Download or read book The Effect of Angle of Incidence and Reynolds Number on Heat Transfer in a Linear Turbine Cascade written by and published by . This book was released on 1991 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: The AFIT linear Turbine Cascade Test Facility was used to study the effect of the small changes in the angle of incidence on turbine blade convective heat transfer. Other parameters studied were the model Reynolds number and the freestream turbulence level. Characterization tests, performed to determine the feasibility of the study were followed by a series of tests designed to separate the effects of the angle of incidence, Reynolds number, and freestream turbulence level on convective heat transfer. For any given freestream turbulence level or angle of incidence, there is an increase in the heat transfer coefficient for an increase in the Reynolds number. For the low freestream turbulence (0.5%) configuration at a given Reynolds number, there is a decrease in the convective heat transfer coefficient with an increase in the angle of incidence, partially a result of the decrease in the cascade passage velocity and partially a result of the variation in boundary layer behavior. For the high freestream turbulence configuration (10%) at any Reynolds number, there is an obvious increase in the convective heat transfer coefficient over that for the low turbulence configuration; however, the transitional or fully turbulent boundary layer makes it difficult to observe any relation between the convective heat transfer coefficient and the angle of incidence.
Download or read book The Effect of Angle of Incidence and Reynolds Number on Heat Transfer in a Linear Turbine Cascade written by Steven G. Meschwitz (CAPT, USAF.) and published by . This book was released on 1991 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Effects of Incidence Angle Freestream Turbulence and Reynolds Number on Heat Transfer in a Linear Turbine Cascade written by S. G. Meschwitz and published by . This book was released on 1994 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 956 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High Reynolds Number and Turbulence Effects on Aerodynamics and Heat Transfer in a Turbine Cascade written by Frederick C. Yeh and published by . This book was released on 1993 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas Turbine Heat Transfer and Cooling Technology Second Edition written by Je-Chin Han and published by CRC Press. This book was released on 2012-11-27 with total page 892 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.
Download or read book Turbomachinery Fluid Dynamics and Heat Transfer written by Hah and published by Routledge. This book was released on 2017-10-02 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: This festschrift in honor of Professor Budugur Lakshminarayana's 60th birthday-based on the proceedings of a symposium on Turbomachinery Fluid Dynamics and Heat Transfer held recently at The Pennsylvania State University, University Park-provides authoritative and conclusive research results as well as new insights into complex flow features found in the turbomachinery used for propulsion, power, and industrial applications. Explaining in detail compressors, heat transfer fields in turbines, computational fluid dynamics, and unsteady flows, Turbomachinery Fluid Dynamics and Heat Transfer covers: Mixing mechanisms, annulus wall boundary layers, and the flow field in transonic turbocompressors The numerical implementation of turbulence models in a computer code Secondary flows, film cooling, and thermal turbulence modeling The visualization method of modeling using liquid crystals Innovative techniques in the computational modeling of compressor and turbine flows measurement in unsteady flows as well as axial flows and compressor noise generation And much more Generously illustrated and containing key bibliographic citations, Turbomachinery Fluid Dynamics and Heat Transfer is an indispensable resource for mechanical, design, aerospace, marine, manufacturing, materials, industrial, and reliability engineers; and upper-level undergraduate and graduate students in these disciplines.
Download or read book Endwall Heat Transfer Measurements in a Transonic Turbine Cascade written by and published by . This book was released on 1996 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: Turbine blade endwall heat transfer measurements are given for a range of Reynolds and Mach numbers. Data were obtained for Reynolds numbers based on inlet conditions of 0.5 and 1.0 x 10(exp 6), for isentropic exit Mach numbers of 1.0 and 1.3, and for freestream turbulence intensities of 0.25% and 7.0%. Tests were conducted in a linear cascade at the NASA Lewis Transonic Turbine Blade Cascade Facility. The test article was a turbine rotor with 136 deg of turning and an axial chord of 12.7 cm. The large scale allowed for very detailed measurements of both flow field and surface phenomena. The intent of the work is to provide benchmark quality data for CFD code and model verification. The flow field in the cascade is highly three-dimensional as a result of thick boundary layers at the test section inlet. Endwall heat transfer data were obtained using a steady-state liquid crystal technique.
Download or read book Masters Theses in the Pure and Applied Sciences written by Wade H. Shafer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: Masters Theses in the Pure and Applied Sciences was first conceived, published, and disseminated by the Center for Information and Numerical Data Analysis and Synthesis (CINDAS) * at Purdue University in 1 957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the activity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficial to the academic and general scientific and technical community. After five years of this joint undertaking we had concluded that it was in the interest of all con cerned if the printing and distribution of the volumes were handled by an interna tional publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and Applied Sciences has been disseminated on a worldwide basis by Plenum Publishing Cor poration of New York, and in the same year the coverage was broadened to include Canadian universities. All back issues can also be ordered from Plenum. We have reported in Volume 36 (thesis year 1991) a total of 11,024 thesis titles from 23 Canadian and 161 United States universities. We are sure that this broader base for these titles reported will greatly enhance the value of this important annual reference work. While Volume 36 reports theses submitted in 1991, on occasion, certain univer sities do report theses submitted in previous years but not reported at the time.
Download or read book Fluid Dynamics and Heat Transfer of Turbomachinery written by Budugur Lakshminarayana and published by John Wiley & Sons. This book was released on 1995-12-15 with total page 846 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the past three decades, information in the aerospace and mechanical engineering fields in general and turbomachinery in particular has grown at an exponential rate. Fluid Dynamics and Heat Transfer of Turbomachinery is the first book, in one complete volume, to bring together the modern approaches and advances in the field, providing the most up-to-date, unified treatment available on basic principles, physical aspects of the aerothermal field, analysis, performance, theory, and computation of turbomachinery flow and heat transfer. Presenting a unified approach to turbomachinery fluid dynamics and aerothermodynamics, the book concentrates on the fluid dynamic aspects of flows and thermodynamic considerations rather than on those related to materials, structure, or mechanical aspects. It covers the latest material and all types of turbomachinery used in modern-day aircraft, automotive, marine, spacecraft, power, and industrial applications; and there is an entire chapter devoted to modern approaches on computation of turbomachinery flow. An additional chapter on turbine cooling and heat transfer is unique for a turbomachinery book. The author has undertaken a systematic approach, through more than three hundred illustrations, in developing the knowledge base. He uses analysis and data correlation in his discussion of most recent developments in this area, drawn from over nine hundred references and from research projects carried out by various organizations in the United States and abroad. This book is extremely useful for anyone involved in the analysis, design, and testing of turbomachinery. For students, it can be used as a two-semester course of senior undergraduate or graduate study: the first semester dealing with the basic principles and analysis of turbomachinery, the second exploring three-dimensional viscid flows, computation, and heat transfer. Many sections are quite general and applicable to other areas in fluid dynamics and heat transfer. The book can also be used as a self-study guide to those who want to acquire this knowledge. The ordered, meticulous, and unified approach of Fluid Dynamics and Heat Transfer of Turbomachinery should make the specialization of turbomachinery in aerospace and mechanical engineering much more accessible to students and professionals alike, in universities, industry, and government. Turbomachinery theory, performance, and analysis made accessible with a new, unified approach For the first time in nearly three decades, here is a completely up-to-date and unified approach to turbomachinery fluid dynamics and aerothermodynamics. Combining the latest advances, methods, and approaches in the field, Fluid Dynamics and Heat Transfer of Turbomachinery features: The most comprehensive and complete coverage of the fluid dynamics and aerothermodynamics of turbomachinery to date A spotlight on the fluid dynamic aspects of flows and the thermodynamic considerations for turbomachinery (rather than the structural or material aspects) A detailed, step-by-step presentation of the analytical and computational models involved, which allows the reader to easily construct a flowchart from which to operate Critical reviews of all the existing analytical and numerical models, highlighting the advantages and drawbacks of each Comprehensive coverage of turbine cooling and heat transfer, a unique feature for a book on turbomachinery An appendix of basic computation techniques, numerous tables, and listings of common terminology, abbreviations, and nomenclature Broad in scope, yet concise, and drawing on the author's teaching experience and research projects for government and industry, Fluid Dynamics and Heat Transfer of Turbomachinery explains and simplifies an increasingly complex field. It is an invaluable resource for undergraduate and graduate students in aerospace and mechanical engineering specializing in turbomachinery, for research and design engineers, and for all professionals who are—or wish to be—at the cutting edge of this technology.
Download or read book Masters Theses in the Pure and Applied Sciences written by W. H. Shafer and published by Springer Science & Business Media. This book was released on 1993 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: Volume 36 reports (for thesis year 1991) a total of 11,024 thesis titles from 23 Canadian and 161 US universities. The organization of the volume, as in past years, consists of thesis titles arranged by discipline, and by university within each discipline. The titles are contributed by any and all a
Download or read book Blade Heat Transfer Measurements and Prediction in a Transonic Turbine Cascade written by and published by . This book was released on 1999 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Monthly Catalog of United States Government Publications Cumulative Index written by United States. Superintendent of Documents and published by . This book was released on 1978 with total page 1300 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Determination of Gas to blade Convection Heat transfer Coefficients on a Forced convection Water cooled Single stage Aluminum Turbine written by John C. Freche and published by . This book was released on 1951 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1999 with total page 1016 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Effects of the Thermal Boundary Condition and Turbulence on Heat Transfer from a Cylinder Flat Plate and Turbine Blade Using the Transient Shroud and Heated coating Techniques written by Robert John Butler and published by . This book was released on 1995 with total page 582 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Heat Transfer Measurements on an Incidence Tolerant Low Pressure Turbine Blade in a High Speed Linear Cascade at Low to Moderate Reynolds Numbers written by Leolein Patrick Gouemeni Moualeu and published by . This book was released on 2013 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt:
