Download or read book System Simulation in Aircraft Landing Gear and Tire Development written by John Anthony Skorupa (CAPT, USAF.) and published by . This book was released on 1976 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book System Simulation in Aircraft Landing Gear and Tire Development written by John Anthony Skorupa and published by . This book was released on 1976 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt: Main gear load vs. time is predicted for an F-4E aircraft through the use of subsystem modeling and analog computation. Subsystems modeled are the aerodynamics, engine dynamics, vertical strut dynamics, fore-aft strut dynamics, tire/wheel dynamics, brake dynamics, and antiskid dynamics. The problem is restricted to a landing sequence with three degrees of freedom permitted for the aircraft. Aerodynamics are based on constant coefficients of lift, drag, and pitching moment. A drag chute is also employed. Engine dynamics are based on a linear thrust vs. velocity schedule. The strut dynamics are modeled by a mass-spring-damper system. The tire/wheel dynamics subsystem applies Newton's Second Law to derive the wheel slip ratio and ground-tire coefficient of friction. Brake dynamics are based on a schedule of brake torque vs. brake pressure. Antiskid dynamics model the Hytrol Mark II antiskid system. Stopping distances from simulation are compared to flight test data to verify the model. Results from the simulation agree with flight test data. A schedule of main gear load vs. velocity is proposed as an alternative to current tire testing practice. (Author).
Download or read book A Study of Analytic Modeling Techniques for Landing Gear Dynamics written by and published by . This book was released on 1982 with total page 86 pages. Available in PDF, EPUB and Kindle. Book excerpt: The ability to accurately predict the dynamic response of an aircraft while it is operating in the taxi mode depends, in part on the correct modeling of the dynamic characteristics of the landing gear system. Traditionally, landing gear have been designed to absorb landing impact ('shock absorber') and their characteristics during periodic, oscillatory response ('spring') have been considered as secondary. With the increased emphasis on the rough or damaged field taxi operation, there is a requirement to determine the best methods for modeling the gear system. This report documents a brief review of the state of the art of gear modeling. A study was then conducted to evaluate important model parameters, using a simple cantilevered gear computer simulation. Also included is the development of a technique for the experimental determination of important gear system parameters. (Author).
Download or read book Advances in Aircraft Landing Gear written by Robert Kyle Schmidt and published by SAE International. This book was released on 2015-08-24 with total page 138 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aircraft landing gear system is relatively unique on board an aircraft—it is both structure and machine, supporting the aircraft on the ground, yet providing functions such as energy absorption during landing, retraction, steering, and braking. Advances in Aircraft Landing Gear is a collection of eleven hand-picked technical papers focusing on the significant advancements that have occurred in this field concerning numeric modeling, electric actuation, and composite materials. Additionally, papers discussing self-powered landing gear and more electrical overall aircraft architectures have been included. The content of Advances in Aircraft Landing Gear is divided into two sections: Analysis and Design Methods; and Electric Actuation, Control, and Taxi. For those looking for more information on aircraft landing gears, the SAE A-5 committee (the Aerospace Landing Gear Systems Committee), which meets twice a year, serves as a useful forum for discussion on landing gear issues and development. A current listing of documents produced and maintained by this committee appears in the appendix.
Download or read book Aircraft Tires written by Kyle Schmidt and published by SAE International. This book was released on 2022-05-27 with total page 135 pages. Available in PDF, EPUB and Kindle. Book excerpt: Landing gear provides an intriguing and compelling challenge, combining many fields of science and engineering. Designed to guide the interested reader through aircraft tire design, selection, and integration to the aircraft landing gear, this book presents a specific element of landing gear design in an accessible way. The author’s two volume treatise, The Design of Aircraft Landing, was the inspiration for this book. The Design of Aircraft Landing is a landmark work for the industry and utilizes over 1,000 pages to present a complete, in-depth study of each component that must considered when designing an aircraft’s landing gear. While recognizing that not everyone may need the entire treatise, Aircraft Tires: Key Principles for Landing Gear Design is one of three quick reference guides focusing on one key element of aircraft design and landing gear design. This volume features tire construction and terminology, mechanics of pneumatic tires, tire performance and modeling as well reviewing undesirable tire behavior. R. Kyle Schmidt has over 25 years’ experience across three countries and has held a variety of variety of engineering roles relating to the development of new landing gears and the sustainment of existing landing gears in service.
Download or read book Advances in Aircraft Brakes and Tires written by Robert Kyle Schmidt and published by SAE International. This book was released on 2015-08-24 with total page 126 pages. Available in PDF, EPUB and Kindle. Book excerpt: An aircraft’s interface with the ground—through its wheels, tires, and brakes—is critical to ensure safe and reliable operation, demanding constant technology development. Significant advancements have occurred with almost all civil airliners entering service with radial tires, and with the Boeing 787 having entered service in 2011 with electrically actuated carbon-carbon brakes. This book is divided into three sections: tires, control systems, and brakes, presenting a selection of the most relevant papers published by SAE International on these matters in the past fifteen years. They have been chosen to provide significant interest to those engineers working in the landing gear field. With almost all current large civil aircraft (and many smaller aircraft) opting exclusively for carbon-carbon brakes, a number of papers addressing the challenges of this technology are included. Papers touching on tire behavior and papers discussing brake control strategies are provided. For those looking for more information on aircraft landing gears, brakes, and tires, the SAE A-5 committee (the Aerospace Landing Gear Systems Committee), which meets twice a year, serves as a useful forum for discussion on landing gear issues and development. A current listing of documents produced and maintained by the A-5 committee is included in the appendix.
Download or read book Advances in Aircraft Landing Gear and Advances in Aircraft Brakes and Tires written by Robert Kyle Schmidt and published by . This book was released on 2015-12 with total page 260 pages. Available in PDF, EPUB and Kindle. Book excerpt: This set is comprised of two titles, Advances in Aircraft Landing Gear and Advances in Aircraft Brakes and Tires both edited by Robert Kyle Schmidt, a mechanical engineer and known expert in this subject. Advances in Aircraft Landing Gear is a collection of eleven hand-picked technical papers focusing on the significant advancements that have occurred in this field concerning numeric modeling, electric actuation, and composite materials. Advances in Aircraft Brakes and Tires focuses on the aircraft's interface with the ground - through its wheels, tires and brakes - a critical part of a safe and reliable operation. It presents a selection of the most relevant papers published by SAE International on these matters in the past fifteen years. For those looking for more information on aircraft landing gears, brakes, and tires, the SAE A-5 committee (the Aerospace Landing Gear Systems Committee), which meets twice a year, serves as a useful forum for discussion on landing gear issues and development. A current listing of documents produced and maintained by the A-5 committee is included in the appendix.
Download or read book The Design of Aircraft Landing Gear written by Robert Kyle Schmidt and published by SAE International. This book was released on 2021-02-18 with total page 1092 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aircraft landing gear and its associated systems represent a compelling design challenge: simultaneously a system, a structure, and a machine, it supports the aircraft on the ground, absorbs landing and braking energy, permits maneuvering, and retracts to minimize aircraft drag. Yet, as it is not required during flight, it also represents dead weight and significant effort must be made to minimize its total mass. The Design of Aircraft Landing Gear, written by R. Kyle Schmidt, PE (B.A.Sc. - Mechanical Engineering, M.Sc. - Safety and Aircraft Accident Investigation, Chairman of the SAE A-5 Committee on Aircraft Landing Gear), is designed to guide the reader through the key principles of landing system design and to provide additional references when available. Many problems which must be confronted have already been addressed by others in the past, but the information is not known or shared, leading to the observation that there are few new problems, but many new people. The Design of Aircraft Landing Gear is intended to share much of the existing information and provide avenues for further exploration. The design of an aircraft and its associated systems, including the landing system, involves iterative loops as the impact of each modification to a system or component is evaluated against the whole. It is rare to find that the lightest possible landing gear represents the best solution for the aircraft: the lightest landing gear may require attachment structures which don't exist and which would require significant weight and compromise on the part of the airframe structure design. With those requirements and compromises in mind,The Design of Aircraft Landing Gear starts with the study of airfield compatibility, aircraft stability on the ground, the correct choice of tires, followed by discussion of brakes, wheels, and brake control systems. Various landing gear architectures are investigated together with the details of shock absorber designs. Retraction, kinematics, and mechanisms are studied as well as possible actuation approaches. Detailed information on the various hydraulic and electric services commonly found on aircraft, and system elements such as dressings, lighting, and steering are also reviewed. Detail design points, the process of analysis, and a review of the relevant requirements and regulations round out the book content. The Design of Aircraft Landing Gear is a landmark work in the industry, and a must-read for any engineer interested in updating specific skills and students preparing for an exciting career.
Download or read book Aircraft Tires written by R. Kyle Schmidt and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Landing gear provides an intriguing and compelling challenge, combining many fields of science and engineering. Designed to guide the interested reader through aircraft tire design, selection, and integration to the aircraft landing gear, this book presents a specific element of landing gear design in an accessible way. The author's two volume treatise, The Design of Aircraft Landing, was the inspiration for this book. The Design of Aircraft Landing is a landmark work for the industry and utilizes over 1,000 pages to present a complete, in-depth study of each component that must considered when designing an aircraft's landing gear. While recognizing that not everyone may need the entire treatise, Aircraft Tires: Key Principles for Landing Gear Design is one of three quick reference guides focusing on one key element of aircraft design and landing gear design. This volume features tire construction and terminology, mechanics of pneumatic tires, tire performance and modeling as well reviewing undesirable tire behavior. R. Kyle Schmidt has over 25 years' experience across three countries and has held a variety of variety of engineering roles relating to the development of new landing gears and the sustainment of existing landing gears in service.
Download or read book An Overview of Landing Gear Dynamics written by Jocelyn I. Pritchard and published by . This book was released on 1999 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: On of the problems facing the aircraft community is landing gear dynamics, especially shimmy and brake-induced vibration. Shimmy and brake-induced vibrations can lead to accidents due to excessive wear and shortened life of gear parts and contribute to pilot and passenger discomfort. To increase understanding of these problems, a literature survey was performed. The major focus is on work from the last ten years. Some older publications are included to understand the longevity of the problem and the background from earlier researchers. The literature survey includes analyses, testing, modeling, and simulation of aircraft landing gear; and experimental validation and characterization of shimmy and brake-induced vibration of aircraft landing gear. The paper presents an overview of the problem, background information, and a history of landing gear dynamics problems and solutions. Based on the survey an assessment and recommendations of the most critically needed enhancements to the state of the art will be presented. The status of Langley work contributing to this activity will be given.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on with total page 994 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Aircraft Landing Gear Design written by Norman S. Currey and published by AIAA. This book was released on 1988 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the only book available today that covers military and commercial aircraft landing gear design. It is a comprehensive text that will lead students and engineers from the initial concepts of landing gear design through final detail design. The book provides a vital link in landing gear design technology from historical practices to modern design trends, and it considers the necessary airfield interface with landing gear design. The text is backed up by calculations, specifications, references, working examples.
Download or read book STAR written by and published by . This book was released on 1973 with total page 904 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The NASA Landing Gear Test Airplane written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-13 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: A tire and landing gear test facility has been developed and incorporated into a Convair 990 aircraft. The system can simulate tire vertical load profiles to 250,000 lb, sideslip angles to 15 degrees, and wheel braking on actual runways. Onboard computers control the preprogrammed test profiles through a feedback loop and also record three axis loads, tire slip angle, and tire condition. The aircraft to date has provided tire force and wear data for the Shuttle Orbiter tire on three different runways and at east and west coast landing sites. This report discusses the role of this facility in complementing existing ground tire and landing gear test facilities, and how this facility can simultaneously simulate the vertical load, tire slip, velocity, and surface for an entire aircraft landing. A description is given of the aircraft as well as the test system. An example of a typical test sequence is presented. Data collection and reduction from this facility are discussed, as well as accuracies of calculated parameters. Validation of the facility through ground and flight tests is presented. Tests to date have shown that this facility can operate at remote sites and gather complete data sets of load, slip, and velocity on actual runway surfaces. The ground and flight tests have led to a successful validation of this test facility. Carter, John F. and Nagy, Christopher J. Armstrong Flight Research Center RTOP 551-15-01...
Download or read book Masters Theses in the Pure and Applied Sciences written by Wade H. Shafer and published by Springer Science & Business Media. This book was released on 2013-11-21 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt: Masters Theses in the Pure and Applied Sciences was first conceived, published, and dis seminated by the Center for lnformation and Numerica/ Data Analysis and Synthesis (C/NDAS) * at Purdue University in 1957, starting its coverage of theses with the academic year 1955. Beginning with Volume 13, the printing and dissemination phases of the ac tivity were transferred to University Microfilms/Xerox of Ann Arbor, Michigan, with the thought that such an arrangement would be more beneficia! to the academic and general scientific and technical community. After fi ve years of this joint undertaking we had concluded that it was in the interest of ali concerned if the printing and distribution of the volume were handled by an international publishing house to assure improved service and broader dissemination. Hence, starting with Volume 18, Masters Theses in the Pure and App/ied Sciences has been disseminated on a worldwide basis by Plenum Publishing Corporation of New York, and in the same year the coverage was broadened to include Canadian universities. Ali back issues can also be ordered from Plenum. We have reported in Volume 21 (thesis year 1976) a total of 10,586 theses titles from 25 Canadian and 219 United States universities. We are sure that this broader base for theses titles reported will greatly enhance the value of this important annual reference work.
Download or read book The Design of Aircraft Landing Gear written by Robert Kyle Schmidt and published by SAE International. This book was released on 2021-02-18 with total page 1092 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aircraft landing gear and its associated systems represent a compelling design challenge: simultaneously a system, a structure, and a machine, it supports the aircraft on the ground, absorbs landing and braking energy, permits maneuvering, and retracts to minimize aircraft drag. Yet, as it is not required during flight, it also represents dead weight and significant effort must be made to minimize its total mass. The Design of Aircraft Landing Gear, written by R. Kyle Schmidt, PE (B.A.Sc. - Mechanical Engineering, M.Sc. - Safety and Aircraft Accident Investigation, Chairman of the SAE A-5 Committee on Aircraft Landing Gear), is designed to guide the reader through the key principles of landing system design and to provide additional references when available. Many problems which must be confronted have already been addressed by others in the past, but the information is not known or shared, leading to the observation that there are few new problems, but many new people. The Design of Aircraft Landing Gear is intended to share much of the existing information and provide avenues for further exploration. The design of an aircraft and its associated systems, including the landing system, involves iterative loops as the impact of each modification to a system or component is evaluated against the whole. It is rare to find that the lightest possible landing gear represents the best solution for the aircraft: the lightest landing gear may require attachment structures which don't exist and which would require significant weight and compromise on the part of the airframe structure design. With those requirements and compromises in mind,The Design of Aircraft Landing Gear starts with the study of airfield compatibility, aircraft stability on the ground, the correct choice of tires, followed by discussion of brakes, wheels, and brake control systems. Various landing gear architectures are investigated together with the details of shock absorber designs. Retraction, kinematics, and mechanisms are studied as well as possible actuation approaches. Detailed information on the various hydraulic and electric services commonly found on aircraft, and system elements such as dressings, lighting, and steering are also reviewed. Detail design points, the process of analysis, and a review of the relevant requirements and regulations round out the book content. The Design of Aircraft Landing Gear is a landmark work in the industry, and a must-read for any engineer interested in updating specific skills and students preparing for an exciting career.
Download or read book Developing Improved Civil Aircraft Arresting Systems written by Matthew A. Barsotti and published by Transportation Research Board. This book was released on 2009 with total page 207 pages. Available in PDF, EPUB and Kindle. Book excerpt: At head of title: Airport Cooperative Research Program.
