Download or read book Structural Considerations in Developing Refractory Metal Alloys written by R. I. Jaffee and published by . This book was released on 1963 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt: Progress made in applying advanced techniques and structural concepts to the problem of strengthening the Group VI-A metals, Cr, Mo, and W, is examined. At low temperatures, T/Tm
Download or read book Refractory Metal Alloys Metallurgy and Technology written by I. Machlin and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 493 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication documents Proceedings of the Symposium on Metal lurgy and Technology of Refractory Metal Alloys, held in Washington, D.C. at the Washington Hilton Hotel on April 25-26, 1968, under sponsorship of the Refractory Metals Committee, Institute of Metals Division, of the Metallurgical Society of AIME, and the National Aeronautics and Space Administration. The Symposium presented critical reviews of selected topics in refractory metal alloys, thereby contributing to an in-depth understanding of the state-of-the-art, and establishing a base line for further research, development, and application. This Symposium is fifth in a series of conferences on refractory metals, sponsored by the Metallurgical Society of AlME. Publications issuing from the conferences are valuable technical and historical source books, tracing the evolution of refractory metals from early laboratory alloying studies to their present status as useful engineering materials. Refractory metals are arbitrarily defined by melting point. A 0 melting temperature of over 3500 F was selected as the minimum for this Symposium, thus excluding chromium and vanadium, which logically could be treated with other refractory metals in Groups VA and VIA of the periodic table. The Refractory Metals Committee is planning reviews of chromium and vanadium in subsequent conferences.
Download or read book Technical Abstract Bulletin written by and published by . This book was released on with total page 828 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book U S Government Research Reports written by and published by . This book was released on 1963 with total page 814 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Department of Defense Refractory Metals Sheet Rolling Program written by D. J. Maykuth and published by . This book was released on 1965 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report is the third of a series which will periodically summarize the status of the various contracts involved in the Department of Defense Refractory Metals Sheet Rolling Program. Under this program, selected candidate materials are being carried through one or more of the following consecutive phases: Phase I, development of a sheet-production practice; Phase II, establishment of minimum design data; and Phase III, evaluation of sheetfabrication characteristics. To the present time, 13 contracts have been funded or planned in support of the Phase I, II, and III activities. This report summarizes the status of each of these individual contracts as of November 1, 1964. The first section describes the overall program of the Department of Defense Refractory Metals Sheet Rolling Program. Following, in the order of their discussions, are sections dealing with fabricable molybdenum alloys, unalloyed tungsten, columbium alloys, and tantalum alloys. (Author).
Download or read book Classification of DMIC Reports and Memoranda by Major Subject written by and published by . This book was released on 1964 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: To aid in quick identification and easy location of specific technical data and information in the various reports and memoranda which have been prepared and distributed by the Defense Metals Information Center, as well as by DMIC's forerunner, the Titanium Metallurgical Laboratory, a classification by major subject matter was prepared. The classification covers reports through DMIC Report 193 and memoranda through DMIC Memorandum 183. (Author).
Download or read book Properties of Coated Refractory Metals written by W. A. Gibeaut and published by . This book was released on 1964 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes the information generated since the middle of 1961 on the chemical, physical, and mechanical properties of refractory metals that are coated with oxidation-resistant coatings of advanced-experimental or commercial status. It is a supplement to DMIC Report 162, Coatings for the Protection of Refractory Metals from Oxidation, dated November 24, 1961. Recent data on specific silicide- and aluminide- type coatings for columbium, molybdenum, tantalum, and tungsten and their alloys reflect general advances in coating quality and performance, understanding of the behavior of coated systems, and more complete realization of the problems associated with the use of coated hardware.
Download or read book Tungsten Research and Development Review written by J. L. Ratliff and published by . This book was released on 1963 with total page 70 pages. Available in PDF, EPUB and Kindle. Book excerpt: Government-sponsored tungsten research and development efforts encompass a broad rage of technological activities. Typifying the extreme limits of efforts since January, 1960, studies have ranged from preparation of unalloyed metal to development of high-integrity fabricated shapes of tungsten-base materials. Nine major areas outline the broad over-all effort, and each is summarized within this report by brief technical discussions of 104 separate studies on 79 research programs. Included are preparation of metal, consolidation, primary and secondary working, joining, fabrication and performance of rocket nozzles, oxidation and other high-temperature reactions, protective coatings, properties, and physical metallurgy.
Download or read book Minerals Yearbook written by and published by . This book was released on 1964 with total page 1330 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Welding and Brazing of Alloy 718 written by Robert Melvin Evans and published by . This book was released on 1964 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Because of a special interest in Alloy 718, the Defense Metals Information Center has summarized information on the welding and brazing of the alloy. Two principal resons for the interest in this alloy are its good formability and its good weldability, expecially under restraint. The greater portion of the fusion welding of Alloy 718 has been done by the gas tungsten-arc (TIG) process. A discussion of welding atmosphere, filler metals, heat treatment of welds, welding under restraint, and weld toughness is presented in the section on fusion welding. Information is also presented on resistance welding and electron-beam welding of Alloy 718. The final section of this report deals with the brazing of Alloy 718.
Download or read book An Introduction to Magnesium Alloys written by John B. Hallowell and published by . This book was released on 1964 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes the characteristics and properties of existing commercial magnesium alloys and compares these relative to each other. Although this report is not intended to serve as a source of design data for magnesium alloys, it was written to provide a simple, up-to-date background of information for the technologist who is faced with the problem of materials selection and who is unfamiliar with the advantages and discaadvantages of magnesium alloys. The eight major alloying elements which are used to control the properties of magnesium are listed along with selected data illustrating the binary phase relationships which exist, between the hexagonal, close-packed structure of magnesium and each of these metals. The nomenclature system for commercial magnesium alloys is explained and compositions and available forms of the alloys are given. Property comparisons of both cast and wrought alloys are presented. There is a section in the report dealing with the joining, forming, and machining of magnesium, and a section devoted to a discussion of a number of finishing systems which have been developed for magnesium alloys. (Author).
Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1967 with total page 896 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Explosive Forming of Metals written by D. E. Strohecker and published by . This book was released on 1964 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Oxidation of Nickel and Cobalt base Superalloys written by Carl H. Lund and published by . This book was released on 1965 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report presents information dealing with the oxidation of nickel- and cobalt-base superalloys. All of the superalloys will oxidize at high temperatures when oxygen is present in the enveloping atmosphere. The rate of oxidation depends upon alloy composition, temperature, oxygen concentration, oxides formed, diffusion rates of the metals in both base metal and oxide, diffusion rate of oxygen in the oxide, solubility of oxygen in the matrix, and a host of other variables. The effects of oxidation can be beneficial or they can be harmful. The first section of this report deals with the fundamentals of the oxidation of Ni-Cr and Co-Cr alloys. Subsequent sections discuss general surface oxidation, intergranular oxidation, other subsurface oxidation, and the effect of stress on the rate of oxidation. Numerous specific alloys are mentioned in the report; as an aid to the reader, the appendix contains an alloy index of the alloys mentioned in the report along with the compositions of the alloys, and the pages on which mention of the alloys is made.
Download or read book Metal Removal by Electrochemical Methods and Its Effects on Mechanical Properties of Metals written by John A. Gurklis and published by . This book was released on 1965 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report assembles and correlates information on the effects of electrochemical metal-removal (ECMR) processes on mechanical properties. Of special interest and concern are the effects of ECMR on fatigue strength. The report covers four electrochemical metal-removal processes: electrochemical machining (ECM), electrolytic grinding (EG), electrochemical milling, and electropolishing. General characteristics and applications of the four methods are presented and discussed; special emphasis is placed on ECM. The ECMR processes are especially useful in shaping high-strength and difficult-to-machine metals and alloys, as well as in shaping parts with unusual, complex, or fragile characteristics. (Author).
Download or read book The Engineering Properties of Tungsten and Tungsten Alloys written by F. F. Schmidt and published by . This book was released on 1963 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: The results of a state-of-the-art survey covering tungsten and ten of its alloys are presented. All data are given in tabular and graphical form covering some of the more important physical, mechanical, and metallurgical properties for each material. References are given at the conclusion of each material section.
Download or read book The Engineering Properties of Molybdenum and Molybdenum Alloys written by F. F. Schmidt and published by . This book was released on 1963 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt:
