Download or read book The Certification of Absorbed Energy 150 J Nominal of a Master Batch of Charpy V notch Reference Test Pieces written by and published by . This book was released on 2012 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the certification of ERM®-FA415s, a batch of steel Charpy V-notch certified reference test pieces. This batch will serve as a Master Batch, to be used by IRMM for the certification of secondary batches. Sets of five pieces taken from a secondary batch are distributed by IRMM and its authorised distributors for the verification of pendulum impact test machines according to ISO 148-2 [1]. The absorbed energy (KV) is procedurally defined and refers to the impact energy required to break a V-notched test piece of standardised dimensions, as defined in ISO 148-1 [2]. The certified value for KV is an estimate of the mean value of the whole batch. The obtained values are shown in the table below. The associated uncertainties are standard uncertainties corresponding to a confidence level of about 68 %. The certified value is traceable to the International System of Units (SI). The certified value is valid only for strikers with a 2 mm tip radius. The certified value is valid at (20 ± 2) °C.
Download or read book Certification of Charpy V notch Reference Test Pieces of 150 J Nominal Absorbed Energy written by and published by . This book was released on 2006 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM-FA415j, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines [1]) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of test machines [2]). The certified value for KV (= energy required to break a V-notched test piece using a pendulum impact test machine) is 149.1 J. The associated uncertainty (4.2 J, k = 2 corresponding to a confidence level of 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045-1 [3] and ISO 148 [4], via the corresponding Master Batch ERM-FA415b of the same nominal absorbed energy (150 J). ERM-FA415j has been accepted as European Reference Material (ERM) after successful peer evaluation by the partners of the European Reference Materials consortium.
Download or read book Certification of Charpy V notch Reference Test Pieces of 150 J Nominal Absorbed Energy written by A. Lamberty and published by . This book was released on 2011 with total page 21 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Certification of Charpy V notch Reference Test Pieces of 150 J Nominal Absorbed Energy written by and published by . This book was released on 2010 with total page 21 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Certification of the Absorbed Energy 150 J Nominal of Charpy V notch Reference Test Pieces written by and published by . This book was released on 2012 with total page 51 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM®-FA415v, a batch of Charpy V-notch certified reference test pieces certified for the absorbed energy (KV). Sets of five of these test pieces are used for the verification of pendulum impact test machines according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of testing machines [1]). The absorbed energy (KV) is procedurally defined and refers to the impact energy required to break a V-notched test piece of standardised dimensions, as defined in ISO 148-1 [2]. The certified value of ERM®- FA415v is made traceable to the SI, via the SI-traceable certified value of the master batch ERM®-FA415b, by testing samples of ERM®- FA415v and ERM®-FA415b under repeatability conditions on an impact pendulum verified and calibrated with SI-traceably calibrated tools. The certified value is valid only for strikers with a 2 mm tip radius. The certified value is valid at (20 ± 2) °C.
Download or read book The Certification of the Absorbed Energy 150 J Nominal of Charpy V notch Reference Test Pieces for Tests at 20 C written by and published by . This book was released on 2013 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Certification of the Absorbed Energy 150 J Nominal of Charpy V notch Reference Test Pieces for Tests at 20 C written by and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM®-FA415ai, a batch of Charpy V-notch certified reference test pieces certified for the absorbed energy (KV). Sets of five of these test pieces are used for the verification of pendulum impact test machines according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of testing machines). The absorbed energy (KV) is operationally defined and refers to the impact energy required to break a V-notched test piece of standardised dimensions, as defined in ISO 148-1. The certified value of ERM®-FA415ai is made traceable to the SI, via the SI-traceable certified value of the master batch ERM®-FA415s, by testing samples pieces of ERM®-FA415ai and ERM®-FA415s under repeatability conditions on an impact pendulum verified and calibrated with SI-traceably calibrated tools. The certified value is valid only for strikers with a 2 mm tip radius. The certified value is valid at (20 ± 2) °C.
Download or read book The Certification of the Absorbed Energy 150 J Nominal of Charpy V notch Reference Test Pieces for Tests at 20 C ERM FA415aa written by and published by . This book was released on 2013 with total page 21 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Certification of the Absorbed Energy 150 J Nominal of Charpy V notch Reference Test Pieces for Tests at 20 C written by and published by . This book was released on 2022 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM®-FA415ap, a batch of Charpy V-notch alloy steel certified reference test pieces certified for the average absorbed energy (KV). Sets of five of these test pieces are used for the indirect verification of pendulum impact test machines according to ISO 148-2. KV is operationally defined and refers to the impact energy required to break a V-notched test piece of standardised dimensions, as defined in ISO 148-1. The certified value of ERM-FA415ap is made traceable to the International System of Units (SI), via the SI-traceable certified value of the master batch ERM®-FA415s, by testing test pieces of ERM-FA415ap and ERM-FA415s under repeatability conditions on a Charpy reference pendulum verified and calibrated with SI-traceably calibrated tools. The certified value is valid only for strikers with a 2 mm tip radius. The certified value is valid at (20 ± 2) °C. The certified value for KV and the associated expanded uncertainty (k = 2 corresponding to a confidence level of about 95 %) were calculated in accordance with ISO 17034:2016 and ISO Guide 35:2017 for the mean of a set of five test pieces. The uncertainty includes contributions related to possible inhomogeneity and characterisation. Before release of the certified reference material, the certification project was subjected to peer-review experts.
Download or read book Certification of Charpy V notch Reference Test Pieces of 30 J Nominal Absorbed Energy written by and published by . This book was released on 2009 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM-FA013bb, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines [1]) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of test machines [2]). The certified value for KV (= energy required to break a V-notched test piece using a pendulum impact test machine) is 28.1 J. The associated uncertainty (0.8 J, k = 2 corresponding to a confidence level of 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045-1 [3] and ISO 148 [4], via the corresponding Master Batch ERM-FA013d of the same nominal absorbed energy (30 J).
Download or read book Certification of Charpy V notch Reference Test Pieces of 30 J Nominal Absorbed Energy written by and published by . This book was released on 2006 with total page 27 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM®-FA013aw, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines [1]) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of test machines [2]). The certified value for KV (= energy required to break a V-notched test piece using a pendulum impact test machine) is 30.9 J. The associated uncertainty (1.4 J, k = 2 corresponding to a confidence level of 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045-1 [3] and ISO 148 [4], via the corresponding Master Batch ERM®-FA013d of the same nominal absorbed energy (30 J).
Download or read book Certification of Charpy V notch Reference Test Pieces of 80 J Nominal Absorbed Energy written by and published by . This book was released on 2006 with total page 25 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM®-FA015t, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of test machines). The certified value for KV (= energy required to break a V-notched test piece using a pendulum impact test machine) is 80.4 J. The associated uncertainty (1.9 J, k = 2 corresponding to a confidence level of 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045 1 and ISO 148, via the corresponding Master Batch ERM®-FA015o of the same nominal absorbed energy (80 J).
Download or read book Certification of Charpy V notch Reference Test Pieces of 120 J Nominal Absorbed Energy written by and published by . This book was released on 2008 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Certification of Charpy V notch Reference Test Pieces of 120 J Nominal Absorbed Energy written by and published by . This book was released on 2006 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM-FA016au, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines [1]) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of test machines [2]). The certified value for KV (= energy required to break a V-notched test piece using a pendulum impact test machine) is 132.2 J. The associated uncertainty (4.3 J, k = 2 corresponding to a confidence level of 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045-1 [3] and ISO 148 [4], via the corresponding master batch ERM-FA016c of the same nominal absorbed energy (120 J).
Download or read book Certification of Charpy V notch Reference Test Pieces of 120 J Nominal Absorbed Energy written by and published by . This book was released on 2007 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM®-FA016at, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines [1]) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of test machines [2]). The certified value for KV (absorbed energy = energy required to break a V-notched test piece using a pendulum impact test machine) is 126.3 J. The associated expanded uncertainty (3.6 J, k = 2 corresponding to a confidence level of 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045-1 [3] and ISO 148 [4], via the corresponding master batch ERM®-FA016c of the same nominal absorbed energy (120 J).
Download or read book Certification of Charpy V notch Reference Test Pieces of 30 J Nominal Absorbed Energy written by and published by . This book was released on 2007 with total page 27 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM-FA013ax, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines [1]) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test - Part 2: Verification of test machines [2]). The certified value for KV (absorbed energy = energy required to break a V-notched test piece using a pendulum impact test machine) is 31.1 J. The associated expanded uncertainty (1.3 J, k = 2 corresponding to a confidence level of about 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045-1 [3] and ISO 148 [4], via the corresponding Master Batch ERM-FA013d of the same nominal absorbed energy (30 J).
Download or read book Certification of Charpy V notch Reference Test Pieces of 120 J Nominal Absorbed Energy written by and published by . This book was released on 2006 with total page 25 pages. Available in PDF, EPUB and Kindle. Book excerpt: This certification report describes the processing and characterisation of ERM-FA016as, a batch of Charpy V-notch certified reference test pieces. Sets of five of these test pieces are used for the verification of pendulum impact test machines according to EN 10045-2 (Charpy impact test on metallic materials, Part 2. Method for the verification of impact testing machines) or according to ISO 148-2 (Metallic materials - Charpy pendulum impact test, Part 2: Verification of test machines). The certified value for KV (= energy required to break a V-notched test piece using a pendulum impact test machine) is 123.9 J. The associated uncertainty (3.7 J, k = 2 corresponding to a confidence level of 95 %) is calculated for the mean of a set of five test pieces. The certified value is traceable to the Charpy impact test method as described in EN 10045 1 and ISO 148, via the corresponding Master Batch ERM-FA016c of the same nominal absorbed energy (120 J).
