Download or read book Synthesis of Diamondlike Carbon Films with Superlow Friction and Wear Properties written by and published by . This book was released on 2000 with total page 23 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this study, the authors introduce a new diamondlike carbon (DLC) film providing a friction coefficient of 0.001 and wear rates of 10−9 to 10−1° mm3/N.m in inert-gas environments (e.g., dry nitrogen and argon). The film was grown on steel and sapphire substrates in a plasma enhanced chemical vapor deposition system that uses using a hydrogen-rich plasma. Employing a combination of surface and structure analytical techniques, they explored the structural chemistry of the resultant DLC films and correlated these findings with the friction and wear mechanisms of the films. The results of tribological tests under a 10-N load (creating initial peak Hertz pressures of 1 and 2.2 GPa on steel and sapphire test pairs, respectively) and at 0.2 to 0.5 m/s sliding velocities indicated that a close correlation exists between the friction and wear coefficients of DLC films and the source gas chemistry. Specifically, films grown in source gases with higher hydrogen-to-carbon ratios had the lowest fiction coefficients and the highest wear resistance. The lowest friction coefficient (0.001) was achieved with a film on sapphire substrates produced in a gas discharge plasma consisting of 25% methane and 75% hydrogen.
Download or read book Diamond Like Carbon Coatings written by Peerawatt Nunthavarawong and published by CRC Press. This book was released on 2022-08-08 with total page 329 pages. Available in PDF, EPUB and Kindle. Book excerpt: Diamond-like carbons (DLCs) display a number of attractive properties that make them versatile coating materials for a variety of applications, including extremely high hardness values, very low friction properties, very low gas permeability, good biocompatibility, and very high electrical resistivity, among others. Further research into this material is required to produce hydrogen-free DLC films and to synthesize it together with other materials, thereby obtaining better film properties. Diamond-Like Carbon Coatings: Technologies and Applications examines emerging manufacturing technologies for DLCs with the aim of improving their properties for use in practical applications. Discusses DLC coatings used in mechanical, manufacturing, and medical applications Details recent developments in the novel synthesis of DLC films Covers advances in understanding of chemical, structural, physical, mechanical, and tribological properties for modern material processing Highlights methods to yield longer service life Considers prospects for future applications of emerging DLC technologies This work is aimed at materials science and engineering researchers, advanced students, and industry professionals.
Download or read book Synthesis of Superlow Friction Carbon Films from Highly Hydrogenated Methane Plasmas written by and published by . This book was released on 2000 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this study, we investigated the friction and wear performance of diamondlike carbon films (DLC) derived from increasingly hydrogenated methane plasmas. The films were deposited on steel substrates by a plasma-enhanced chemical vapor deposition process at room temperature and the tribological tests were performed in dry nitrogen. Tests results revealed a close correlation between the hydrogen in source gas plasma and the friction and wear coefficients of the DLC films. Specifically, films grown in plasmas with higher hydrogen-to-carbon ratios had much lower friction coefficients and wear rates than did films derived from source gases with lower hydrogen-to-carbon ratios. The lowest friction coefficient (0.003) was achieved with a film derived from 25% methane--75% hydrogen, while a coefficient of 0.015 was found for films derived from pure methane. Similar correlations were observed for wear rates. Films derived from hydrogen-rich plasmas had the least wear, while films derived from pure methane suffered the highest wear. We used a combination of surface analytical methods to characterize the structure and chemistry of the DLC films and worn surfaces.
Download or read book Tribology of Diamond like Carbon Films written by Christophe Donnet and published by Springer Science & Business Media. This book was released on 2007-12-06 with total page 673 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book highlights some of the most important structural, chemical, mechanical and tribological characteristics of DLC films. It is particularly dedicated to the fundamental tribological issues that impact the performance and durability of these coatings. The book provides reliable and up-to-date information on available industrial DLC coatings and includes clear definitions and descriptions of various DLC films and their properties.
Download or read book Coatings Tribology written by Kenneth Holmberg and published by Elsevier. This book was released on 2009-03-18 with total page 577 pages. Available in PDF, EPUB and Kindle. Book excerpt: The surface coating field is a rapidly developing area of science and technology that offers new methods and techniques to control friction and wear. New coating types are continually being developed and the potential applications in different industrial fields are ever growing, ranging from machine components and consumer products to medical instruments and prostheses. This book provides an extensive review of the latest technology in the field, addressing techniques such as physical and chemical vapour deposition, the tribological properties of coatings, and coating characterization and performance evaluation techniques. Eleven different cases are examined in close detail to demonstrate the improvement of tribological properties and a guide to selecting coatings is also provided. This second edition is still the only monograph in the field to give a holistic view of the subject and presents all aspects, including test and performance data as well as insights into mechanisms and interactions, thus providing the level of understanding vital for the practical application of coatings. * An extensive review of the latest developments in the field of surface coatings * Presents both theory and practical applications * Includes a guide for selecting coatings
Download or read book Synthesis and Characterization of Diamond like Carbon Coatings Deposited by Plasma Source Ion Implantation and Conventional Ion Beam Assisted Deposition Processes written by Brian M. Stout and published by . This book was released on 1999 with total page 114 pages. Available in PDF, EPUB and Kindle. Book excerpt: Diamond-like carbon coatings produced by Plasma Source Ion Implantation (PSII) and beamline Ion Beam Assisted Deposition (IBAD) were synthesized and studied. Gas pressure and electrical current were used as variables to design four independent PSII test sets. Beamline IBAD samples were produced with a pre-optimized set of parameters. Profilometry measurements showed the films to have thicknesses between 1.44 +/- 09 and 1.64 +/- 04 microns and to possess very low roughness averages, ranging from 14 +/- 3 to 28 +/- 3 nm, which correlate with substrate surface roughness. Atomic Force Microscopy revealed that diamond-like carbon crystal sizes varied significantly with chamber pressure. Crystals were generally spherical in shape suggesting that films were highly amorphous. Microhardness and nanohardness test results showed the hardest films to be greater than 3 times the hardness of untreated steel. The elastic modulus of the films, measured during the nanohardness test, was directly related to film hardness. Fretting wear and Pin-on-Disk tests were performed to quantitatively assess the ability of films to resist wear. Fretting wear tests showed a dramatic decrease in friction for diamond-like carbon films with friction levels ranging from 10% to 30% of that of untreated steel. Pin-on-Disk tests revealed a significant improvement in wear resistance prior to stylus penetration into the substrate.
Download or read book Fundamental and Practical Aspects of Tribology written by Diana Berman and published by CRC Press. This book was released on 2024-07-18 with total page 315 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamental and Practical Aspects of Tribology introduces the rudiments of engineering surfaces and teaches the basic phenomena of interacting surfaces in relative motion, major modes of friction and wear, and theories of contact evolution and lubrication. Fundamental topics include friction, wear, and lubrication; surface properties and surface topography; friction of surfaces in contact; wear and surface failures; biotribology; boundary lubrication; fluid properties; hydrodynamic lubrication; bearing selection; and introductory micro‐ and nanotribology. This book also considers the relationship between nano‐ and macrotribology, rolling contacts, tribological problems in magnetic recording and electrical contacts, and monitoring and diagnosis of friction and wear. Offers a comprehensive review of the fundamentals, providing basic information for scientists and engineers just being introduced to the tribology field Teaches tribological methods of measurements and characterization Includes examples of real‐life tribological problems and case studies of engineering problems and solutions Gives an overview of current advancements in the field Features end‐of‐chapter problems and video content for reinforcement of material This textbook is written for students taking courses in tribology and lubrication, as well as surface engineering. It will also appeal to scientists and engineers who are new to tribology. The text also offers sample laboratory demonstrations available to qualifying adopting professors.
Download or read book Contact mechanics perspective of tribology written by Irina Goryacheva and published by Frontiers Media SA. This book was released on 2021-06-04 with total page 391 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Optical and Tribological Properties of Diamond like Carbon Films Synthesized by Plasma Immersion Ion Processing written by and published by . This book was released on 1999 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hard diamond-like carbon (DLC) films have been prepared on PMMA (Polymethyl methacrylate), glass, and Si(100) substrates using C2H2-Ar plasma immersion ion processing (PIIP). The composition, structure, and properties of the films were investigated with regard to variation of the deposition parameters. It was found that the modulation of reactive gas composition during PIIP could enhance the formation of DLC films with an increased sp3 bonding structure, improved surface smoothness, high density and high hardness. An optimal combination of good optical properties and high hardness was highly dependent on the control of hydrogen content in the DLC films. Tribological tests showed that DLC-coated glass and PMMA samples exhibited a reduced friction coefficient and enhanced wear resistance relative to uncoated glass and PMMA materials. The effects of ion energy and gas composition during PIIP deposition on the formation of optically transparent and wear resistant DLC films are discussed.
Download or read book Proceedings of Asia International Conference on Tribology 2018 written by Mohd Fadzli Bin Abdollah and published by Malaysian Tribology Society. This book was released on 2018-09-17 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: This ebook is a compilation of 234 papers presented at the 6th Asia International Conference on Tribology (ASIATRIB2018): Kuching, Sarawak - Malaysia from 17 to 20 September 2018.
Download or read book Proceedings written by John von Neumann-Institut für Computing and published by Forschungszentrum Jülich. This book was released on 2012 with total page 421 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Self Lubricating Composites written by Pradeep L. Menezes and published by Springer. This book was released on 2018-06-26 with total page 297 pages. Available in PDF, EPUB and Kindle. Book excerpt: In most tribological applications, liquid or grease based lubricants are used to facilitate the relative motion of solid bodies to minimize friction and wear between interacting surfaces. The challenges for liquid lubricants arise in extreme environmental conditions, such as very high or low temperatures, vacuum, radiation, and extreme contact pressure. At these conditions, solid lubricants may be the alternative choice which can help to decrease friction and wear without incorporating liquid lubricants. Challenges with solid lubricants are to maintain a continuous supply of solid lubricants on the contact surfaces to act as lubricous layer between two sliding surfaces. Such a continuous supply of solid lubricant is more easily maintained in the case of liquid lubricants when compared to solid lubricants. The most innovative development to ensure a continuous supply of solid lubricant to the contact surface during sliding is to introduce solid lubricant as reinforcement into the matrix of one of the sliding components. Composite materials are engineered or naturally occurring materials which contain two or more distinct constituents with significantly different chemical, physical and mechanical properties. Composites consist of reinforcement and matrix (metal, polymer and ceramics). Among various reinforcements, recent emerging material, solid lubricant, is found to have many favorable attributes such as good self-lubricant property. Self‐lubrication is the ability of material to transfer embedded solid lubricants to the contact surface to decrease wear rate and friction in the absence of an external lubricant. Self-lubricating metal matrix composites (SLMMCs) are an important category of engineering materials that are increasingly replacing a number of conventional materials in the automotive, aerospace, and marine industries due to superior tribological properties. In SLMMCs, solid lubricant materials including carbonous materials, molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN) are embedded into the metal matrices as reinforcements to manufacture a novel material with attractive self-lubricating properties. Several studies have been investigated the tribological properties of self-lubricating materials. This book fills that gap to have a reference book about self-lubricating materials and their properties to help scientists, engineers, and industries. This book will try to discuss technically about self-lubricating materials and their properties and the applications for industries. The chapters will be written by authoritative expertise in the field. Additionally, this book will demonstrate fundamental study and most advanced innovations in self-lubricating materials as regards to friction and wear. The chapters also include tribological properties of composites and coatings and some practical application of self-lubricating materials.
Download or read book Aerospace Materials Handbook written by Sam Zhang and published by CRC Press. This book was released on 2016-04-19 with total page 763 pages. Available in PDF, EPUB and Kindle. Book excerpt: Whether an airplane or a space shuttle, a flying machine requires advanced materials to provide a strong, lightweight body and a powerful engine that functions at high temperature. The Aerospace Materials Handbook examines these materials, covering traditional superalloys as well as more recently developed light alloys. Capturing state-of-the-art d
Download or read book Superlubricity written by Ali Erdemir and published by Elsevier. This book was released on 2007-03-30 with total page 525 pages. Available in PDF, EPUB and Kindle. Book excerpt: Superlubricity is defined as a sliding regime in which friction or resistance to sliding vanishes. It has been shown that energy can be conserved by further reducing/removing friction in moving mechanical systems and this book includes contributions from world-renowned scientists who address some of the most fundamental research issues in overcoming friction. Superlubricity reviews the latest methods and materials in this area of research that are aimed at removing friction in nano-to-micro scale machines and large scale engineering components. Insight is also given into the atomic-scale origins of friction in general and superlubricity while other chapters focus on experimental and practical aspects or impacts of superlubricity that will be very useful for broader industrial community. * Reviews the latest fundamental research in superlubricity today* Presents 'state-of-the-art' methods, materials, and experimental techniques* Latest developments in tribomaterials, coatings, and lubricants providing superlubricity
Download or read book Wear written by Gwidon W. Stachowiak and published by John Wiley & Sons. This book was released on 2006-08-14 with total page 478 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tribology is emerging from the realm of steam engines and crank-case lubricants and becoming key to vital new technologies such as nanotechnology and MEMS. Wear is an integral part of tribology, and an effective understanding and appreciation of wear is essential in order to achieve the reliable and efficient operation of almost any machine or device. Knowledge in the field has increased considerably over recent years, and continues to expand: this book is intended to stimulate its readers to contribute towards the progress of this fascinating subject that relates to most of the known disciplines in physical science. Wear – Materials, Mechanisms and Practice provides the reader with a unique insight into our current understanding of wear, based on the contributions of numerous internationally acclaimed specialists in the field. Offers a comprehensive review of current knowledge in the field of wear. Discusses latest topics in wear mechanism classification. Includes coverage of a wide variety of materials such as metals, polymers, polymer composites, diamonds, and diamond-like films and ceramics. Discusses the chemo-mechanical linkages that control tribology, providing a more complete treatment of the subject than just the conventional mechanical treatments. Illustrated throughout with carefully compiled diagrams that provide a unique insight into the controlling mechanisms of tribology. The state of the art research on wear and the mechanisms of wear featured will be of interest to post-graduate students and lecturers in engineering, materials science and chemistry. The practical applications discussed will appeal to practitioners across virtually all sectors of engineering and industry including electronic, mechanical and electrical, quality and reliability and design.
Download or read book Intelligent Energy Field Manufacturing written by Wenwu Zhang and published by CRC Press. This book was released on 2018-10-03 with total page 987 pages. Available in PDF, EPUB and Kindle. Book excerpt: Edited by prominent researchers and with contributions from experts in their individual areas, Intelligent Energy Field Manufacturing: Interdisciplinary Process Innovations explores a new philosophy of engineering. An in-depth introduction to Intelligent Energy Field Manufacturing (EFM), this book explores a fresh engineering methodology that not only integrates but goes beyond methodologies such as Design for Six Sigma, Lean Manufacturing, Concurrent Engineering, TRIZ, green and sustainable manufacturing, and more. This book gives a systematic introduction to classic non-mechanical manufacturing processes as well as offering big pictures of some technical frontiers in modern engineering. The book suggests that any manufacturing process is actually a process of injecting human intelligence into the interaction between material and the various energy fields in order to transfer the material into desired configurations. It discusses technological innovation, dynamic M-PIE flows, the generalities of energy fields, logic functional materials and intelligence, the open scheme of intelligent EFM implementation, and the principles of intelligent EFM. The book takes a highly interdisciplinary approach that includes research frontiers such as micro/nano fabrication, high strain rate processes, laser shock forming, materials science and engineering, bioengineering, etc., in addition to a detailed treatment of the so called "non-traditional" manufacturing processes, which covers waterjet machining, laser material processing, ultrasonic material processing, EDM/ECM, etc. Filled with illustrative pictures, figures, and tables that make technical materials more absorbable, the book cuts across multiple engineering disciplines. The majority of books in this area report the facts of proven knowledge, while the behind-the-scenes thinking is usually neglected. This book examines the big picture of manufacturing in depth before diving into the deta
Download or read book Diamond like Carbon Films written by Yuto S. Tanaka and published by Nova Biomedical Books. This book was released on 2012-02 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents current research from across the globe in the study of diamond-like carbon films. Topics discussed include the peculiarities of ion-beam synthesis of carbon-based phases; electron field emission properties of non-metal and metal doped diamond like carbon; internal stress and its reduction of hydrogenated diamond-like carbon thin films deposited by plasma CVD methods; incorporating crystalline diamond particles in diamond-like carbon films to improve their properties and diamond-like carbon films applied as an alignment layer for LCDs.
