Download or read book The Application of High Pressure in Metal deformation Processing written by F. W. Boulger and published by . This book was released on 1964 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: On October 3, 1963, a symposium was sponsored by the Bureau of Naval Weapons, Metalworking Processes and Equipment Program, on the application of high pressure in metal-deformation processing. Past research has shown that superimposed hydrostatic pressure can significantly increase the ductility at fracture of various materials. These observations have stimulated considerable interest in applying this hydrostatic-pressure effect to metal deformation processing, where it was anticipated that improved ductility and fabricability of brittle materials could be realized. Hydrostatic extrusion and hydrodynamic compressive forging were two such fabrication techniques discussed at the symposium, and preliminary results were found to be encouraging. Another fabrication process that will be investigated in the near future is sheet drawing, where the effect of superimposed pressure improves the ductility to fracture, it was noted that pressure cycling did not improve either the strength or ductility of steels containing various amounts of carbon. In addition to the mechanical-property effects, hydrostatic pressure has been found to affect measurably, numerous metallurgical properties of metals and alloys. (Author).
Download or read book The Application of High Pressure in Metal deformation Processing Report on an Informal Symposium of the Metalworking Processes and Equipment Program written by and published by . This book was released on 1964 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: On October 3, 1963, a symposium was sponsored by the Bureau of Naval Weapons, Metalworking Processes and Equipment Program, on the application of high pressure in metal-deformation processing. Past research has shown that superimposed hydrostatic pressure can significantly increase the ductility at fracture of various materials. These observations have stimulated considerable interest in applying this hydrostatic-pressure effect to metal deformation processing, where it was anticipated that improved ductility and fabricability of brittle materials could be realized. Hydrostatic extrusion and hydrodynamic compressive forging were two such fabrication techniques discussed at the symposium, and preliminary results were found to be encouraging. Another fabrication process that will be investigated in the near future is sheet drawing, where the effect of superimposed pressure improves the ductility to fracture, it was noted that pressure cycling did not improve either the strength or ductility of steels containing various amounts of carbon. In addition to the mechanical-property effects, hydrostatic pressure has been found to affect measurably, numerous metallurgical properties of metals and alloys. (Author).
Download or read book Metal Deformation Processing written by F. W. Boulger and published by . This book was released on 1967 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Metalworking Processes and Equipment Program, information was collected on deformation characteristics of metals and their effect on processing operations. The report presents the information collected from technical engineering reports on Government contracts and from general engineering and metallurgical publications. The objective is to help the nonspecialist in recognizing the implications of scientific findings and in applying them in specific operations. This report contains a series of articles covering the following subjects: Ductile Fracture; Application of High Pressure to the Forming of Brittle Metals; Superplasticity; Lubrication in Metal-Deformation Processes; Swaging; Adiabatic Conditions in Deformation Processing; Residual Stresses produced by Deformation. These subjects are treated in two ways: (1) generalized discussions of common processes point out why specific variables must be modified in order to deform certain types of metals satisfactorily; and (2) data on the more difficult-to-form metals are used to illustrate the principles, limitations, and effects of the processes. (Author).
Download or read book Deformation Processing written by Walter A. Backofen and published by . This book was released on 1972 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nanostructured Materials by High Pressure Severe Plastic Deformation written by Yuntian T. Zhu and published by Springer Science & Business Media. This book was released on 2006-01-20 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recently, it was reported that nanostructured materials processed under high pressure by HPT and ECAP have an extraordinary combination of both high strength and high ductility, which are two desirable, but rarely co-existing properties. These findings indicate that high-pressure is a critical factor that can be employed to process nanostructured materials with superior mechanical, and possibly also physical, properties. It is the objective of this workshop to review our current knowledge, identify issues for future research, and discuss future directions on the processing and properties of nanostructured materials via SPD techniques, with a special emphasis on high-pressure effects. The 42 peer-reviewed papers in this book cover areas of high pressure effect on the nanostructure and properties of SPD-processed materials, fundamentals of nanostructured materials, development of high-pressure SPD technologies for commercializations, recent advances of SPD technologies as well as applications and future markets of SPD-processed nanostructured materials.
Download or read book Advances in Deformation Processing written by John J. Burke and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Army Materials and Mechanics Research Center has con ducted the Sagamore Army Materials Research Conference in coop eration with the Materials Science Group of the Department of Chemical Engineering and Materials Science of Syracuse University since 1954. The purpose of the conference has been to gather to gether scientists and engineers from academic institutions, in dustry and government who are uniquely qualified to explore in depth a subject of importance to the Army, the Department of Defense and the scientific community. This volume, Advances in Deformation Processing, addresses the areas of Analytical Advances, Workability, Processing to Optimize Properties, Advanced Applications - Materials, and Advanced Applications - Processes. The dedicated assistance of Mr. Joseph Bernier of the Army Materials and Mechanics Research Center throughout the stages of the conference planning and finally the publication of the Sagamore Conference Proceedings is deeply appreciated. The support of Helen Brown DeMascio of Syracuse University in p- paring the final manuscript is acknowledged. The continued active interest and support of these conferences by Dr. A. E. Gorum, Director of the Army Materials and Mechanics Research Center, is appreciated. Syracuse University Syracuse, New York The Editors vii Contents SESSION I INTRODUCTION A. E. Gorum, Moderator Continuum Mechanics and Deformation Processing 1.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 772 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Survey of Deformation Processes and Deformation Characteristics of Difficult to Form Metals written by F. W. Boulger and published by . This book was released on 1967 with total page 321 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Materials Processes and Equipment program, information was collected on deformation characteristics of metals and their effect on processing operations. Technical engineering reports on Government contracts and general engineering and metallurgical publications were the major sources consulted. The results of the work were summarized in a series of articles covering subjects considered to be of major interest and importance. The objective was to help the nonspecialist in recognizing the implications of scientific findings and in applying them in specific operations. This report covers the following subjects: Ductile Fracture; Application of High Pressure to the Forming of Brittle Metals; Superplasticity; Lubrication in Metal-Deformation Processes; Swaging; Adiabatic Conditions in Deformation Processing; and Residual Stresses Produced by Deformation.
Download or read book Metal Deformation Processing written by F. W. Boulger and published by . This book was released on 1964 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Metalworking Process and Equipment Program, a survey was conducted to collect and summarize information on deformation characteristics of metals and their effect on processing operations. This report presents information obtained from reports on Governmentsponsored work and from articles in technical publications. The report covers eight subjects: extrusion, forging, rolling, thermal mechanical variables affecting the properties of refractory metals and alloys, development of preferred orientations, anisotropy of strength and ductility, high-strain-rate deformation, and strain aging. In order to be useful to engineering students and production engineers the topics are treated in two ways. Generalized discussions of common processes point out why specific variables must be modified in order to deform certain types of metals satisfactorily. When practical, data on the more-difficultto-form metals are used to illustrate the principles, limitations, and effects of the processes. The objective is to help the non-specialist recognize the implications of specific findings and to apply them to specific operations. (Author).
Download or read book Thermomechanical Processing of the Nickel base Alloy U 700 written by Charles P. Blankenship and published by . This book was released on 1971 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Introduction to Magnesium Alloys written by John B. Hallowell and published by . This book was released on 1964 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes the characteristics and properties of existing commercial magnesium alloys and compares these relative to each other. Although this report is not intended to serve as a source of design data for magnesium alloys, it was written to provide a simple, up-to-date background of information for the technologist who is faced with the problem of materials selection and who is unfamiliar with the advantages and discaadvantages of magnesium alloys. The eight major alloying elements which are used to control the properties of magnesium are listed along with selected data illustrating the binary phase relationships which exist, between the hexagonal, close-packed structure of magnesium and each of these metals. The nomenclature system for commercial magnesium alloys is explained and compositions and available forms of the alloys are given. Property comparisons of both cast and wrought alloys are presented. There is a section in the report dealing with the joining, forming, and machining of magnesium, and a section devoted to a discussion of a number of finishing systems which have been developed for magnesium alloys. (Author).
Download or read book U S Government Metalworking Processes and Equipment Program written by F. C. Holden and published by . This book was released on 1964 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: A summary is given of the status of the various contracts involved in the U.S. Government's Metalworking Processes and Equipment Program. (Author).
Download or read book Metal Deformation Processing written by F. W. Boulger and published by . This book was released on 1964 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: As part of the Metalworking Process and Equipment Program, a survey was conducted to collect and summarize information on deformation characteristics of metals and their effect on processing operations. This report presents information obtained from reports on Governmentsponsored work and from articles in technical publications. The report covers eight subjects: extrusion, forging, rolling, thermal mechanical variables affecting the properties of refractory metals and alloys, development of preferred orientations, anisotropy of strength and ductility, high-strain-rate deformation, and strain aging. In order to be useful to engineering students and production engineers the topics are treated in two ways. Generalized discussions of common processes point out why specific variables must be modified in order to deform certain types of metals satisfactorily. When practical, data on the more-difficultto-form metals are used to illustrate the principles, limitations, and effects of the processes. The objective is to help the non-specialist recognize the implications of specific findings and to apply them to specific operations. (Author).
Download or read book U S Government Research Reports written by and published by . This book was released on 1964 with total page 2180 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Unit Manufacturing Processes written by National Research Council and published by National Academies Press. This book was released on 1995-01-03 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: Manufacturing, reduced to its simplest form, involves the sequencing of product forms through a number of different processes. Each individual step, known as an unit manufacturing process, can be viewed as the fundamental building block of a nation's manufacturing capability. A committee of the National Research Council has prepared a report to help define national priorities for research in unit processes. It contains an organizing framework for unit process families, criteria for determining the criticality of a process or manufacturing technology, examples of research opportunities, and a prioritized list of enabling technologies that can lead to the manufacture of products of superior quality at competitive costs. The study was performed under the sponsorship of the National Science Foundation and the Defense Department's Manufacturing Technology Program.
Download or read book Bulk Nanostructured Materials written by Ruslan Z. Valiev and published by John Wiley & Sons. This book was released on 2013-09-17 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the most recent results in the area of bulk nanostructured materials and new trends in their severe plastic deformation (SPD) processing, where these techniques are now emerging from the domain of laboratory-scale research into the commercial production of various bulk nanomaterials. Special emphasis is placed on an analysis of the effect of nanostructures in materials fabricated by SPD on mechanical properties (strength and ductility, fatigue strength and life, superplasticity) and functional behavior (shape memory effects, magnetic and electric properties), as well as the numerous examples of their innovative applications. There is a high innovation potential for industrial applications of bulk nanomaterials for structural use (materials with extreme strength) as well as for functional applications such as nanomagnets, materials for hydrogen storage, thermoelectric materials, superconductors, catalysts, and biomedical implants.
Download or read book NASA Technical Note written by and published by . This book was released on 1971 with total page 478 pages. Available in PDF, EPUB and Kindle. Book excerpt:
