Download or read book Stress intensity Factors by Boundary Collocation for Single edge notch Specimens Subject to Splitting Forces written by Bernard Gross and published by . This book was released on 1966 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: A boundary -value-collocation procedure was applied in conjunction with the Williams stress function to determine values of the stress-intensity factor K1 for single-edge cracks in plate specimens subject to splitting forces applied close to the crack and acting transversely to it. The results are presented in terms of the dimensionless quantity Y = K1BH3 /2/pa, where B and H are the specimen thickness and half-depth, a is the effective crack length, and P is the applied load. The results are practically independent of the ratio of effective specimen length to specimen half-depth q/H, when this ratio is not less than a/H + 2, and are then in excellent agreement with those derived by other investigators from compliance measurements. In the limit, as H/a approaches zero, the value of Y approaches that obtained in an elementary analysis which treats the specimen as a pair of built-in cantilever beams.
Download or read book Stress intensity Factors for a Single edge notch Tension Specimen by Boundary Collocation of a Stress Function written by Bernard Gross and published by . This book was released on 1964 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stress intensity Factors for Single edge notch Specimens in Bending Or Combined Bending and Tension by Boundary Collocation of a Stress Function written by Bernard Gross and published by . This book was released on 1965 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: A boundary-value-collocation procedure was used in conjunction with the Williams stress function to determine values of the stress-intensity factor K for single edge cracks of various depths in specimens subjected to pure bending. The results are of use in connection with K(sub Ic) fracture toughness tests, which utilize rectangular-section crack-notch beam specimens loaded in four-point bending, and are in good agreement with published results derived from experimental compliance measurements. The results are expressed in convenient, compact form in terms of the dimensionless quantity Y(exp 2)=K(exp 2)B(exp 2)W(exp 3)/M(exp 2), which is a function of relative crack depth a/W only, where B and W are the specimen width and thickness and M is the applied bending moment. On the assumption that the condition for a valid K(sub Ic) test is that the maximum nominal stress at the crack tip should not exceed the yield strength of the material, the K(sub Ic) measurement capacity of bend specimens was estimate as a function of a/W. The measurement capacity is proportional to the yield strength and to the square root of the specimen depth, and it is greatest for a/W in the range 0.2 to 0.3. Values of K for single-edge-notch specimens subjected to combined bending and tension were obtained by superposition of the present results and those of earlier work for specimens loaded in uniform tension. These values are of interest in connection with the use of single-edge-notch specimens that are off-center pin-loaded in tension. It is shown that the K(sub Ic) measurement capacity of such specimens is not very sensitive to the eccentricity of loading.
Download or read book NASA Technical Note written by and published by . This book was released on 1970 with total page 418 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stress intensity Factor Calculations Using the Boundary Force Method written by and published by . This book was released on 1987 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Selected Listing of NASA Scientific and Technical Reports for 1966 written by United States. National Aeronautics and Space Administration. Scientific and Technical Information Division and published by . This book was released on 1967 with total page 2084 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1976 with total page 978 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Monthly Catalog of United States Government Publications written by United States. Superintendent of Documents and published by . This book was released on 1966 with total page 1464 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book NASA Scientific and Technical Reports written by United States. National Aeronautics and Space Administration Scientific and Technical Information Division and published by . This book was released on 1967 with total page 2300 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Selected Listing of NASA Scientific and Technical Reports for written by United States. National Aeronautics and Space Administration. Scientific and Technical Information Division and published by . This book was released on 1964 with total page 1156 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A General Introduction to Fracture Mechanics written by Institution of Mechanical Engineers (Great Britain) and published by SAE International. This book was released on 1978 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fracture Mechanics written by Nicholas Perrone and published by . This book was released on 1978 with total page 744 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Journal of Testing and Evaluation written by and published by . This book was released on 1997 with total page 262 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Selected Papers on Crack Tip Stress Fields written by Robert Joseph Sanford and published by . This book was released on 1997 with total page 688 pages. Available in PDF, EPUB and Kindle. Book excerpt: Topics in this volume include: Westergaard stress functions for severe periodic crack problems; the stress intensity factors and crack profiles for centre and edge cracks in plates subject to arbitrary stesses; and central crack in plane ortotropic rectangular sheet.
Download or read book Plane Elastostatic Analysis of V notched Plates written by Bernard Gross and published by . This book was released on 1970 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Government wide Index to Federal Research Development Reports written by and published by . This book was released on 1966-09 with total page 732 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Some Plane Problem Elastostatic Solutions for Plates Having a V notch written by Bernard Gross and published by . This book was released on 1970 with total page 768 pages. Available in PDF, EPUB and Kindle. Book excerpt: