EBookClubs

Read Books & Download eBooks Full Online

EBookClubs

Read Books & Download eBooks Full Online

Book Statistical Analysis of Tensile Properties of Heat treated Ti 4A1 3Mo 1V Sheet

Download or read book Statistical Analysis of Tensile Properties of Heat treated Ti 4A1 3Mo 1V Sheet written by H. R. Ogden and published by . This book was released on 1960 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Statistical Analysis of Tensile Properties of Heat treated Ti 4A1 3Mo 1V and Ti 2 5A1 16V Sheet

Download or read book Statistical Analysis of Tensile Properties of Heat treated Ti 4A1 3Mo 1V and Ti 2 5A1 16V Sheet written by G. H Beatty and published by . This book was released on 1961 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: IN THE SOLUTION TREATED AND AGED CONDITION, Ti4Al-3Mo-1V has a higher ultimate strength than does Ti-2.5Al-16V, but the two alloys are about even in yield strength and elongation. In the solution-treated condition, Ti-4Al-3Mo-1V is unquestionably stronger than Ti-2.5Al-16V. These conclusions are independent of producer. There is not much difference in the same alloy produced by different companies. The alloys developed under the Titanium-Alloy Sheet-Rolling Program would not endure the most critical interpretation of release property specifications. On the other hand, these alloys come reasonably close to specifications. A complete set of release property specifications is available only for specimens that have been solution treated and aged. Such specimens do not all exhibit the desired ultimate and yield strength, but the percentage of rejects is small enough to be encouraging. (Author).

Book Control of Dimensions in High strength Heat treated Steel Parts

Download or read book Control of Dimensions in High strength Heat treated Steel Parts written by A. R. Elsea and published by . This book was released on 1961 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt: THE ACHIEVEMENT AND MAINTENANCE OF DESIRED DIMENSIONS IN COMPLEX, PRECISION-BUILT STRUCTURES, SUCH AS ROCKET-MOTOR CASES, ARE CRITICAL AND TECHNICALLY INVOLVED PROBLEMS. Their proper functioning demands close dimensional tolerances. Dimensional stability is extremely difficult toACHIEVE IN STEELS AT ULTRAHIGH STRENGTH LEVELS. The problem stems from interacting metallurgical factors which manifest themselves in volumetric and shape changes. The principal sources of size change are the changes in specific volume accompanying the phase transformations which occur in hardening and tempering. Distortion occurs when a part deforms in response to stress. The problem of dimensional instability is analyzed, the factors involved are discussed, and recommendations are made regarding the control of these factors. (Author).

Book The Mechanical Properties of the 18 Per Cent Nickel Maraging Steels

Download or read book The Mechanical Properties of the 18 Per Cent Nickel Maraging Steels written by J. E. Campbell and published by . This book was released on 1964 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the combination of tensile properties and toughness that can be obtained with the maraging steels is higher than can be achieved with other steels by simple heat treatments, there is considerable interest in using the maraging steels for critical components such as rocket motor cases, pressure vessels, and aircraft forgings. This report includes information on the tensile, compressive, shear, bearing, dynamic modulus, impact, bend, fatigue, creep, and rupture properties of the 18 per cent nickel maraging steels and on the effect of temperature on these properties. Data for the properties of sheet, bar, and forgings, as well as data illustrating the effect of cold rolling, variation in the heat treatment, and elevated-temperature exposure also are presented. Data on the effect of specimen orientation, which are also included, indicate that the ductility and toughness of specimens designed to evaluate the properties in the short transverse direction are somewhat lower than in the other directions. The high strength and toughness that can be obtained in the 18 per cent nickel maraging steels make them attractive for certain critical applications that require these properties. The fabrication characteristics, weldability, and simple heat treatment are other advantages of these steels. (Author).

Book Thermal Radiative Properties of Selected Materials

Download or read book Thermal Radiative Properties of Selected Materials written by W. D. Wood and published by . This book was released on 1962 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book The Effect of Fabrication History and Microstructure on the Mechanical Properties of Refractory Metals and Alloys

Download or read book The Effect of Fabrication History and Microstructure on the Mechanical Properties of Refractory Metals and Alloys written by Albert G. Imgram and published by . This book was released on 1963 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes the present knowledge concerning the relationship among fabrication history, metallurgical structure, and the mechanical properites of the refractory metals columbium, tantalum, bolybdenum, and tungsten, and their alloys. These are the refractory metals currently reveiveing the most attention for aerospace applications, and are therefore the materials considered in this survey. The report is organized into three main sections, titled ''Fabrication'', ''Microstructure and Alloying'', and ''Interstitial Impurities''. The data presented were selected as those which best illustrate the topics discussed. Descriptions of the metaljurgical principles involved are included. Suggestions for optimizing mechanical properties by controlling metallurgical structure are made where possible. (Author).

Book The Status and Properties of Titanium Alloys for Thick Plate

Download or read book The Status and Properties of Titanium Alloys for Thick Plate written by G. E. Faulkner and published by . This book was released on 1963 with total page 60 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Summary of the Seventh Meeting of the Refractory Composites Working Group

Download or read book Summary of the Seventh Meeting of the Refractory Composites Working Group written by W. A. Gibeaut and published by . This book was released on 1963 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes information on refractory composites for use above 2500 F, as presented at the Seventh Meeting of the Refractory Composites Working Group, held March 12-14, 1963. Reports presented at the meeting were concerned with pro tective coatings, insulating ceramics, materials for rocket thrust chambers, dispersion strength ening of metals, joining of refractory materials, and testing techniques. Emphasis in the field of coatings for refractory metals has shifted from the rudiments of developing oxidation-resistant coatings to improvement and advanced evaluation of coatings to predict their utility for re-entry vehicles. (Author).

Book Summary of the Fifth Meeting of the Refractory Composites Working Group

Download or read book Summary of the Fifth Meeting of the Refractory Composites Working Group written by William D. Klopp and published by . This book was released on 1962 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Summary of the Sixth Meeting of the Refractory Composites Working Group

Download or read book Summary of the Sixth Meeting of the Refractory Composites Working Group written by W. A. Gibeaut and published by . This book was released on 1962 with total page 94 pages. Available in PDF, EPUB and Kindle. Book excerpt: I NFORMATION ON REFRACTORY COMPOSITES FOR USE ABOVE

Book A Summary of the Theory of Fracture in Metals

Download or read book A Summary of the Theory of Fracture in Metals written by J. W. Spretnak and published by . This book was released on 1961 with total page 70 pages. Available in PDF, EPUB and Kindle. Book excerpt: The theoretical strength of metals, bas d on atomic forces, is in the order of 100 to 1000 greater than that observed. Reasons for this discrepancy are discussed in detail, but the more important ones are (1) lattice imperfections, (2) the fact th t real metals ar polycrystalline aggregates, (3) crystalline anisotropy, and (4) the ability of metals to deform by shear. Plastic flow, particularly heterogeneous plastic flow, is intimately associated with crack initiation. The precise conditions under which plastic flow c ase and bond rupturing (cracking begins are not completely understood. The body-centered cubic lattice has geometric characteristics that make it particularly susceptible to fracture with little or no preceding plastic flow. Multidirectional stress fields, both microscopic and macroscopic, affect the degree of plastic deformation that precedes crack initiation. The theory of fracture as it exists oday is reviewed. (Author).

Book Department of Defense Refractory Metals Sheet rolling Program

Download or read book Department of Defense Refractory Metals Sheet rolling Program written by H. R. Ogden and published by . This book was released on 1961 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt: A summary is presented of the status of the Department of Defense Refractory Metals SheetRolling Program to accelerate the development of production techniques for high-quality, consistent sheet products from the refractory metals (Nb, Mo, Ta, and W) and their alloys. The program includes: (1) development of sheet production techniques, (2) establishment of minimum data re uired to evaluate mill production, (3) evaluation of fabrication characteristics of the sheet produced, and (4) establishment of design data. Contracts were awarded for the development of sheet production techniques for all four refractory metals. One contract was awarded for the evaluation of Mo alloy sheet fabrication characteristics. (Author).

Book Status Report No  2 on Department of Defense Refractory Metals Sheet rolling Program

Download or read book Status Report No 2 on Department of Defense Refractory Metals Sheet rolling Program written by H. R. Ogden and published by . This book was released on 1962 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Nb program is nearing completion of laboratory tory rolling studiory materials, *Heat resistant alloys, *Sheets, Niobium alloys, Molybdenum alloys, Tantalum alloys, Tungsten alloys, Titanium alloys, Zirconium alloys, Tungsten, Powder metallurgy, Electric arcs, Manufacturing methods, Mechanical proper ies, Forging, Heat treatment, Melting, Extrusion, Deformation, Hardness, Rolling mills, Processing. Identifiers: Floturning. The Nb program is nearing completion of laboratory tory rolling studies, and a single composition for larger scale rolling studies will be selected in the near future. In the Mo program, it has been shown that true hot forging of billets to sheet bar results in higher recrystallization temperatures of TZM and Mo-0.5Ti sheet than are obtained when normal forging temperatures are used. The Ta program is in the early stages of ingot production and primary breakdown fabrication of the Ta-30Nb-7.5V alloy. Three methods of fabricating W sheet are being investigated: rolling of powder-metallurgy billets, fabrication of arc-melted ingots, and floturning of cylindrical blanks. Properties obtained on both powdermetallurgy and arc-melted tungsten sheet compare very favorably. Evaluation of the formability of Mo-alloy sheet has been delayed until sheet is available from the production program. (Author).

Book The Engineering Properties of Tungsten and Tungsten Alloys

Download or read book The Engineering Properties of Tungsten and Tungsten Alloys written by F. F. Schmidt and published by . This book was released on 1963 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: The results of a state-of-the-art survey covering tungsten and ten of its alloys are presented. All data are given in tabular and graphical form covering some of the more important physical, mechanical, and metallurgical properties for each material. References are given at the conclusion of each material section.

Book The Engineering Properties of Molybdenum and Molybdenum Alloys

Download or read book The Engineering Properties of Molybdenum and Molybdenum Alloys written by F. F. Schmidt and published by . This book was released on 1963 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: