Download or read book Study of crystallography and erosion behavior of single and multilayer coatings used for applications in aero engines written by Muhammad Naveed and published by Cuvillier Verlag. This book was released on 2015-07-28 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt: Der Wunsch der Menschen nach steigender Mobilität erfordert den weltweiten Ausbau/die weltweite Expansion des Flugbetriebs. Dabei ist nicht immer auszuschließen, dass Flugzeuge und Helikopter auch staubbelastetete Gebiete durchqueren müssen. Staub-/Sandansammlungen, wie sie bei/nach Vulkanausbrüchen oder z.B. durch Sand-Transport aus der Sahara und aus industriellen Quellen in der Atmosphäre vorkommen, stellen eines der Hauptprobleme für den vorzeitigen Verschleiß von Triebwerkskomponenten dar. Der Durchsatz scharfkantiger kristalliner Staub- und Sandpartikel erodiert die Oberflächen der Turbinenschaufeln und verändert Symmetrie und Abstimmung und somit die Effizienz des Triebwerks. Ziel dieser Doktorarbeit war die Entwicklung, Herstellung und experimentelle Untersuchung aufgedampfter Schichten (PVD = Physical Vapor Deposition) zur Anwendung hinsichtlich der Verlängerung der Lebensdauer von Komponenten in Gasturbinen. In einer Vakuum-Aufdampfanlage (PVD-Anlage) wurden ein- und mehrlagige Schichten auf ein Target aufgebracht und dieses anschließend in einem Erosionsprüfstand mit unterschiedlichen Parametern getestet. Aus der Analyse von Phasenentwicklung und der mechanischen Eigenschaften für die hergestellten Beschichtungen wurde versucht, eine Prognose über das Verschleißverhalten der Beschichtung zu erstellen. Die erodierten Schichten wurden im Raster-Elektronenmikroskop (REM) untersucht und unterschiedliche Verschleißmechanismen während des Erosionsprozesses besprochen. Die Ergebnisse werden ferner anhand theoretischer Modelle und der Nano-Indentierungs-Methode diskutiert.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1976 with total page 1022 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Metals Abstracts written by and published by . This book was released on 1977 with total page 1400 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Government Reports Annual Index written by and published by . This book was released on 1980 with total page 1112 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced Aerospace Materials written by Horst Buhl and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 383 pages. Available in PDF, EPUB and Kindle. Book excerpt: Very light, very strong. extremely reliable -aircraft and aerospace engineers are. and have to be. very demanding partners in the materials community. The results of their research and development work is not only crucial for one special area of applications. but can also lead the way to new solutions in many other areas of advanced technology. Springer-Verlag and the undersigned editor are pleased to present in this volume. an overview of the many facets of materials science and technology which have been the objective of intensive and systematic research work during past decades in the laboratories of the German Aerospace Research Establishment. Its contents shows clearly the interrelations between goals defined by the user. fundamentals provided by the scientists and viable solutions developed by the practical engineer. The particular personal touch which has been given to this volume by its authors in dedicating it as a farewell present to Professor Wolfgang Bunk. inspiring sci entist and director of the DLR Intitute of Materials Research for more than 20 years. has obviously given an added value to this important publication. Surely. this truly cooperative endeavour will render a valuable service to a large interna tional community of interested readers. many of them having personal links to the Institute. its director and its staff.
Download or read book Nanotechnology Research Directions IWGN Workshop Report written by R.S. Williams and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: energy production, environmental management, transportation, communication, computation, and education. As the twenty-first century unfolds, nanotechnology's impact on the health, wealth, and security of the world's people is expected to be at least as significant as the combined influences in this century of antibiotics, the integrated circuit, and human-made polymers. Dr. Neal Lane, Advisor to the President for Science and Technology and former National Science Foundation (NSF) director, stated at a Congressional hearing in April 1998, "If I were asked for an area of science and engineering that will most likely produce the breakthroughs of tomorrow, I would point to nanoscale science and engineering. " Recognizing this potential, the White House Office of Science and Technology Policy (OSTP) and the Office of Management and Budget (OMB) have issued a joint memorandum to Federal agency heads that identifies nanotechnology as a research priority area for Federal investment in fiscal year 2001. This report charts "Nanotechnology Research Directions," as developed by the Interagency W orking Group on Nano Science, Engineering, and Technology (IWGN) of the National Science and Technology Council (NSTC). The report incorporates the views of leading experts from government, academia, and the private sector. It reflects the consensus reached at an IWGN-sponsored workshop held on January 27-29, 1999, and detailed in contributions submitted thereafter by members of the V. S. science and engineering community. (See Appendix A for a list of contributors.
Download or read book Titanium and Titanium Alloys written by Christoph Leyens and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is an excellent reference for materials scientists and engineers needing to gain more knowledge about these engineering materials. Following introductory chapters on the fundamental materials properties of titanium, readers will find comprehensive descriptions of the development, processing and properties of modern titanium alloys. There then follows detailed discussion of the applications of titanium and its alloys in aerospace, medicine, energy and automotive technology.
Download or read book Thin Film Analysis by X Ray Scattering written by Mario Birkholz and published by John Wiley & Sons. This book was released on 2006-05-12 with total page 378 pages. Available in PDF, EPUB and Kindle. Book excerpt: With contributions by Paul F. Fewster and Christoph Genzel While X-ray diffraction investigation of powders and polycrystalline matter was at the forefront of materials science in the 1960s and 70s, high-tech applications at the beginning of the 21st century are driven by the materials science of thin films. Very much an interdisciplinary field, chemists, biochemists, materials scientists, physicists and engineers all have a common interest in thin films and their manifold uses and applications. Grain size, porosity, density, preferred orientation and other properties are important to know: whether thin films fulfill their intended function depends crucially on their structure and morphology once a chemical composition has been chosen. Although their backgrounds differ greatly, all the involved specialists a profound understanding of how structural properties may be determined in order to perform their respective tasks in search of new and modern materials, coatings and functions. The author undertakes this in-depth introduction to the field of thin film X-ray characterization in a clear and precise manner.
Download or read book Materials and Processes written by Barrie D. Dunn and published by Springer. This book was released on 2015-12-29 with total page 677 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this book is to assist scientists and engineers select the ideal material or manufacturing process for particular applications; these could cover a wide range of fields, from light-weight structures to electronic hardware. The book will help in problem solving as it also presents more than 100 case studies and failure investigations from the space sector that can, by analogy, be applied to other industries. Difficult-to-find material data is included for reference. The sciences of metallic (primarily) and organic materials presented throughout the book demonstrate how they can be applied as an integral part of spacecraft product assurance schemes, which involve quality, material and processes evaluations, and the selection of mechanical and component parts. In this successor edition, which has been revised and updated, engineering problems associated with critical spacecraft hardware and the space environment are highlighted by over 500 illustrations including micrographs and fractographs. Space hardware captured by astronauts and returned to Earth from long durations in space are examined. Information detailed in the Handbook is applicable to general terrestrial applications including consumer electronics as well as high reliability systems associated with aeronautics, medical equipment and ground transportation. This Handbook is also directed to those involved in maximizing the relia bility of new materials and processes for space technology and space engineering. It will be invaluable to engineers concerned with the construction of advanced structures or mechanical and electronic sub-systems.
Download or read book Environmental Barrier Coatings written by Kang N. Lee and published by MDPI. This book was released on 2020-12-29 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt: The global increase in air travel will require commercial vehicles to be more efficient than ever before. Advanced engine hot section materials are a key technology required to keep fuel consumption and emission to a minimum in next-generation gas turbines. Ceramic matrix composites (CMCs) are the most promising material to revolutionize gas turbine hot section materials technology because of their excellent high‐temperature properties. Rapid surface recession due to volatilization by water vapor is the Achilles heel of CMCs. Environmental barrier coatings (EBCs) is an enabling technology for CMCs, since it protects CMCs from water vapor. The first CMC component entered into service in 2016 in a commercial engine, and more CMC components are scheduled to follow within the next few years. One of the most difficult challenges to CMC components is EBC durability, because failure of EBC leads to a rapid reduction in CMC component life. Key contributors to EBC failure include recession, oxidation, degradation by calcium‐aluminum‐magnesium silicates (CMAS) deposits, thermal and thermo‐mechanical strains, particle erosion, and foreign object damage (FOD). Novel EBC chemistries, creative EBC designs, and robust processes are required to meet EBC durability challenges. Engine-relevant testing, characterization, and lifing methods need to be developed to improve EBC reliability. The aim of this Special Issue is to present recent advances in EBC technology to address these issues. In particular, topics of interest include but are not limited to the following: • Novel EBC chemistries and designs; • Processing including plasma spray, suspension plasma spray, solution precursor plasma spray, slurry process, PS-PVD, EB-PVD, and CVD; • Testing, characterization, and modeling; • Lifing.
Download or read book Twentieth Century Building Materials written by Thomas C. Jester and published by Getty Publications. This book was released on 2014-08-01 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the concluding decades of the twentieth century, the historic preservation community increasingly turned its attention to modern buildings, including bungalows from the 1930s, gas stations and diners from the 1940s, and office buildings and architectural homes from the 1950s. Conservation efforts, however, were often hampered by a lack of technical information about the products used in these structures, and to fill this gap Twentieth-Century Building Materials was developed by the U.S. Department of the Interior’s National Park Service and first published in 1995. Now, this invaluable guide is being reissued—with a new preface by the book’s original editor. With more than 250 illustrations, including a full-color photographic essay, the volume remains an indispensable reference on the history and conservation of modern building materials. Thirty-seven essays written by leading experts offer insights into the history, manufacturing processes, and uses of a wide range of materials, including glass block, aluminum, plywood, linoleum, and gypsum board. Readers will also learn about how these materials perform over time and discover valuable conservation and repair techniques. Bibliographies and sources for further research complete the volume. The book is intended for a wide range of conservation professionals including architects, engineers, conservators, and material scientists engaged in the conservation of modern buildings, as well as scholars in related disciplines.
Download or read book The Science of Clays written by Swapna Mukherjee and published by Springer Science & Business Media. This book was released on 2013-10-09 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is an attempt to provide a comprehensive and coherent description of three widely separated aspects of clays: the science of clays; the industrial uses of clays; and the role of clays in the environment. Most of the existing literature lacks such an integrated study and this work endeavours to fill that gap. An exhaustive account of the science of clays is presented in Part I of the book, which includes the classification, origin and evolution, composition and internal structure, chemical and physical properties of clays; soil mechanics; and analytical techniques for determining clay constituents. Part II provides a comprehensive description of the applications of clays and their derivatives in various industries, while Part III describes the role of clays in the environment; the pollution caused by clay minerals; and the application of clays in order to prevent environmental hazards. A principal feature of the book is its explanation of how the structure and composition of particular clay types facilitate their specific industrial or environmental applications, thus describing the interrelationship between three widely varying aspects of clay. A number of thought-provoking questions are raised at the end of the work in order to leave readers with a better insight in this regard.
Download or read book Liquid Cell Electron Microscopy written by Frances M. Ross and published by Cambridge University Press. This book was released on 2017 with total page 529 pages. Available in PDF, EPUB and Kindle. Book excerpt: 2.6.2 Electrodes for Electrochemistry
Download or read book The Materials Science of Thin Films written by Milton Ohring and published by Academic Press. This book was released on 1992 with total page 744 pages. Available in PDF, EPUB and Kindle. Book excerpt: Prepared as a textbook complete with problems after each chapter, specifically intended for classroom use in universities.
Download or read book Biological Activities and Application of Marine Polysaccharides written by Emad Shalaby and published by BoD – Books on Demand. This book was released on 2017-01-11 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: Marine organisms have been under research for the last decades as a source for different active compounds with various biological activities and application in agriculture, pharmacy, medicine, environment, and industries. Marine polysaccharides from these active compounds are used as antibacterial, antiviral, antioxidant, anti-inflammation, bioremediations, etc. During the last three decades, several important factors that control the production of phytoplankton polysaccharides have been identified such as chemical concentrations, temperature, light, etc. The current book includes 14 chapters contributed by experts around the world; the chapters are categorized into three sections: Marine Polysaccharides and Agriculture, Marine Polysaccharides and Biological Activities, and Marine Polysaccharides and Industries.
Download or read book Materials Design and Manufacturing for Sustainable Environment written by Santhakumar Mohan and published by Springer Nature. This book was released on 2021-02-06 with total page 909 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises the select proceedings of the International Conference on Materials, Design and Manufacturing for Sustainable Environment (ICMDMSE 2020). The primary focus is on emerging materials and cutting-edge manufacturing technologies for sustainable environment. The book covers a wide range of topics such as advanced materials, vibration, tribology, finite element method (FEM), heat transfer, fluid mechanics, energy engineering, additive manufacturing, robotics and automation, automobile engineering, industry 4.0, MEMS and nanotechnology, optimization techniques, condition monitoring, and new paradigms in technology management. Contents of this book will be useful to students, researchers, and practitioners alike.
Download or read book Nanoscience and Nanotechnology written by Marcel Van de Voorde and published by Walter de Gruyter GmbH & Co KG. This book was released on 2018-06-11 with total page 411 pages. Available in PDF, EPUB and Kindle. Book excerpt: Innovations in Nanoscience and Nanotechnology summarizes the state of the art in nano-sized materials. The authors focus on innovation aspects and highlight potentials for future developments and applications in health care, including pharmaceutics, dentistry, and cosmetics; information and communications; energy; and chemical engineering. The chapters are written by leading researchers in nanoscience, chemistry, pharmacy, biology, chemistry, physics, engineering, medicine, and social science. The authors come from a range of backgrounds including academia, industry, and national and international laboratories around the world. This book is ideally suited for researchers and students in chemistry, physics, biology, engineering, materials science, and medicine and is a useful guide for industrialists. It aims to provide inspiration for scientists, new ideas for developers and innovators in industry, and guidelines for toxicologists. It also provides guidelines for agencies and government authorities to establish safe working conditions.
