Download or read book The Effect of Prechambers on Flame Propagation in a Natural gas Powered Engine written by and published by . This book was released on 1995 with total page 23 pages. Available in PDF, EPUB and Kindle. Book excerpt: Large-bore two-stroke natural-gas-fueled engines commonly are located along natural gas pipelines, siphoning off a small portion of gas from the pipeline for use as a fuel, in order to pump the remaining gas along the pipeline. The KIVA-3 computational fluid dynamics program was used to simulate the compression stroke, combustion, and power stroke in a natural-gas-fueled engine by solving the full Navier-Stokes equations. These calculations include cases with and without prechambers. Prechamber stoichiometry and spark locations were independently varied with the goal of understanding how various prechamber parameters influence the ignition of the fuel-air charge in the main chamber. The goal is to allow the use of very lean main-chamber charges to minimize nitrogen oxide (NO(subscript x)) production. These calculations were performed in both two and three dimensions.
Download or read book Flame Propagation in Natural Gas Fueled Direct Injection Engines microform written by Mark A. (Mark Adam) Fabbroni and published by Library and Archives Canada = Bibliothèque et Archives Canada. This book was released on 2004 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: Natural gas has shown promise as an alternative fuel for diesel engines. Research has shown that natural gas requires assistance to ignite in a diesel engine chamber. This results in a single site of ignition from which the flame must propagate to other jets in the injection pattern. The goal of this work was to determine what factors affect how the flame propagates from this initial ignition site to the remaining unburned mixture. The combustion of natural gas jets under diesel engine conditions was studied over a range of temperatures, pressures, equivalence ratios, and glow plug shield designs using a rapid compression device. Ignition was provided by a shielded glow plug. The results show that of all the factors considered the geometry of the injection pattern, chamber, and glow plug shield are most dominant in controlling combustion rates and efficiency.
Download or read book Modelling Spark Ignition Combustion written by P. A. Lakshminarayanan and published by Springer Nature. This book was released on with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Numerical and Experimental Study of Flame Propagation and Knock in a Compressed Natural Gas Engine written by Christian Lämmle and published by . This book was released on 2005 with total page 169 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Knocking in Gasoline Engines written by Michael Günther and published by Springer. This book was released on 2017-11-21 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book includes the papers presented at the conference discussing approaches to prevent or reliably control knocking and other irregular combustion events. The majority of today’s highly efficient gasoline engines utilize downsizing. High mean pressures produce increased knocking, which frequently results in a reduction in the compression ratio at high specific powers. Beyond this, the phenomenon of pre-ignition has been linked to the rise in specific power in gasoline engines for many years. Charge-diluted concepts with high compression cause extreme knocking, potentially leading to catastrophic failure. The introduction of RDE legislation this year will further grow the requirements for combustion process development, as residual gas scavenging and enrichment to improve the knock limit will be legally restricted despite no relaxation of the need to reach the main center of heat release as early as possible. New solutions in thermodynamics and control engineering are urgently needed to further increase the efficiency of gasoline engines.
Download or read book Natural Gas Engines written by Kalyan Kumar Srinivasan and published by Springer. This book was released on 2018-11-03 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the various advanced reciprocating combustion engine technologies that utilize natural gas and alternative fuels for transportation and power generation applications. It is divided into three major sections consisting of both fundamental and applied technologies to identify (but not limited to) clean, high-efficiency opportunities with natural gas fueling that have been developed through experimental protocols, numerical and high-performance computational simulations, and zero-dimensional, multizone combustion simulations. Particular emphasis is placed on statutes to monitor fine particulate emissions from tailpipe of engines operating on natural gas and alternative fuels.
Download or read book Fuel Economy written by John C. Hilliard and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concern about the reduced availability and the increased cost of petroleum fuels prompted great efforts in recent years to reduce the fuel consumption of auto mobiles. The ongoing efforts to reduce fuel consumption have addressed many relevant factors, including increased engine performance, reduced friction, use of lightweight materials, and reduced aerodynamic drag. The results of the investigations assessing the various factors affecting fuel economy have been published in journals, conference proceedings, and in company and government reports. This proliferation of technical information makes it difficult for workers to keep abreast of aU developments. The material presented in this book brings together in a single volume much of the relevant materials, summarizes many of the state-of-the-art theories and data, and provides extensive lists of references. Thus, it is hoped that this book will be a useful reference for specialists and practicing engineers interested in the fuel economy of automobiles. J. C. HILLIARD o. S. SPRINGER vii CONTENTS 1. AUTOMOTIVE FUEL ECONOMY David Cole I. Introduction and Background. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . n. Fuel Economy Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 A. Engine................................................... 11 B. Drive Train. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 . . . . . . . . . . . . . . C. Vehicle Factors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 . . . . . . . . . . . . . D. Operating Factors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 . . . . . . . . . . . . E. Test Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 . . . . . . . . . . . . . . . . . 2. FUEL ECONOMY AND EMISSIONS J. T. Kummer I. Introduction .................................................. . 35 n. Emission Regulations .......................................... .
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Turbulent Combustion written by Norbert Peters and published by Cambridge University Press. This book was released on 2000-08-15 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: The combustion of fossil fuels remains a key technology for the foreseeable future. It is therefore important that we understand the mechanisms of combustion and, in particular, the role of turbulence within this process. Combustion always takes place within a turbulent flow field for two reasons: turbulence increases the mixing process and enhances combustion, but at the same time combustion releases heat which generates flow instability through buoyancy, thus enhancing the transition to turbulence. The four chapters of this book present a thorough introduction to the field of turbulent combustion. After an overview of modeling approaches, the three remaining chapters consider the three distinct cases of premixed, non-premixed, and partially premixed combustion, respectively. This book will be of value to researchers and students of engineering and applied mathematics by demonstrating the current theories of turbulent combustion within a unified presentation of the field.
Download or read book Advanced Combustion Techniques and Engine Technologies for the Automotive Sector written by Akhilendra Pratap Singh and published by Springer Nature. This book was released on 2019-10-10 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses the recent advances in combustion strategies and engine technologies, with specific reference to the automotive sector. Chapters discuss the advanced combustion technologies, such as gasoline direct ignition (GDI), spark assisted compression ignition (SACI), gasoline compression ignition (GCI), etc., which are the future of the automotive sector. Emphasis is given to technologies which have the potential for utilization of alternative fuels as well as emission reduction. One special section includes a few chapters for methanol utilization in two-wheelers and four wheelers. The book will serve as a valuable resource for academic researchers and professional automotive engineers alike.
Download or read book Fundamentals of Combustion Processes written by Sara McAllister and published by Springer Science & Business Media. This book was released on 2011-05-10 with total page 315 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamentals of Combustion Processes is designed as a textbook for an upper-division undergraduate and graduate level combustion course in mechanical engineering. The authors focus on the fundamental theory of combustion and provide a simplified discussion of basic combustion parameters and processes such as thermodynamics, chemical kinetics, ignition, diffusion and pre-mixed flames. The text includes exploration of applications, example exercises, suggested homework problems and videos of laboratory demonstrations
Download or read book Ignition and Flame Propagation in an Engine Cylinder with General Fuel air Mixture Swirl written by John Claude Boutet and published by . This book was released on 1969 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Combustion in Diesel and SI Engines written by Society of Automotive Engineers and published by SAE International. This book was released on 2000 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Energy Research Abstracts written by and published by . This book was released on 1994 with total page 806 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiannual, with semiannual and annual indexes. References to all scientific and technical literature coming from DOE, its laboratories, energy centers, and contractors. Includes all works deriving from DOE, other related government-sponsored information, and foreign nonnuclear information. Arranged under 39 categories, e.g., Biomedical sciences, basic studies; Biomedical sciences, applied studies; Health and safety; and Fusion energy. Entry gives bibliographical information and abstract. Corporate, author, subject, report number indexes.
Download or read book In cylinder Laminar Flame Propagation Speed written by Leslie Bromberg and published by . This book was released on 2005 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this paper, the implication of various grades of hydrogen rich gas on the in-cylinder flame speed, and on the knock propensity, are discussed. The laminar flame propagation speed of methane with various grades of hydrogen-rich gas addition has been calculated. The effect of adding hydrogen, hydrogen rich gas from an ideal reformer (synthesis gas), as well as that from a non-catalytic plasmatron fuel reformer has been determined. The model has been used for stoichiometric as well as lean combustion. The effect of including the enthalpy of the reformate on the both the flame speed and on the propensity to knock has also been considered. A simple formula for the calculation of the flame speed for the case of mixtures of reformate and conventional fuels is proposed and has been tested against experiments at atmospheric pressure with hydrogen enriched flames.
Download or read book On Flame Propagation of Primary Reference Fuels and Reformer Gas written by Yimin Huang and published by . This book was released on 2003 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modelling Diesel Combustion written by P. A. Lakshminarayanan and published by Springer Science & Business Media. This book was released on 2010-03-03 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Phenomenology of Diesel Combustion and Modeling Diesel is the most efficient combustion engine today and it plays an important role in transport of goods and passengers on land and on high seas. The emissions must be controlled as stipulated by the society without sacrificing the legendary fuel economy of the diesel engines. These important drivers caused innovations in diesel engineering like re-entrant combustion chambers in the piston, lower swirl support and high pressure injection, in turn reducing the ignition delay and hence the nitric oxides. The limits on emissions are being continually reduced. The- fore, the required accuracy of the models to predict the emissions and efficiency of the engines is high. The phenomenological combustion models based on physical and chemical description of the processes in the engine are practical to describe diesel engine combustion and to carry out parametric studies. This is because the injection process, which can be relatively well predicted, has the dominant effect on mixture formation and subsequent course of combustion. The need for improving these models by incorporating new developments in engine designs is explained in Chapter 2. With “model based control programs” used in the Electronic Control Units of the engines, phenomenological models are assuming more importance now because the detailed CFD based models are too slow to be handled by the Electronic Control Units. Experimental work is necessary to develop the basic understanding of the pr- esses.
