Download or read book Study of the delamination growth in composite materials under constant driving force written by Klaus Windirsch and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Numerical Simulation of Delamination Growth in Composite Materials written by P. P. Camanho and published by . This book was released on 2001 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: The use of decohesion elements for the simulation of delamination in composite materials is reviewed. The test methods available to measure the interfacial fracture toughness used in the formulation of decohesion elements are described initially. After a brief presentation of the virtual crack technique most widely used to simulate delamination growth, the formulation of interfacial decohesion elements is described. Problems related with decohesion element constitutive equations, mixed-mode crack growth, element numerical integration and solution procedures are discussed. Based on these investigations, it is concluded that the use of interfacial decohesion elements is a promising technique that avoids the need for a pre-existing crack and pre-interfacial decohesion elements is a promising technique that avoids the need for a pre-existing crack and predefined crack paths, and that these elements can be used to simulate both delamination onset and growth.

Download or read book Delamination Buckling of Composite Materials written by L. Kachanov and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 101 pages. Available in PDF, EPUB and Kindle. Book excerpt: LIOn Delamination of Laminated Composites (a) Fiber-Reinforced Composites Considerable technological advances in the production of high-strength fibers (graphite, boron, etc.) have led to a wide use of light high-strength composite materials (graphite epoxy, boron-epoxy, etc.). It is expedient, to make thin walled composite rods, plates, and shells from such materials. Plates can be made by bonding a set of unidirectional thin fiber layers, Fig.l.l. Such plates are orthotropic, as a rule. A random short-fiber composite is shown in Fig. 1.2. Fiber-reinforced composites are widely used in thin-walled aircraft structures because of their specific high strength. For example, the graphite-epoxy composite is characterized by a unidirectional tensile strength of 1.4 GPa while the density is 1.6 Mg/rrt? . For comparison, we may take a steel (steel 4340) whose corresponding properties are identified by values like 1.2 GPa and 7.8 Mg/rrt? . 1. INTRODUCTION Figure 1.1 2 1.1. On Delamination of Laminated Composites Figure 1.2 3 1. INTRODUCTION It is characteristic for laminated plastic material to possess a fairly low bonding. Therefore, low-velocity impacts and defects in manufacturing lead to local delamination. (b) Linear Problems of Delamination Buckling Delamination can significantly reduce the compressive strength and stiffness of the laminate. Local delamination can be considered as a crack in the bond. Under buckling there appears a high interlaminate stress at the crack edge that leads to a spreading of the crack. Delamination growth can lead to structural instability.

Download or read book Analysis of Instability related Growth of a Through width Delamination written by J. D. Whitcomb and published by . This book was released on 1984 with total page 122 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Delamination and Debonding of Materials written by W. Steven Johnson and published by ASTM International. This book was released on 1985 with total page 507 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book ECCM 8 European Conference on Composite Materials written by I. Crivelli Visconti and published by Woodhead Publishing. This book was released on 1998 with total page 736 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Delamination Behaviour of Composites written by Srinivasan Sridharan and published by Elsevier. This book was released on 2008-10-21 with total page 787 pages. Available in PDF, EPUB and Kindle. Book excerpt: Given such advantages as low weight compared to strength and toughness, laminated composites are now used in a wide range of applications. Their increasing use has underlined the need to understand their principal mode of failure, delamination. This important book reviews key research in understanding and preventing delamination. The first part of the book reviews general issues such as the role of fracture mechanics in understanding delamination, design issues and ways of testing delamination resistance. Part two describes techniques for detecting and characterising delamination such as piezoelectric sensors, the use of lamb waves and acoustic emission techniques. The next two sections of the book discuss ways of studying and modelling delamination behaviour. The final part of the book reviews research on delamination behaviour in particular conditions such as shell and sandwich structures, z-pin bridging and resin bonding. With its distinguished editor and international team of contributors, Delamination behaviour of composites is a standard reference for all those researching laminated composites and using them in such diverse applications as microelectronics, aerospace, marine, automotive and civil engineering. Reviews the role of fracture mechanics in understanding delamination, design issues and ways of testing delamination resistance Discuss ways of studying and modelling delamination behaviour A standard reference for all those researching laminated composites

Download or read book Instability related Delamination Growth of Embedded and Edge Delaminations written by J. D. Whitcomb and published by . This book was released on 1988 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Delamination Growth in Composite Materials written by and published by . This book was released on 1985 with total page 123 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Numerical Modelling of Failure in Advanced Composite Materials written by Pedro P. Camanho and published by Woodhead Publishing. This book was released on 2015-08-07 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Numerical Modelling of Failure in Advanced Composite Materials comprehensively examines the most recent analysis techniques for advanced composite materials. Advanced composite materials are becoming increasingly important for lightweight design in aerospace, wind energy, and mechanical and civil engineering. Essential for exploiting their potential is the ability to reliably predict their mechanical behaviour, particularly the onset and propagation of failure. Part One investigates numerical modeling approaches to interlaminar failure in advanced composite materials. Part Two considers numerical modelling approaches to intralaminar failure. Part Three presents new and emerging advanced numerical algorithms for modeling and simulation of failure. Part Four closes by examining the various engineering and scientific applications of numerical modeling for analysis of failure in advanced composite materials, such as prediction of impact damage, failure in textile composites, and fracture behavior in through-thickness reinforced laminates. Examines the most recent analysis models for advanced composite materials in a coherent and comprehensive manner Investigates numerical modelling approaches to interlaminar failure and intralaminar failure in advanced composite materials Reviews advanced numerical algorithms for modeling and simulation of failure Examines various engineering and scientific applications of numerical modelling for analysis of failure in advanced composite materials

Download or read book Studies of Delamination Growth and Final Failure Under Tensile Loading written by Paul A. Lagace and published by . This book was released on 1987 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experiments were performed to investigate the mechanisms of delamination initiation, growth, and subsequent final failure. Specimens laminated from both Hercules AS4/3501-6 unidirectional graphite/epoxy tape and Hercules A370-5H/3501-6 woven graphite/epoxy fabric were tested to isolate the influence of interlaminar normal stress ([sigma]zz ) and thermally-induced interlaminar stresses on delamination initiation. The data was successfully correlated using the Quadratic Delamination Criterion and indicated that thermally-induced interlaminar stresses can cause delamination initiation without the application of mechanical load. Graphite/epoxy specimens in a [0n ±15 n]1 (n = 1 to 5) configuration and in a [ ±153]s configuration (specimen widths 10 mm, 20 mm, 30 mm, 50 mm, and 70 mm) were used to evaluate the effects of effective ply thickness and specimen width on delamination growth and final failure. These specimens were loaded beyond delamination initiation in increments of up to 25 MPa until final failure. Delaminated area was determined via dye penetrant-enhanced x-radiography. The results showed that growth of sufficient size to be detected by the x-radiography is delayed until the onset of transverse cracking in the angled plies. These cracks always occur at the tips of the edge delamination. The delamination front then advances with the tip of the transverse crack and extends between the tip of the crack and the free edge. This emphasizes the importance of the interaction of in-plane and out-of-plane damage modes leading to final failure. A thickness effect on growth and final failure similar to that seen for delamination initiation in earlier work was observed. There was no specimen width dependence of the stress at which significant stable growth first appeared or of the final failure stress.

Download or read book The Virtual Crack Closure Technique History Approach and Applications written by Ronald Krueger and published by . This book was released on 2002 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: An overview of the virtual crack closure technique is presented. The approach used is discussed, the history summarized, and insight into its applications provided. Equations for two-dimensional quadrilateral elements with linear and quadratic shape functions are given. Formula for applying the technique in conjuction with three-dimensional solid elements as well as plate/shell elements are also provided. Necessary modifications for the use of the method with geometrically nonlinear finite element analysis and corrections required for elements at the crack tip with different lengths and widths are discussed. The problems associated with cracks or delaminations propagating between different materials are mentioned briefly, as well as a strategy to minimize these problems. Due to an increased interest in using a fracture mechanics based approach to assess the damage tolerance of composite structures in the design phase and during certification, the engineering problems selected as examples and given as references focus on the application of the technique to components made of composite materials.

Download or read book Delamination in Advanced Composites written by Golam Newaz and published by CRC Press. This book was released on 1991-02-22 with total page 508 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Delamination in Wood Wood Products and Wood Based Composites written by Voichita Bucur and published by Springer Science & Business Media. This book was released on 2010-11-02 with total page 404 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the last quarter century, delamination has come to mean more than just a failure in adhesion between layers of bonded composite plies that might affect their load-bearing capacity. Ever-increasing computer power has meant that we can now detect and analyze delamination between, for example, cell walls in solid wood. This fast-moving and critically important field of study is covered in a book that provides everyone from manufacturers to research scientists the state of the art in wood delamination studies. Divided into three sections, the book first details the general aspects of the subject, from basic information including terminology, to the theoretical basis for the evaluation of delamination. A settled terminology in this subject area is a first key goal of the book, as the terms which describe delamination in wood and wood-based composites are numerous and often confusing. The second section examines different and highly specialized methods for delamination detection such as confocal laser scanning microscopy, light microscopy, scanning electron microscopy and ultrasonics. Ways in which NDE (non-destructive evaluation) can be employed to detect and locate defects are also covered. The book’s final section focuses on the practical aspects of this defect in a wide range of wood products covering the spectrum from trees, logs, laminated panels and glued laminated timbers to parquet floors. Intended as a primary reference, this book covers everything from the microscopic, anatomical level of delamination within solid wood sections to an examination of the interface of wood and its surface coatings. It provides readers with the perspective of industry as well as laboratory and is thus a highly practical sourcebook for wood engineers working in manufacturing as well as a comprehensively referenced text for materials scientists wrestling with the theory underlying the subject.

Download or read book Impact Behaviour of Fibre Reinforced Composite Materials and Structures written by S. R. Reid and published by Elsevier. This book was released on 2000-10-12 with total page 318 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study covers impact response, damage tolerance and failure of fibre-reinforced composite materials and structures. Materials development, analysis and prediction of structural behaviour and cost-effective design all have a bearing on the impact response of composites and this book brings together for the first time the most comprehensive and up-to-date research work from leading international experts. State of the art analysis of impact response, damage tolerance and failure of FRC materials Distinguished contributors provide expert analysis of the most recent materials and structures Valuable tool for R&D engineers, materials scientists and designers

Download or read book Analysis and Performance of Fiber Composites written by Bhagwan D. Agarwal and published by Wiley-Interscience. This book was released on 1990-10-08 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt: Having fully established themselves as workable engineering materials, composite materials are now increasingly commonplace around the world. Serves as both a text and reference guide to the behavior of composite materials in different engineering applications. Revised for this Second Edition, the text includes a general discussion of composites as material, practical aspects of design and performance, and further analysis that will be helpful to those engaged in research on composites. Each chapter closes with references for further reading and a set of problems that will be useful in developing a better understanding of the subject.

Download or read book Finite Element Analysis of Composite Materials using AbaqusTM written by Ever J. Barbero and published by CRC Press. This book was released on 2013-04-18 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: Developed from the author's graduate-level course on advanced mechanics of composite materials, Finite Element Analysis of Composite Materials with Abaqus shows how powerful finite element tools address practical problems in the structural analysis of composites. Unlike other texts, this one takes the theory to a hands-on level by actually solving