Download or read book Proceedings of the 7th Biennial Conference on Engineering Systems Design and Analysis 2004 written by and published by . This book was released on 2004 with total page 632 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mechatronics 98 written by J. Adolfsson and published by Elsevier. This book was released on 1998-08-28 with total page 941 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechatronics, a synergistic combination of mechanical, electronic and computing engineering technologies, is a truly multidisciplinary approach to engineering. New products based on mechatronic principles are demonstrating reduced mechanical complexity, increased performance and often previously impossible capabilities. This book contains the papers presented at the UK Mechatronics Forum's 6th International Conference, held in Skövde, Sweden, in September 1998. Many of these high-quality papers illustrate the tremendous influence of mechatronics on such areas as manufacturing machinery, automotive engineering, textiles manufacture, robotics, and real-time control and vision systems. There are also papers describing developments in sensors, actuators, control and data processing techniques, such as fuzzy logic and neural networks, all of which have practical application to mechatronic systems.
Download or read book Mobile Working Hydraulic System Dynamics written by Mikael Axin and published by Linköping University Electronic Press. This book was released on 2015-09-07 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis deals with innovative working hydraulic systems for mobile machines. Flow control systems are studied as an alternative to load sensing. The fundamental difference is that the pump is controlled based on the operator’s command signals rather than feedback signals from the loads. This control approach enables higher energy efficiency and there is no load pressure feedback causing stability issues. Experimental results show a reduced pump pressure margin and energy saving potential for a wheel loader application. The damping contribution from the inlet and outlet orifice in directional valves is studied. Design rules are developed and verified by experiments. A novel system architecture is proposed where flow control, load sensing and open-centre are merged into a generalized system description. The proposed system is configurable and the operator can realize the characteristics of any of the standard systems without compromising energy efficiency. This can be done non-discretely on-the-fly. Experiments show that it is possible to avoid unnecessary energy losses while improving system response and increasing stability margins compared to load sensing. Static and dynamic differences between different control modes are also demonstrated experimentally.
Download or read book Fluid Power Systems and Technology written by and published by . This book was released on 2003 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Acta Polytechnica Scandinavica written by and published by . This book was released on 2001 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mobile Working Machines written by Marcus Geimer and published by SAE International. This book was released on 2020-12-31 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mobile Working Machines are defined by three characteristics. These machines have a cer-tain task of doing a working process, they are mobile, and they have a signifi cant energy share in their working functions. The machines should be as productive, efficient and of high quality as possible. All these machines in the fi eld of agriculture, forestry, construction, logistics, municipal sector, and in other special applications work in different applications. But, many technologies placed in the machines are the same, similar or comparable; therefore, different branches can learn from each other. Mobile Working Machines provides a wide and deep view into the technologies used in these machines. Appropriate for new engineers as well as those who wish to increase their knowledge in this field, this book brings together all the latest research and development into one place.
Download or read book Service Robotics and Mechatronics written by Keiichi Shirase and published by Springer Science & Business Media. This book was released on 2009-10-24 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: In a world suffering from an ageing population and declining birth rate, service robotics and mechatronics have an increasingly vital role to play in maintaining a safe and sustainable environment for everyone. Mechatronics can be used in the reconstruction or restoration of various environments which we rely upon to survive; for example the reconstruction of a city after an earthquake, or the restoration of polluted waters This collection of papers was originally presented at the 7th International Conference on Machine Automation, 2008, in Awaji, Japan, and covers a variety of new trends in service robotics and mechatronics. Service Robotics and Mechatronics showcases the latest research in the area to provide researchers and scientists with an up-to-date source of knowledge and basis for further study, as well as offering graduate students valuable reference material.
Download or read book Lubrication and Maintenance of Industrial Machinery written by Robert M. Gresham and published by CRC Press. This book was released on 2008-10-24 with total page 298 pages. Available in PDF, EPUB and Kindle. Book excerpt: A-Z Guide for Maximum Cost Reduction and Increased Equipment Reliability To remain globally competitive, today's manufacturing operations have greatly improved, but there is one last link in the advancement evolution. The reliability of manufacturing equipment must be improved in order to maximize the productive life of the equipment, eliminate uns
Download or read book Power Transmission and Motion Control PTMC 2002 written by Clifford R. Burrows and published by John Wiley & Sons. This book was released on 2002-11-08 with total page 410 pages. Available in PDF, EPUB and Kindle. Book excerpt: The latest research on power transmission systems Power Transmission and Motion Control is a collection of papers showcased at the 2002 PTMC conference at the University of Bath. Representing the work of researchers and industry leaders from around the world, this book features the latest developments in power transmission media and systems, with an emphasis on pneumatic and hydraulic devices and systems. Insight into current projects on the forefront of technology and innovation provides an overview of the current state of the field while informing ongoing work and suggesting direction for future projects.
Download or read book Index of Conference Proceedings written by British Library. Document Supply Centre and published by . This book was released on 2003 with total page 870 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Lubrication and Tribology written by George E. Totten and published by CRC Press. This book was released on 2006-04-06 with total page 1219 pages. Available in PDF, EPUB and Kindle. Book excerpt: When it was first published some two decades ago, the original Handbook of Lubrication and Tribology stood on technology's cutting-edge as the first comprehensive reference to assist the emerging science of tribology lubrication. Later, followed by Volume II, Theory and Design and Volume III, Monitoring, Materials, Synthetic Lubricants, and Ap
Download or read book Modelling Monitoring and Diagnostic Techniques for Fluid Power Systems written by John Watton and published by Springer Science & Business Media. This book was released on 2007-03-24 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the background theory of fluid power and indicates the range of concepts needed for a modern approach to condition monitoring and fault diagnosis. The theory is leavened by 15-years-worth of practical measurements by the author, working with major fluid power companies, and real industrial case studies. Heavily supported with examples drawn from real industrial plants – the methods in this book have been shown to work.
Download or read book On Motion Control of Linear Incremental Hydraulic Actuators written by Martin Hochwallner and published by Linköping University Electronic Press. This book was released on 2017-10-24 with total page 91 pages. Available in PDF, EPUB and Kindle. Book excerpt: Linear Incremental Hydraulic Actuators combine one or more short-stroke cylinders, and two or more engaging/disengaging mechanisms into one actuator with long, medium, or even unlimited stroke length. The motion of each single short-stroke actuator concatenated by the engaging/disengaging mechanisms forms the motion of the linear incremental hydraulic actuator. The patterns of how these motions are concatenated form the gaits of a specific linear incremental hydraulic actuator. Linear incremental hydraulic actuators may have more than one gait. In an application, the gaits may be combined to achieve optimal performance at various operating points. The distinguishing characteristic of linear incremental hydraulic actuators is the incremental motion. The term incremental actuator is seen as analogous to the incremental versus absolute position sensor. Incremental actuators realize naturally relative positioning. Incremental motion means also that the behavior does not depend on an absolute position but only on the relative position within a cycle or step. Incremental actuators may realize discrete incremental or continuous incremental motion. Discrete incremental actuators can only approach discrete positions, whereby stepper drives are one prominent example. In contrast, continuous incremental actuators may approach any position. Linear electric motors are one example of continuous incremental actuators. The actuator has no inherent limitation in stroke length, as every step or cycle adds only to the state at the beginning of the step or cycle and does not depend on the absolute position. This led to the alternative working title Hydraulic Infinite Linear Actuator. Linear incremental hydraulic actuator provides long stroke, high force, and linear motion and has the potential to decrease the necessary resource usage,minimize environmental impact, e.g. from potential oil spillage,extend the range of feasible products: longer, stiffer, better, etc. This thesis presents an analysis of the characteristics and properties of linear incremental hydraulic actuators as well as the gaits and possible realizations of some gaits. The gait for continuous, smooth motion with two cylinders is comprehensively studied and a control concept for the tracking problem is proposed. The control concept encapsulates the complexity of the linear incremental hydraulic actuator so that an application does not have to deal with it. One other gait, the ballistic gait, which realizes fast, energy-efficient motion, enabling energy recuperation is studied.
Download or read book Aerospace Actuators 2 written by Jean-Charles Maré and published by John Wiley & Sons. This book was released on 2017-03-10 with total page 205 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is the second in a series of volumes which cover the topic of aerospace actuators following a systems-based approach. This second volume brings an original, functional and architectural vision to more electric aerospace actuators. The aspects of signal (Signal-by-Wire) and power (Power-by-Wire) are treated from the point of view of needs, their evolution throughout history, and operational solutions that are in service or in development. This volume is based on an extensive bibliography, numerous supporting examples and orders of magnitude which refer to flight controls and landing gear for various aircraft (fixed or rotorwing, launchers) in commercial, private and military applications. The topics covered in this set of books constitute a significant source of information for individuals and engineers from a variety of disciplines, seeking to learn more about aerospace actuation systems and components.
Download or read book On Electrohydraulic Pressure Control for Power Steering Applications written by Alessandro Dell'Amico and published by Linköping University Electronic Press. This book was released on 2016-02-04 with total page 209 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis deals with the Electrohydraulic Power Steering system for road vehicles, using electronic pressure control valves. With an ever increasing demand for safer vehicles and fewer traffic accidents, steering-related active safety functions are becoming more common in modern vehicles. Future road vehicles will also evolve towards autonomous vehicles, with several safety, environmental and financial benefits. A key component in realising such solutions is active steering. The power steering system was initially developed to ease the driver's workload by assisting in turning the wheels. This is traditionally done through a passive open-centre hydraulic system and heavy trucks must still rely on fluid power, due to the heavy work forces. Since the purpose of the original system is to control the assistive pressure, one way would be to use proportional pressure control valves. Since these are electronically controlled, active steering is possible and with closed-centre, energy efficiency can be significantly improved on. In this work, such a system is analysed in detail with the purpose of investigating the possible use of the system for Boost curve control and position control for autonomous driving. Commercially available valves are investigated since they provide an attractive solution. A model-based approach is adopted, where simulation of the system is an important tool. Another important tool is hardware-in-the-loop simulation. A test rig of an electrohydraulic power steering system, is developed. This work has shown how proportional pressure control valves can be used for Boost curve control and position control and what implications this has on a system level. As it turns out, the valves add a great deal of time lag and with the high gain from the Boost curve, this creates a control challenge. The problem can be handled by tuning the Boost gain, pressure response and damping and has been effectively shown through simulation and experiments. For position control, there is greater freedom to design the controller to fit the system. The pressure response can be made fast enough for this case and the time lag is much less critical.
Download or read book Mobile Robots for Dynamic Environments written by Marco Ceccarelli and published by Momentum Press. This book was released on 2015-06-09 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: For several decades now, mobile robots have been integral to the development of new robotic systems for new applications, even in nontechnical areas. Mobile robots have already been developed for such uses as industrial automation, medical care, space exploration, demining operations, surveillance, entertainment, museum guides and many other industrial and non-industrial applications. In some cases these products are readily available on the market. A considerable amount of literature is also available; not all of which pertains to technical issues, as listed in the chapters of this book and its companion. Readers will enjoy this book and its companion. They will utilize the knowledge gained with satisfaction and will be assisted by its content in their interdisciplinary work for engineering developments of mobile robots, in both old and new applications. This book and its companion can be used as a graduate level course book or a guide book for the practicing engineer who is working on a specific problem which is described in one of the chapters. The companion volume for this book, Designs and Prototypes of Mobile Robots, is also available from Momentum Press.
Download or read book Investigation of a Deployable Military Bridge System with a Fiberglass Reinforced Concrete Deck written by Joseph Patrick Hanus and published by . This book was released on 2007 with total page 556 pages. Available in PDF, EPUB and Kindle. Book excerpt:
