Download or read book The Effect of Heat Treatment on Mechanical Properties of Additively Manufactured 17 4 PH Stainless Steel written by Nicholas Aaron Hopkins and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) is used to create geometries otherwise impossible to machine. Topology optimization, microstructural texture control, and the use of lattices could be created through AM to increase performance of systems. Currently research focuses on solution aging of printed 17-4 PH, while other heat treatments are not as heavily studied. This study identifies different heat treatments applied to additively manufactured 17-4 precipitation hardened (PH) and the effects on mechanical properties. This study used quasi-static tension, quasi-static compression, and Charpy V-notch testing to analyze the effects of heat treatment as well as the effectiveness of additive manufacturing compared to traditional machining for wrought materials. Data during testing was taken with digital image correlation to identify changes in local strain. The effectiveness of heat treatment was demonstrated in this study and can be used to estimate performance on additively produced 17-4 PH.
Download or read book Quality Analysis of Additively Manufactured Metals written by Javad Kadkhodapour and published by Elsevier. This book was released on 2022-11-30 with total page 858 pages. Available in PDF, EPUB and Kindle. Book excerpt: Quality Analysis of Additively Manufactured Metals: Simulation Approaches, Processes, and Microstructure Properties provides readers with a firm understanding of the failure and fatigue processes of additively manufactured metals. With a focus on computational methods, the book analyzes the process-microstructure-property relationship of these metals and how it affects their quality while also providing numerical, analytical, and experimental data for material design and investigation optimization. It outlines basic additive manufacturing processes for metals, strategies for modeling the microstructural features of metals and how these features differ based on the manufacturing process, and more.Improvement of additively manufactured metals through predictive simulation methods and microdamage and micro-failure in quasi-static and cyclic loading scenarios are covered, as are topology optimization methods and residual stress analysis techniques. The book concludes with a section featuring case studies looking at additively manufactured metals in automotive, biomedical and aerospace settings. - Provides insights and outlines techniques for analyzing why additively manufactured metals fail and strategies for avoiding those failures - Defines key terms and concepts related to the failure analysis, quality assurance and optimization processes of additively manufactured metals - Includes simulation results, experimental data and case studies
Download or read book WELDING METALLURGY AND WELDABILITY OF STAINLESS STEELS written by John C. Lippold and published by . This book was released on 2011-01-01 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Market_Desc: · Professional engineers, technicians, scientists, etc. working in industries where stainless steels are used for construction. This includes the power generation, energy, petrochemical, dairy, medical, electronic, defense, and construction industries.· Advanced undergraduate and graduate level students. Special Features: · Emphasizes solid fundamental underpinnings of the metallurgical principles that govern microstructure evolution and property develpment in welded stainless steels.· Presents many practical examples that demonstrate the application of fundamental metallurgical principles.· Greatly expands and updates what is currently available in other texts and handbooks in the subject matter. About The Book: This book describes the fundamental metallurgical principles that control microstructure and properties of welded stainless steels. It also serves as a practical how to guide that will allow engineers to select the proper alloys, filler metals, heat treatments, and welding conditions to insure that failures are avoided during fabrication and service. This book provides state of the art information on the topic and greatly expands and update what is currently available in other texts and handbooks.
Download or read book Springer Handbook of Additive Manufacturing written by Eujin Pei and published by Springer Nature. This book was released on 2023-11-25 with total page 994 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook is the ultimate definitive guide that covers key fundamentals and advanced applications for Additive Manufacturing. The Handbook has been structured into seven sections, comprising of a thorough Introduction to Additive Manufacturing; Design and Data; Processes; Materials; Post-processing, Testing and Inspection; Education and Training; and Applications and Case Study Examples. The general principles and functional relationships are described in each chapter and supplemented with industry use cases. The aim of this book is to help designers, engineers and manufacturers understand the state-of-the-art developments in the field of Additive Manufacturing. Although this book is primarily aimed at students and educators, it will appeal to researchers and industrial professionals working with technology users, machine or component manufacturers to help them make better decisions in the implementation of Additive Manufacturing and its applications.
Download or read book Proceedings of the 10th International Conference on Behaviour of Steel Structures in Seismic Areas written by Federico M. Mazzolani and published by Springer Nature. This book was released on 2022-05-07 with total page 1146 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume highlights the latest advances, innovations, and applications in the field of seismic design and performance of steel structures, as presented by leading international researchers and engineers at the 10th International Conference on the Behaviour of Steel Structures in Seismic Areas (STESSA), held in Timisoara, Romania, on 25-27 May 2022. It covers a diverse range of topics such as behaviour of structural members and connections, performance of structural systems, mixed and composite structures, energy dissipation systems, self-centring and low-damage systems, assessment and retrofitting, codes and standards, light-gauge systems. The contributions, which were selected by means of a rigorous international peer-review process, present a wealth of exciting ideas that will open novel research directions and foster multidisciplinary collaboration among different specialists.
Download or read book Recent Advances in Manufacturing Processes and Systems written by Harshit K. Dave and published by Springer Nature. This book was released on 2022-03-03 with total page 1006 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents select proceedings of 2nd International Conference on Recent Advances in Manufacturing (RAM 2021). The book provides insights into the current research trends and development in manufacturing processes. The topics covered include conventional and nonconventional manufacturing processes, micro and nano manufacturing processes, chemical and biochemical manufacturing, additive manufacturing, smart manufacturing, and sustainable and energy-efficient manufacturing. The contributions presented here are intended to stimulate new research directions in the manufacturing domain. This book will be useful for the beginners, researchers and professionals working in the area of industrial and production engineering and allied fields.
Download or read book Proceedings of the 61st Conference of Metallurgists COM 2022 written by Metallurgy & Materials Soc. of CIM and published by Springer Nature. This book was released on 2023-01-05 with total page 975 pages. Available in PDF, EPUB and Kindle. Book excerpt: These Proceedings represent the metallurgical engineering and materials science research presented at the 61st Annual Conference of Metallurgists. The collection themed ‘The Pathway to Net-Zero’ presents findings on a wide range of topics including: Processing of Critical Materials Towards Sustainable Circularity: Mining to Materials Deep Decarbonization Pathways for Pyrometallurgical Processes: Opportunities & Challenges Energy and Environmental Materials Light Metals for the Transportation Industry Advances in Materials Manufacturing VI – Existing and Emerging Materials Electrochemical Degradation of Multi-component Materials
Download or read book TMS 2020 149th Annual Meeting Exhibition Supplemental Proceedings written by The Minerals, Metals & Materials Society and published by Springer Nature. This book was released on 2020-02-13 with total page 2046 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection presents papers from the 149th Annual Meeting & Exhibition of The Minerals, Metals & Materials Society.
Download or read book Comparison of Additively Manufactured and Wrought 17 4 PH Stainless Steels in Ultra Low Cycle Fatigue written by Timothy Strasser and published by . This book was released on 2020 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive manufacturing (AM) processes allow for creation of complex geometries that are otherwise impractical to fabricate with traditional subtractive methods. AM technology has potential to improve the optimization of seismic lateral force resisting components which dissipate seismic energy through large plastic strains; however, the ultra low-cycle fatigue performance of AM metals are not yet well understood. Void formation during the AM fabrication process has potential to affect performance. This study compares the performance of heat-treated and non-heat-treated AM and wrought 17-4PH stainless steel in Ultra Low Cycle Fatigue. To understand ULCF performance differences between the AM and wrought specimens, post fracture microstructure, fractography, surface hardness, and material characterizations are conducted. Results indicate reduced fatigue life for AM 17-4PH stainless steel as compared to the wrought counterparts. Fatigue life reductions of 62% and 65% were measured for the AM steel materials (as compared to the wrought counterparts) at 3% and 4% applied strain amplitude respectively. Applied material heat treatments had no observable effect on ULCF performance.
Download or read book Advances in Additive Manufacturing Materials Processes and Applications written by Tarek Mabrouki and published by Springer Nature. This book was released on 2023-11-03 with total page 257 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reports on research and developments in the field of 3D printing, with a special emphasis on methods to analyse the products of additive manufacturing, and optimize different steps of the manufacturing process. Gathering selected contributions to the 2nd Advances in Additive Manufacturing Conference (AIAM' 2023), held on Mai 18-20, 2023, in Hammamet, Tunisia, this book covers a variety of topics, including: analysis of microstructure and material behavior, numerical simulation and model techniques for optimization of manufacturing processes, machine learning for quality control and automated monitoring, among others. Offering a good balance of fundamental research and industrially relevant findings, this book provides researchers and professionals with a timely snapshot of and extensive information on current developments in the field and a source of inspiration for future research and collaboration.
Download or read book TMS 2021 150th Annual Meeting Exhibition Supplemental Proceedings written by The Minerals, Metals & Materials Society and published by Springer Nature. This book was released on 2021-02-23 with total page 1062 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection presents papers from the 150th Annual Meeting & Exhibition of The Minerals, Metals & Materials Society.
Download or read book Tribology of Additively Manufactured Materials written by Pradeep Menezes and published by Elsevier. This book was released on 2022-08-12 with total page 362 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tribology of Additively Manufactured Materials: Fundamentals, Modeling, and Applications starts with a look at the history, methods and mechanics of additive manufacturing (AM), focusing on power bed fusion-based and direct energy deposition-based additive manufacturing. Following sections of the book provide a foundational background in the fundamentals of tribology, covering the basics of surface engineering, friction and wear, corrosion and tribocorrosion, and the tribological considerations of a variety of AM materials, such as friction and wear in non-metallic and metallic AM materials, degradation in non-metallic AM components, and corrosion and tribocorrosion in AM components. The book then concludes with a section covering modeling and simulation scenarios and challenges related to the tribology of AM materials, providing readers with the processing conditions needed to extend and strengthen the lifetime and durability of AM materials and components. - Provides theoretical, experimental and computational data for a better understanding of the complex tribological behaviors in additively manufactured components - Discusses applications of additively manufactured components, considering their tribological properties - Studies how unique surface roughness and texture develop in additively manufactured components and how these unique characteristics affect their tribological function - Outlines variables, additive manufacturing methods and performance of additively manufactured components - Equips readers with a better understanding of degradation effects due to tribology and corrosion
Download or read book TMS 2023 152nd Annual Meeting Exhibition Supplemental Proceedings written by The Minerals, Metals & Materials Society and published by Springer Nature. This book was released on 2023-02-06 with total page 1349 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection presents papers from the 152nd Annual Meeting & Exhibition of The Minerals, Metals & Materials Society.
Download or read book Multiscale Modeling of Additively Manufactured Metals written by Yi Zhang and published by Elsevier. This book was released on 2020-06-29 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: Multiscale Modeling of Additively Manufactured Metals: Application to Laser Powder Bed Fusion Process provides comprehensive coverage on the latest methodology in additive manufacturing (AM) modeling and simulation. Although there are extensive advances within the AM field, challenges to predictive theoretical and computational approaches still hinder the widespread adoption of AM. The book reviews metal additive materials and processes and discusses multiscale/multiphysics modeling strategies. In addition, coverage of modeling and simulation of AM process in order to understand the process-structure-property relationship is reviewed, along with the modeling of morphology evolution, phase transformation, and defect formation in AM parts. Residual stress, distortion, plasticity/damage in AM parts are also considered, with scales associated with the spatial, temporal and/or material domains reviewed. This book is useful for graduate students, engineers and professionals working on AM materials, equipment, process, development and modeling. Includes the fundamental principles of additive manufacturing modeling techniques Presents various modeling tools/software for AM modeling Discusses various design methods and how to optimize the AM process using these models
Download or read book Manufacturing and Application of Stainless Steels written by Andrea Di Schino and published by MDPI. This book was released on 2020-04-15 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stainless steels represent a quite interesting material family, both from a scientific and commercial point of view, following to their excellent combination in terms of strength and ductility together with corrosion resistance. Thanks to such properties, stainless steels have been indispensable for the technological progress during the last century and their annual consumption increased faster than other materials. They find application in all these fields requiring good corrosion resistance together with ability to be worked into complex geometries. Despite to their diffusion as a consolidated materials, many research fields are active regarding the possibility to increase stainless steels mechanical properties and corrosion resistance by grain refinement or by alloying by interstitial elements. At the same time innovations are coming from the manufacturing process of such a family of materials, also including the possibility to manufacture them starting from metals powder for 3D printing. The Special Issue scope embraces interdisciplinary work covering physical metallurgy and processes, reporting about experimental and theoretical progress concerning microstructural evolution during processing, microstructure-properties relations, applications including automotive, energy and structural.
Download or read book Proceedings of the 62nd Conference of Metallurgists COM 2023 written by Metallurgy & Materials Soc. of CIM and published by Springer Nature. This book was released on 2023-11-20 with total page 1033 pages. Available in PDF, EPUB and Kindle. Book excerpt: These Proceedings represent the metallurgical engineering and materials science research presented at the 62nd Annual Conference of Metallurgists (COM 2023), held in Toronto, Canada, from 21 to 24 August 2023. The Annual Conference of Metallurgists is organized by the Metallurgy & Materials Society of the Canadian Institute of Mining, Metallurgy and Petroleum (MetSoc of CIM). The collection themed ‘Climate Change and Sustainability’ presents findings on a wide range of topics, including: Advanced Manufacturing and Materials Sustainability: Integration for Better Outcomes Light Metals for Transportation and Next Generation Vehicles Derek Kerfoot Memorial Pressure Hydrometallurgy Symposium Laplante-Laskowski Symposium on Mineral Processing Fundamentals Wasmund Memorial Symposium of Sustainability in Pyrometallurgy
Download or read book Additive Manufacturing with Metals written by Sanjay Joshi and published by Springer Nature. This book was released on 2023-12-29 with total page 669 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook and reference provides a comprehensive treatment of additive manufacturing (AM) for metals, including design and digital work flows, process science and reliability, metallic systems, quality assurance, and applications. The book is rooted in the fundamental science necessary to develop and understand AM technologies, as well as the application of engineering principles covering several disciplines to successfully exploit this important technology. As additive manufacturing of metals is the fastest growing subset of this transformative technology, with the potential to make the widest impact to industrial production, Metals Additive Manufacturing: Design, Processes, Materials, Quality Assurance, and Applications is ideal for students in a range of engineering disciplines and practitioners working in aerospace, automotive, medical device manufacturing industries.
