Download or read book Stress Intensity Factors in Two Bonded Elastic Layers Containing Cracks Perpendicular to and on the Interface Part 1 written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-08-13 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: The basic crack problem which is essential for the study of subcritical crack propagation and fracture of layered structural materials is considered. Because of the apparent analytical difficulties, the problem is idealized as one of plane strain or plane stress. An additional simplifying assumption is made by restricting the formulation of the problem to crack geometries and loading conditions which have a plane of symmetry perpendicular to the interface. The general problem is formulated in terms of a coupled system of four integral equations. For each relevant crack configuration of practical interest, the singular behavior of the solution near and at the ends and points of intersection of the cracks is investigated and the related characteristic equations are obtained. The edge crack terminating at and crossing the interface, the T-shaped crack consisting of a broken layer and a delamination crack, the cross-shaped crack which consists of a delamination crack intersecting a crack which is perpendicular to the interface, and a delamination crack initiating from a stress-free boundary of the bonded layers are some of the practical crack geometries considered. Lu, M. C. and Erdogan, F. Unspecified Center NASA-CR-159218 NSF ENG-78-09737; NGR-39-007-011...
Download or read book Stress Intensity Factors in Two Bonded Elastic Layers Containing Cracks Perpendicular to and on the Interface Part 1 Analysis written by and published by . This book was released on 1980 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stress Intensity Factors in Two Bonded Elastic Layers Containing Cracks Perpendicular to and on the Interface Part 2 Solution and Results written by and published by . This book was released on 1980 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 652 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fracture Mechanics written by Fazil Erdogan and published by ASTM International. This book was released on 1995 with total page 716 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stress Intensity Factors T Stresses Weight Functions Supplement Volume written by Theo Fett and published by KIT Scientific Publishing. This book was released on 2014-08-13 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stresses in the vicinity of the crack tips are responsible for failure of crack-containing components. The singular stress contribution is characterised by the stress intensity factor K, the first regular stress term is represented by the so-called T-stress. Whereas in the main volume, IKM 50, predominantly one-dimensional cracks were considered in homogeneous materials, this supplement volume compiles new results on one-dimensional and two-dimensional cracks.
Download or read book Recent Research Reports written by National Science Foundation (U.S.). Directorate for Engineering and Applied Science and published by . This book was released on 1979 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1973 with total page 528 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Methods of Mathematical Modelling and Computation for Complex Systems written by Jagdev Singh and published by Springer Nature. This book was released on 2021-08-26 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains several contemporary topics in the areas of mathematical modelling and computation for complex systems. The readers find several new mathematical methods, mathematical models and computational techniques having significant relevance in studying various complex systems. The chapters aim to enrich the understanding of topics presented by carefully discussing the associated problems and issues, possible solutions and their applications or relevance in other scientific areas of study and research. The book is a valuable resource for graduate students, researchers and educators in understanding and studying various new aspects associated with complex systems. Key Feature • The chapters include theory and application in a mix and balanced way. • Readers find reasonable details of developments concerning a topic included in this book. • The text is emphasized to present in self-contained manner with inclusion of new research problems and questions.
Download or read book Recent Advances in Structural Engineering written by and published by Universities Press. This book was released on 2005-02 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains state-of-the-art review articles on specific research areas in the civil engineering discipline-the areas include geotechnical engineering, hydraulics and water resources engineering, and structural engineering. The articles are written by invited authors who are currently active at the international level in their respective research fields.
Download or read book Security and Reliability of Damaged Structures and Defective Materials written by Guy Pluvinage and published by Springer Science & Business Media. This book was released on 2009-07-06 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: Structures that are essential for economy and security such as energy production, transportation and supply, water supply, buildings, are susceptible to failure, because of defects already present in the material, or created at fabrication, or appearing during service. Methods of assesment of the nocivity of these defects are needed, to predict the remaining service life and the eventual emergency of stopping service and repairing, if possible. To reach this objectives, this book presents the last methods derived from the classical linear, non-linear fracture mechanics concepts, including fatigue and notch fracture mechanics. Several examples of structures rehabilitations and repairing are given. This book gathers the presentation made during the Advanced Research Workshop held in Portoroz (Slovenia) in October 2008, under the auspices of NATO Science for Peace and Security Programme. It is edited by Professor Guy Pluvinage from the University Paul Verlaine – Metz (France) and Professor Aleksandar Sedmak from the University of Belgrade, Faculty of Mechanical Engineering. Both have a long and rich experience in analysis of theoretical and practical cases in safety and reliability of structures. Other contributors are all known as experts in the areas of fatigue, facture and reliability of structures.
Download or read book Solution of Crack Problems written by D.A. Hills and published by Springer Science & Business Media. This book was released on 1996-02-29 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is concerned with the numerical solution of crack problems. The techniques to be developed are particularly appropriate when cracks are relatively short, and are growing in the neighbourhood of some stress raising feature, causing a relatively steep stress gradient. It is therefore practicable to represent the geometry in an idealised way, so that a precise solution may be obtained. This contrasts with, say, the finite element method in which the geometry is modelled exactly, but the subsequent solution is approximate, and computationally more taxing. The family of techniques presented in this book, based loosely on the pioneering work of Eshelby in the late 1950's, and developed by Erdogan, Keer, Mura and many others cited in the text, present an attractive alternative. The basic idea is to use the superposition of the stress field present in the unfiawed body, together with an unknown distribution of 'strain nuclei' (in this book, the strain nucleus employed is the dislocation), chosen so that the crack faces become traction-free. The solution used for the stress field for the nucleus is chosen so that other boundary conditions are satisfied. The technique is therefore efficient, and may be used to model the evolution of a developing crack in two or three dimensions. Solution techniques are described in some detail, and the book should be readily accessible to most engineers, whilst preserving the rigour demanded by the researcher who wishes to develop the method itself.
Download or read book Thermal Effects on Structures and Materials written by American Society of Mechanical Engineers. Winter Annual Meeting and published by American Society of Civil Engineers. This book was released on 1990 with total page 128 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fracture Mechanics in Layered and Graded Solids written by Tian Xiaohong and published by Walter de Gruyter GmbH & Co KG. This book was released on 2014-09-23 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechanical responses of solid materials are governed by their material properties. The solutions for estimating and predicting the mechanical responses are extremely difficult, in particular for non-homogeneous materials. Among these, there is a special type of materials whose properties are variable only along one direction, defined as graded materials or functionally graded materials (FGMs). Examples are plant stems and bones. Artificial graded materials are widely used in mechanical engineering, chemical engineering, biological engineering, and electronic engineering. This work covers and develops boundary element methods (BEM) to investigate the properties of realistic graded materials. It is a must have for practitioners and researchers in materials science, both academic and in industry. Covers analysis of properties of graded materials. Presents solutions based methods for analysis of fracture mechanics. Presents two types of boundary element methods for layered isotropic materials and transversely isotropic materials. Written by two authors with extensive international experience in academic and private research and engineering.
Download or read book SPE Production Operations written by and published by . This book was released on 2006 with total page 554 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book JSME International Journal written by and published by . This book was released on 1990 with total page 606 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Continuum Mechanics Aspects of Geodynamics and Rock Fracture Mechanics written by P. Thoft-Christensen and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: During a NATO Advanced Study Institute in Izmir, Tur key, July 1973 on Modern Developments in Engineering Seis mology and Earthquake Engineering it emerged that a debate on Continuum Mechanics Aspects of Geodynamics and Rock Fracture Mechanics would be very welcome. Therefore, it was decided to seek NATO sponsorship for an Advanced Study In stitute on this subject. The purpose of the new Advanced Study Institute was to provide a link between mechanics of continuum media and geo dynamic s. By bringing together a group of leading scientists from the above two fields and participants actively engaged in research and applications in the same fields, it was believed that fruitful discussions could emerge to facilitate an exchange of knowledge, experience and newly-conceived ideas. The Institute aimed primarily at the solution of such problems as connected with the study of stress and strain con ditions in the Earth, generic causes of earthquakes, energy release and focal mechanism and seismic wave propagation in troducing modern methods of continuum and rock fracture mechanics. Secondly to inspire scientists working in continuum mechanics to open new avenues of research connected with the above problems, and seismologists to adapt modern, advanced methods of continuum and rock fracture mechanics to their work.
