical techniques used in the analysis of electronic systems. Part II covers physical phenomena, such as electricity, light, and radiation, often met with in electronic systems. Part III contains chapters on basic electronic components and materials, the building blocks of any electronic design. Part IV highlights electronic circuit design and instrumentation. The last part shows the application areas of electronics such as radar and computers.
Download or read book Catalog of Copyright Entries Third Series written by Library of Congress. Copyright Office and published by Copyright Office, Library of Congress. This book was released on 1974 with total page 1076 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Power Electronics and Its Applications written by Alok Jain and published by Penram International Publishing (India) Pvt. Ltd.. This book was released on 2004 with total page 455 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Switching Power Converters written by Dorin O. Neacsu and published by CRC Press. This book was released on 2017-12-19 with total page 589 pages. Available in PDF, EPUB and Kindle. Book excerpt: An examination of all of the multidisciplinary aspects of medium- and high-power converter systems, including basic power electronics, digital control and hardware, sensors, analog preprocessing of signals, protection devices and fault management, and pulse-width-modulation (PWM) algorithms, Switching Power Converters: Medium and High Power, Second Edition discusses the actual use of industrial technology and its related subassemblies and components, covering facets of implementation otherwise overlooked by theoretical textbooks. The updated Second Edition contains many new figures, as well as new and/or improved chapters on: Thermal management and reliability Intelligent power modules AC/DC and DC/AC current source converters Multilevel converters Use of IPM within a "network of switches" concept Power semiconductors Matrix converters Practical aspects in building power converters Providing the latest research and development information, along with numerous examples of successful home appliance, aviation, naval, automotive electronics, industrial motor drive, and grid interface for renewable energy products, this edition highlights advancements in packaging technologies, tackles the advent of hybrid circuits able to incorporate control and power stages within the same package, and examines design for reliability from the system level perspective.
Download or read book Thyristor Physics written by A. Blicher and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this volume I attempt to present concisely the physical principles underlying the operation and performance characteristics of the class of semiconductor p-n-p-n switches known as thyristors. The semiconductor controlled rectifier (SCR), the triode AC switch (Triac) the gate turn-off switch (GTO), and the reverse conducting thyristor (RCT) are some of the most important devices belonging to this device family. This book is aimed both at semiconductor-device physicists, designers, and students and at those electronic circuit designers who wish to apply thyristors creatively without the limitation of con sidering them as "black boxes," described only by insufficiently understood electrical ratings. The book endeavors to present an up-to-date account of the progress made in understanding the operation, potentialities, and limitations of thyristors as switching circuit elements. It assumes some basic knowledge of transistor physics and stresses the phe nomenological aspects of thyristor theory with the use of mathe matics not going beyond calculus and differential equations. The first two chapters discuss basic thyristor operation theory. The sub sequent chapters are devoted to the study of the static and dynamic properties of the SCR, the RCT, the GTO, and the triac; they in clude discussions of forward voltage drops, maximum voltage blocking capabilities, turn-on and turn-off transients, current and voltage rise rates, and desirable and undesirable triggering effects.
