Download or read book The Factors Influencing the Fracture Characteristics of High strength Steel written by Charles W. Marschall and published by . This book was released on 1961 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Index to DMIC Reports and Memoranda written by Battelle Memorial Institute. Defense Metals Information Center and published by . This book was released on 1968 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Physical Metallurgy of Cobalt base Superalloys written by H J Wagner and published by . This book was released on 1962 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: A detailed picture is presented of the physical and chemical phenomena that affect the behavior of cobalt-base superalloys. Solid-solution strengthening is obtained from the high-melting metallic elements molybdenum, tungsten, tantalum, and columbium. These elements also participate in precipitation reactions involving their carbides. Precipitation of intermetallic compounds such as Ni3Ti is an important process in cobalt alloys containing appreciable amounts of nickel and titanium. The relationships among microstructure, heat treatment, and mechanical properties of the important commercial alloys are considered, and whenever possible, explained on the basis of the physical and chem cal processes that occur. (Author).
Download or read book The Effect of Nuclear Radiation on Structural Metals written by Frederic R. Shober and published by . This book was released on 1961 with total page 120 pages. Available in PDF, EPUB and Kindle. Book excerpt: The effect of fast-neutron (>1 Mev) irradiation on the mechanical properties of structural metals and alloys was studied. Although the yield strengths and ultimate tensile strengths are increased su stantially for most materials, the ductility suffers severe decreases. This report presents these changes in properties of several structural metals for a number of neutron exposures within the 1.0 x 10 to the 18th power to 5.0 x 10 to the 21st power n/sq cm range. Data summarizing these effects on several classes of materials such as carbon steels, low-alloy steels, stainless steels, Zr-base alloys, ni-base alloys, Al-base alloys, and Ta are given. Additional data which show the influence f irradiation temperatures and of post-irradiation annealing on the radiation-induced property changes are also given and discussed. Increases as great as 175% in yield strength, 100% in ultimate strength, and decreases of 80% in total elongation are reported for fast-neutron exposures as great as 5 10 to the 21st power n/sq cm. (Author).
Download or read book Beryllium for Structural Applications written by Webster Hodge and published by . This book was released on 1962 with total page 230 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reports of Government-supported research on the physical and process metallurgy of beryllium that were received at DMIC during the period 1958-1960, inclusive, are summarized, together with some reports and publications of foreign authors. No proprietary or classified information is included. In addition, reference is made to some of the more importa t writings on health hazards and safety procedures that appeared during the period covered. (Author).
Download or read book Summary of the Fifth Meeting of the Refractory Composites Working Group written by William D. Klopp and published by . This book was released on 1962 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Introduction to Metals for Elevated temperature Use written by James Edward Campbell and published by . This book was released on 1961 with total page 106 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Effect of Molten Alkali Metals on Containment Metals and Alloys at High Temperatures written by M. F. Amateau and published by . This book was released on 1962 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion of containment materials is the most serious problem in liquid-metal systems. Most high-temperature engineering metals such as refractory metals, nickel-base and cobalt-base superalloys, and the austenitic and ferritic stainless steels are sufficiently resistant to liquid sodium and NaK to be useful up to about 1600 F. The most important factor in the corrosion of these materials under given conditions of temperature and flow rate is the oxygen content of the sodium. No material is truly corrosion resistant to lithium, although the refractory metals tantalum, columbium, and molybdenum do have some potential for high-temperature service in engineering applications. Zirconium and pure iron may also find some limited use in lithium, especially in lower temperature, twocomponent, static systems. The cobalt- and nickel-base alloys are unsuitable for high-temperature service in liquid lithium. The nitrogen content of the lithium is a particularly important factor. Potassium, rubidium, and cesium are somewhat less corrosive than the other alkali metals. The refractory metals and alloys are little affected by these liquid metals. The sliding and bearing properties of metals are generally affected adversely by the presence of pure molten metals. (Author).
Download or read book Statistical Analysis of Tensile Properties of Heat treated Ti 4A1 3Mo 1V and Ti 2 5A1 16V Sheet written by G. H Beatty and published by . This book was released on 1961 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: IN THE SOLUTION TREATED AND AGED CONDITION, Ti4Al-3Mo-1V has a higher ultimate strength than does Ti-2.5Al-16V, but the two alloys are about even in yield strength and elongation. In the solution-treated condition, Ti-4Al-3Mo-1V is unquestionably stronger than Ti-2.5Al-16V. These conclusions are independent of producer. There is not much difference in the same alloy produced by different companies. The alloys developed under the Titanium-Alloy Sheet-Rolling Program would not endure the most critical interpretation of release property specifications. On the other hand, these alloys come reasonably close to specifications. A complete set of release property specifications is available only for specimens that have been solution treated and aged. Such specimens do not all exhibit the desired ultimate and yield strength, but the percentage of rejects is small enough to be encouraging. (Author).
Download or read book Department of Defense Refractory Metals Sheet rolling Program written by H. R. Ogden and published by . This book was released on 1961 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: A summary is presented of the status of the Department of Defense Refractory Metals SheetRolling Program to accelerate the development of production techniques for high-quality, consistent sheet products from the refractory metals (Nb, Mo, Ta, and W) and their alloys. The program includes: (1) development of sheet production techniques, (2) establishment of minimum data re uired to evaluate mill production, (3) evaluation of fabrication characteristics of the sheet produced, and (4) establishment of design data. Contracts were awarded for the development of sheet production techniques for all four refractory metals. One contract was awarded for the evaluation of Mo alloy sheet fabrication characteristics. (Author).
Download or read book Coatings for the Protection of Refractory Metals from Oxidation written by Carol Alnoth Krier and published by . This book was released on 1961 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas pressure Bonding written by S. J. Paprocki and published by . This book was released on 1961 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Classification of DMIC Reports and Memoranda by Major Subject written by and published by . This book was released on 1964 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: To aid in quick identification and easy location of specific technical data and information in the various reports and memoranda which have been prepared and distributed by the Defense Metals Information Center, as well as by DMIC's forerunner, the Titanium Metallurgical Laboratory, a classification by major subject matter was prepared. The classification covers reports through DMIC Report 193 and memoranda through DMIC Memorandum 183. (Author).
Download or read book Background for the Development of Materials to be Used in High strength steel Structural Weldments written by Battelle Memorial Institute and published by . This book was released on 1961 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Effects of Alloying Elements in Titanium written by D. J. Maykuth and published by . This book was released on 1961 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design Information on AM 350 Stainless Steel for Aircraft and Missiles written by R. J. Favor and published by . This book was released on 1961 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Evolution of Ultrahigh strength Hardenable Steels for Solid propellant Rocket motor Cases written by H. J. Hucek and published by . This book was released on 1961 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt:
