Download or read book Stability of Parallel Two phase Flow written by Paulus Alphonsus Maria Boomkamp and published by . This book was released on 1998 with total page 155 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stability of Two phase Flow in Heated Parallel Channels written by Albert Carnesale and published by . This book was released on 1965 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A New Method for Determining the Stability of Two phase Flow in Parallel Heated Channels with Applications to Nuclear Reactors written by J. H. Bick and published by . This book was released on 1960 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Stability of Two phase Flow Water air in Parallel Pipes with Common Feed written by Ludmila Pustylnik and published by . This book was released on 2007 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Encyclopedia of Two Phase Heat Transfer and Flow IV written by John R Thome and published by World Scientific Publishing. This book was released on 2018-05-18 with total page 1372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Set IV is a new addition to the previous Sets I, II and III. It contains 23 invited chapters from international specialists on the topics of numerical modeling of pulsating heat pipes and of slug flows with evaporation; lattice Boltzmann modeling of pool boiling; fundamentals of boiling in microchannels and microfin tubes, CO2 and nanofluids; testing and modeling of micro-two-phase cooling systems for electronics; and various special topics (flow separation in microfluidics, two-phase sensors, wetting of anisotropic surfaces, ultra-compact heat exchangers, etc.). The invited authors are leading university researchers and well-known engineers from leading corporate research laboratories (ABB, IBM, Nokia Bell Labs). Numerous 'must read' chapters are also included here for the two-phase community. Set IV constitutes a 'must have' engineering and research reference together with previous Sets I, II and III for thermal engineering researchers and practitioners.
Download or read book Stability of Parallel Flows written by R. Betchov and published by Elsevier. This book was released on 2012-12-02 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: Stability of Parallel Flows provides information pertinent to hydrodynamical stability. This book explores the stability problems that occur in various fields, including electronics, mechanics, oceanography, administration, economics, as well as naval and aeronautical engineering. Organized into two parts encompassing 10 chapters, this book starts with an overview of the general equations of a two-dimensional incompressible flow. This text then explores the stability of a laminar boundary layer and presents the equation of the inviscid approximation. Other chapters present the general equations governing an incompressible three-dimensional flow, which requires the massive use of a computer. This book discusses as well the experimental studies on the oscillations of the boundary layer wherein the mean flow is affected by the presence of oscillations. The final chapter describes the concept of the stability of turbulent flows found in boundary layers, wakes, and jets. This book is a valuable resource for physicists, mathematicians, engineers, scientists, and researchers.
Download or read book Two Phase Flow Phase Change and Numerical Modeling written by Amimul Ahsan and published by BoD – Books on Demand. This book was released on 2011-09-26 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt: The heat transfer and analysis on laser beam, evaporator coils, shell-and-tube condenser, two phase flow, nanofluids, complex fluids, and on phase change are significant issues in a design of wide range of industrial processes and devices. This book includes 25 advanced and revised contributions, and it covers mainly (1) numerical modeling of heat transfer, (2) two phase flow, (3) nanofluids, and (4) phase change. The first section introduces numerical modeling of heat transfer on particles in binary gas-solid fluidization bed, solidification phenomena, thermal approaches to laser damage, and temperature and velocity distribution. The second section covers density wave instability phenomena, gas and spray-water quenching, spray cooling, wettability effect, liquid film thickness, and thermosyphon loop. The third section includes nanofluids for heat transfer, nanofluids in minichannels, potential and engineering strategies on nanofluids, and heat transfer at nanoscale. The forth section presents time-dependent melting and deformation processes of phase change material (PCM), thermal energy storage tanks using PCM, phase change in deep CO2 injector, and thermal storage device of solar hot water system. The advanced idea and information described here will be fruitful for the readers to find a sustainable solution in an industrialized society.
Download or read book Two phase Flow Stability and Dryout in Parallel Channels in Natural Circulation written by and published by . This book was released on 1993 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Encyclopedia Of Two phase Heat Transfer And Flow I Fundamentals And Methods A 4 volume Set written by John R Thome and published by World Scientific. This book was released on 2015-08-14 with total page 1109 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of the two-set series is to present a very detailed and up-to-date reference for researchers and practicing engineers in the fields of mechanical, refrigeration, chemical, nuclear and electronics engineering on the important topic of two-phase heat transfer and two-phase flow. The scope of the first set of 4 volumes presents the fundamentals of the two-phase flows and heat transfer mechanisms, and describes in detail the most important prediction methods, while the scope of the second set of 4 volumes presents numerous special topics and numerous applications, also including numerical simulation methods.Practicing engineers will find extensive coverage to applications involving: multi-microchannel evaporator cold plates for electronics cooling, boiling on enhanced tubes and tube bundles, flow pattern based methods for predicting boiling and condensation inside horizontal tubes, pressure drop methods for singularies (U-bends and contractions), boiling in multiport tubes, and boiling and condensation in plate heat exchangers. All of these chapters include the latest methods for predicting not only local heat transfer coefficients but also pressure drops.Professors and students will find this 'Encyclopediaa of Two-Phase Heat Transfer and Flow' particularly exciting, as it contains authored books and thorough state-of-the-art reviews on many basic and special topics, such as numerical modeling of two-phase heat tranfser and adiabatic bubbly and slug flows, the unified annular flow boiling model, flow pattern maps, condensation and boiling theories, new emerging topics, etc.
Download or read book Advances in Multi fluid Flows written by Yuriko Y. Renardy and published by SIAM. This book was released on 1996-01-01 with total page 452 pages. Available in PDF, EPUB and Kindle. Book excerpt: The papers from this conference deal with multi-fluid flows and interfacial instabilities. Papers on multiple-layer convection, wave dynamics in viscous flows, stability of viscoelastic flows, numberical computation of bubbles, and solidification are included.
Download or read book Coolant Flow Instabilities in Power Equipment written by Vladimir B. Khabensky and published by CRC Press. This book was released on 2012-12-17 with total page 391 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal-hydraulic instability can potentially impair thermal reliability of reactor cores or other power equipment components. Thus it is important to address stability issues in power equipment associated with thermal and nuclear installations, particularly in thermal nuclear power plants, chemical and petroleum industries, space technology, and radio, electronic, and computer cooling systems. Coolant Flow Instabilities in Power Equipment synthesizes results from instability investigations around the world, presenting an analysis and generalization of the published technical literature. The authors include individual examples on flow stability in various types of equipment, including boilers, reactors, steam generators, condensers, heat exchangers, turbines, pumps, deaerators, bubblers, and pipelines. They also present information that has not been widely available until recently, such as thermal-acoustic instability, flow instability with supercritical parameters, and single-phase coolant flow static instability. The material described in this book is derived from vast amounts of experimental data from thermal-physical test facilities and full-scale installations. It is presented in a manner accessible to readers without advanced mathematical backgrounds. Particular attention has been paid to oscillatory (low-frequency and thermal-acoustic) and static thermal-hydraulic coolant flow instability. In addition, the physical mechanism of instability has been considered in detail. This book provides knowledge of the various types of flow instability, the equipment where this instability can manifest, and the ensuing consequences, as well as makes recommendations concerning possible removal or mitigation of these consequences. The authors provide this information as a useful reference for readers to facilitate the enhanced safety of modern power equipment through qualitative evaluation of design and flow parameters and subsequent selection of the optimal means for increasing flow stability.
Download or read book Laminar Flow Forced Convection in Ducts written by R. K. Shah and published by Academic Press. This book was released on 2014-06-28 with total page 492 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laminar Flow Forced Convection in Ducts is a sourcebook for compact heat exchanger analytical data. This book describes the analytical solutions for laminar fluid flow and forced convection heat transfer in circular and noncircular pipes, including applicable differential equations and boundary conditions involving velocity and temperature problems of fluid flow. The book also discusses fluid flow—how much power is required to pump fluids through the heat exchanger, as well as the heat transfer—the determination of q" distribution, and the temperature of fluid and walls. The text also analyzes the coolant or heat transfer fluid flows in a nuclear power reactor composed of a bundle of circular section fuel rods located inside a round tube. R.A. Axford addresses fluid flow and heat transfers results for the rod bundle geometry in "Heat Transfer in Rod Bundles." The book also provides an overview and guidelines that can be used for the designer and the applied mathematician. This book is suitable for engineers working in electronics, aerospace, instrumentation, and biomechanics that use cooling or heating exchanges or solar collection systems.
Download or read book Boiling Heat Transfer And Two Phase Flow written by L S Tong and published by Routledge. This book was released on 2018-05-04 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: Completely updated, this graduate text describes the current state of boiling heat transfer and two-phase flow, in terms through which students can attain a consistent understanding. Prediction of real or potential boiling heat transfer behaviour, both in steady and transient states, is covered to aid engineering design of reliable and effective systems.
Download or read book Two phase Flow Instability and Dryout in Parallel Channels in Natural Circulation written by and published by . This book was released on 1993 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt: The unique feature of parallel channel flows is that the pressure drop or driving head for the flow is maintained constant across any given channel by the flow in all the others, or by having a large downcomer or bypass in a natural circulation loop. This boundary condition is common in all heat exchangers, reactor cores and boilers, it is well known that the two-phase flow in parallel channels can exhibit both so-called static and dynamic instability. This leads to the question of the separability of the flow and pressure drop boundary conditions in the study of stability and dryout. For the areas of practical interest, the flow can be considered as incompressible. The dynamic instability is characterized by density (kinematic) or continuity waves, and the static instability by inertial (pressure drop) or manometric escalations. The static has been considered to be the zero-frequency or lowest mode of the dynamic case. We briefly review the status of the existing literature on both parallel channel static and dynamic instability, and the latest developments in theory and experiment. The difference between the two derivations lies in the retention of the time-dependent terms in the conservation equations. The effects and impact of design options are also discussed. Since dryout in parallel systems follows instability, it has been traditional to determine the dryout power for a parallel channel by testing a single channel with a given (inlet) flow boundary condition without particular regard for the pressure drop. Thus all modern dryout correlations are based on constant or fixed flow tests, a so-called hard inlet, and subchannel and multiple bundle effects are corrected for separately. We review the thinking that lead to this approach, and suggest that for all multiple channel and natural circulation systems close attention should be paid to the actual (untested) pressure drop conditions. A conceptual formulation is suggested as a basis for discussion.
Download or read book Advances in Two Phase Flow and Heat Transfer written by Sadik Kakaç and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 459 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the past two decades, two-phase flow and heat transfer problems associated with two-phase phenomena have been a challenge to many investigators. Two-phase flow applications are found in a wide range of engineering systems, such as nuclear and conventional power plants, evaporators of refrigeration systems and a wide vari ety of evaporative and condensive heat exchangers in the chemical industry. This publication is based on the invited lectures presented at the NATO Advanced Research Workshop on the Advances in Two-Phase Flow and Heat Transfer. The Horkshop was attended by more than 50 leading scientists and practicing engineers who work actively on two-phase flow and heat transfer research and applications in dif ferent sectors (academia, government, industry) of member countries of NATO. Some scientific leaders and experts on the subject matter from the non-NATO countries were also invited. They convened to discuss the state-of-the-art in two-phase flow and heat transfer and formulated recommendations for future research directions. To achieve these goals, invited key papers and a limited number of contributions were presented and discussed. The specific aspects of the subject were treated in depth in the panel sessions, and the unresolved problems identified. Suitable as a practical reference, these volumes incorporate a systematic approach to two-phase flow analysis.
Download or read book Single phase Two phase and Supercritical Natural Circulation Systems written by Pallippattu Krishnan Vijayan and published by Woodhead Publishing. This book was released on 2019-06-19 with total page 650 pages. Available in PDF, EPUB and Kindle. Book excerpt: Single-Phase, Two-Phase and Supercritical Natural Circulation Systems provides readers with a deep understanding of natural circulation systems. This book equips the reader with an understanding on how to detect unstable loops to ensure plant safety and reliability, calculate heat transport capabilities, and design effective natural circulation loops, stability maps and parallel channel systems. Each chapter begins with an introduction to the circulation system before discussing each element in detail and analyzing its effect on the performance of the system. The book also presents thermosyphon heat transport devices in nuclear and other industrial plants, a common information need for students and researchers alike. This book is invaluable for engineers, designers, operators and consultants in nuclear, mechanical, electrical and chemical disciplines. Presents single-phase, two-phase and supercritical natural circulation systems together in one resource to fill an existing knowledge gap Guides the reader through relevant processes, such as designing, analyzing and generating stability maps and natural circulation loops, calculating heat transport capabilities, and maintaining natural circulation system operations Includes global case studies and examples to increase understanding, along with important IAEA standards and procedures
Download or read book Two Phase Flow Heat Exchangers written by Sadik Kakaç and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 1090 pages. Available in PDF, EPUB and Kindle. Book excerpt: Two-phase flow heat exchangers are vital components of systems for power generation, chemical processing, and thermal environment control. The art and science of the design of such heat exchangers have advanced considerably in recent years. This is due to better understanding of the fundamentals of two-phase flow and heat transfer in simple geometries, greater appreciation of these processes in complex goemetries, and enhanced predictive capability through use of complex computer codes. The subject is clearly of great fundamental and practical importance. The NATO ASIan Thermal-Hydraulic Fundamentals and Design of Two-Phase Flow Heat Exchangers was held in Povoa de Varzim (near Porto), Portugal, July 6-17, 1987. participating in the organization of" the ASI were the Department of Mechanical Engineering and the Clean Energy Research Institute, University of Miami; Universidade do Porto; and the Department of Mechanical Engineering, Aeronautical Eng ineer ing, and Mechanics, Rensselaer Polytechnic Institute. The ASI was arranged primarily as a high-level teaching activity by experts representing both academic and industrial viewpoints. The program included the presentation of invited lectures, a limited number of related technical papers and discussion sessions.
