Download or read book Stress Measurements in Bias Constructed Parachute Canopies During Inflation and at Steady state written by William L. Garrard and published by . This book was released on 1980 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper describes the results of an experimental study of canopy stresses in bias constructed solid flat parachutes. Stresses were measured in the warp and fill directions during inflation and at steady state for different values of dynamic pressure. Omega sensors were used to measure stress. These sensors were mounted along the gore center lines so that the warp and fill stress distributions could be determined as a function of distance from the vent. It was found that stresses in the fill direction were substantially larger than stresses in the warp direction.
Download or read book Parachute Canopy Stress Measurements at Steady State and During Inflation written by H. G. Heinrich and published by . This book was released on 1978 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: Circumferential stresses were measured on 5-ft flat circular block-constructed solid cloth and ring slot parachutes in a wind tunnel during inflation under infinite mass condition and at steady state. Five Omega sensors placed along gore centerlines and a force link measured stresses and the parachute force versus time. Radial stresses were measured on a 3-ft solid flat circular block-constructed parachute at steady state. Stress measurements were evaluated in view of maximum and steady-state stresses versus location and time, as well as in respect to the parachute force. The measurements indicated strong stress variations, being different for both types of parachutes. In the 3-ft solid cloth parachute, the radial stress was, at certain locations, greater than the circumferential stress.
Download or read book Experimental Stress Measurements in Parachute Canopies During Inflation and at Steady State written by Thomas Andrew Konicke and published by . This book was released on 1981 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stress Analysis of a Parachute During Inflation and at Steady State written by Helmut G. Heinrich and published by . This book was released on 1965 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt: The stresses occurring in the cloth of an opening parachute and at steady state are calculated. The method is based on assumed instantaneous and steady state shapes and related pressure distributions. It is general and may be applied to any type and size of canopy built out of solid cloth. The presented analysis is limited to canopies constructed of triangular gores, but can be extended to other gore patterns. A numerical calculation is made for the Solid Flat, Circular Parachute during the opening and at steady state.
Download or read book Exploratory Parachute Canopy Stress Measurements at Steady State and During Inflation written by Helmut G. Heinrich and published by . This book was released on 1973 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: At the 4th Aerodynamic Deceleration Systems Conference, 1973, the development of the Omega Stress Sensor and initial canopy circumferential stress measurements were reported. Following the first success, the Omega sensor was tested under conditions of rapid loading. No dynamic effects were recorded at strain rates up to 100% per second. In the further pursuit of experimental stress analysis, initial measurements of radial canopy stress were made, and it was found that at certain locations the radial stress is as high or higher than the circumferential stress. Finally, exploratory tests were made in which circumferential stresses were measured on a 5 ft model parachute during the periods of inflation and at the following steady state. All tests were made under infinite mass conditions. The stresses were measured versus time, and their instantaneous values vary with respect to time and location on the parachute canopy.
Download or read book Experimental Measurement of Parachute Canopy Stress During Inflation written by and published by . This book was released on 1978 with total page 185 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Omega sensor was developed for measuring stress in textile and other flexible materials by the Department of Aerospace Engineering and Mechanics of the University of Minnesota and sponsored by the Air Force Flight Dynamics Laboratory. Two studies were conducted by the University which indicated that the circumferential stresses of inflated parachute canopies indicated by Omega sensors agreed with theoretically predicted stresses and also that the stresses measured by an Omega sensor were not affected by dynamic loading. This particular study deals with an in-house test program, designed to measure the circumferential stresses of a model (five foot nominal diameter) ringslot parachute during inflation and at steady state using modified Omega sensors. Slight modifications to the original Omega sensor had to be made due to complications of the tabs tearing during preliminary testing. Five sensors were attached strategically to the canopy of a ringslot parachute and put through a series of low speed wind tunnel tests. The results are presented in detail and provide for the first time actual measurement of circumferential stresses on the surface of a model ringslot parachute. These results, however, can only present the general trend shown in the parachute's stress distribution and not actual stress values due to the inability to calibrate the sensor while attached to the canopy.
Download or read book Stress Measurements in a Ribbon Parachute Canopy During Inflation and at Steady State written by T. A. Konicke and published by . This book was released on 1981 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper describes the results of an experimental study of canopy stresses in a model ribbon parachute. The distribution of circumferential stress was measured during inflation and at steady state for different values of dynamic pressure. Testing was performed in the wind tunnel at the infinite mass condition. Omega sensors were used to measure stresses and were mounted in different ribbons along the gore centerline. It was found that the steady state stress had two maxima of about equal value. One maxima was near the skirt, the other half-way between the vent and skirt. The distribution of maximum stress during inflation was similar to the steady state distribution and the ratio of maximum stress during inflation to steady state stress ranged from 1.25 to 1.75 and was essentially independent of dynamic pressure. The spectral density of the steady state stress measured at several points on the canopy.
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1983 with total page 876 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Parachute Stress Analysis During Inflation and at Steady State written by H. G. Heinrich and published by . This book was released on 1964 with total page 23 pages. Available in PDF, EPUB and Kindle. Book excerpt: The stresses occurring in the cloth of a parachute during the period of inflation and under steady state are calculated for a number of instantaneous shapes which are characteristic of the opening process and the steady state. The method is general and may be applied to any type of parachute built out of solid cloth, concentric rings or ribbons. The presented analysis is related to canopies consisting of triangular gores but can be extended to other gore patterns. A numerical calculation is made for a solid flat circular parachute during the period of opening and at steady state.
Download or read book Parachute Stress Analysis During Inflation and at Steady State written by Helmut G. Heinrich and published by . This book was released on 1966 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt: The stresses occurring in the cloth of a parachute during the period of inflation and at a steady state are calculated for a number of instantaneous shapes that are characteristic of the opening process and the steady state. The method is general and may be applied to any type of parachute built out of solid cloth, concentric rings, or ribbons. The presented analysis is related to canopies consisting of triangular gores but can be extended to other gore patterns. A numerical calculation is made for a solid flat circular parachute during the period of opening and at steady state.
Download or read book Parachute Stress Analysis During Inflation and at Steady State written by H. G. Heinrich and published by . This book was released on 1963 with total page 35 pages. Available in PDF, EPUB and Kindle. Book excerpt: The stresses occurring in the cloth of a parachute during the period of inflation and under steady state are calculated for a number of instantaneous shapes which are characteristic of the opening process and the steady state. The method is general and may be applied to any type of parachute built out of solid cloth, concentric rings or ribbons. The presented analysis is related to canopies consisting of triangular gores but can be extended to other gore patterns. A numerical calculation is made for a solid flat circular parachute during the period of opening and at steady state. (Author).
Download or read book Parachute Stress Analysis During Inflation and at Steady State written by H. G. Heinrich and published by . This book was released on 1969 with total page 76 pages. Available in PDF, EPUB and Kindle. Book excerpt: During the period from 1965 to 1969, two new methods for stress calculations have been proposed and general remarks primarily concerning the elasticity characteristics of a parachute cloth and pressure distribution have been made. The conservative way of performing a parachute stress snalysis consists of first establishing the geometry of the parachute canopy and then applying a certain pressure distribution. Subsequently, the pressure distribution has been linked to the instantaneous parachute force which can be obtained from an opening shock calculation. In this manner one can possibly obtain closed solutions with a minimum of empirical factors. An example of this approach is presented in detail in the following chapters.
Download or read book AIAA 81 1912 AIAA 81 1952 With omissions in numbering written by and published by . This book was released on 1981 with total page 418 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Change of Pressure Distribution on Parachute Canopies During Inflation written by H.-D. Mlzig and published by . This book was released on 1965 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: For a design engineer strength calculation is a prerequisite for completion of design. The parachute designer however encounters great difficulty. Theory provides no means for calculation and almost no data is available of measurements under dynamic conditions to permit adequate strength calculation. The rapidly changing dynamic forces can vastly exceed the steady state forces. Great efforts have been made to predict stresses in a parachute canopy. The latest work for a parachute stress analysis was conducted by H.G. Heinrich and L.R. Jamison [1] and is a great advance. Contrary to former attempts it includes parachute shapes during inflation of the canopy. The great disadvantage of all theoretical attempts is that the actual stress distribution in a canopy is still unknown. No method has yet been found to measure stresses directly in many parts of a canopy.
Download or read book NASA SP written by and published by . This book was released on 1983 with total page 778 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Wearable Electronics and Photonics written by Xiaoming Tao and published by Elsevier. This book was released on 2005-03-29 with total page 265 pages. Available in PDF, EPUB and Kindle. Book excerpt: Integrating electronics into clothing is a major new concept, which opens up a whole array of multi-functional, wearable electro-textiles for sensing/monitoring body functions, delivering communication facilities, data transfer, individual environment control, and many other applications. With revolutionary advancements occurring at an unprecedented rate in many fields of science and electronics the possibilities offered by wearable technologies are tremendous and widespread. These advancements will transform the world and will soon begin to permeate into commercial products.The first section of the book discusses the materials and devices used in the field, including electro-statically generated nanofibres, electroceramic fibres and composites and electroactive fabrics. It summarizes recent developments in electrically conductive fabric structures and puts together a few theoretical treatments of the electro-mechanical properties of various fabric structures. The next section reviews topics related to wearable photonics such as fibre optic sensors and integrated smart textile structures, the developments in various flexible photonic display technologies as well as looking at current communication apparel and optical fibre fabric displays. Next the book focuses on integrated structures and system architectures. Finally the issues facing a fashion designer working with wearables are explored.Wearable electronics and photonics covers many aspects of the cutting-edge research and development into this exciting field and provides a window through which only a small portion of the exciting emerging technology can be seen. With contributions from a panel of international experts in the field this is an essential guide for all electrical, textile and biomedical engineers as well as academics and fashion designers. - Stay one step ahead of the industry on this hot topic - Evaluates the major new concept of integrating electronics into clothing - Explores future trends for fashion and specialist clothing
Download or read book A Collection of Technical Papers written by and published by . This book was released on 1975 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt:
