Download or read book SP 315 ACI fib International Symposium on Punching Shear in Structural Concrete Slabs written by Carlos E. Ospina and published by . This book was released on 2017-07-28 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Punching shear of structural concrete slabs written by FIB - Féd. Int. du Béton and published by FIB - Féd. Int. du Béton. This book was released on 2017 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: fib Bulletin 81 reports the latest information available to researchers and practitioners on the analysis, design and experimental evidence of punching shear of structural concrete slabs. It follows previous efforts by the International Federation for Structural Concrete (fib) and its predecessor the Euro-International Committee for Concrete (CEB), through CEB Bulletin 168, Punching Shear in Reinforced Concrete (1985) and fibBulletin 12, Punching of structural concrete slabs (2001), and an international symposium sponsored by the punching shear subcommittee of ACI Committee 445 (Shear and Torsion) and held in Kansas City, Mo., USA, in 2005. This bulletin contains 18 papers that were presented in three sessions as part of an international symposium held in Philadelphia, Pa., USA, on October 25, 2016. The symposium was co-organized by the punching shear sub-committee of ACI 445 and by fib Working Party 2.2.3 (Punching and Shear in Slabs) with the objectives of not only disseminating information on this important design subject but also promoting harmonization among the various design theories and treatment of key aspects of punching shear design. The papers are organized in the same order they were presented in the symposium. The symposium honored Professor Emeritus Neil M. Hawkins (University of Illinois at Urbana-Champaign, USA), whose contributions through the years in the field of punching shear of structural concrete slabs have been paramount. The papers cover key aspects related to punching shear of structural concrete slabs under different loading conditions, the study of size effect on punching capacity of slabs, the effect of slab reinforcement ratio on the response and failure mode of slabs, without and with shear reinforcement, and its implications for the design and formulation in codes of practice, an examination of different analytical tools to predict the punching shear response of slabs, the study of the post-punching response of concrete slabs, the evaluation of design provisions in modern codes based on recent experimental evidence and new punching shear theories, and an overview of the combined efforts undertaken jointly by ACI 445 and fib WP 2.2.3 to generate test result databanks for the evaluation and calibration of punching shear design recommendations in North American and international codes of practice.

Download or read book Punching shear in reinforced concrete state of the art report written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 1985-01-01 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Punching Shear in Reinforced Concrete Slabs written by Maria Anna Polak and published by . This book was released on 2005 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Shear and Punching Shear in RC and FRC Elements written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2010-12-01 with total page 274 pages. Available in PDF, EPUB and Kindle. Book excerpt: fib Bulletin 57 is a collection of contributions from a workshop on "Recent developments on shear and punching shear in RC and FRC elements", held in Salò, Italy, in October 2010. Shear is one of a few areas of research into fundamentals of the behaviour of concrete structures where contention remains amongst researchers. There is a continuing debate between researchers from a structures perspective and those from a materials or fracture mechanics perspective about the mechanisms that enable the force flow through a concrete member and across cracks. In 2009, a Working Group was formed within fib Task Group 4.2 "Ultimate Limit State Models" to harmonise different ideas about design procedures for shear and punching. An important outcome of this work was the ensuing discussions between experts and practitioners regarding the shear and punching provisions of the draft fib Model Code, which led to the organization of the Salò workshop. Invited experts in the field of shear and FRC gave 18 lectures at the workshop that was attended by 72 participants from 12 countries in 3 different continents. The contributions from this conference as compiled in this bulletin are believed to represent the best of the current state of knowledge. They certainly are of general interest to fib members and especially helpful in the finalization of the 2010 fibModel Code. It is hoped that this publication will stimulate further research in the field, to refine and harmonize the available analytical models and tools for shear and punching design.

Download or read book 12th PhD Symposium in Prague Czech Rep written by FIB – International Federation for Structural Concrete and published by FIB - Féd. Int. du Béton. This book was released on 2018-08-01 with total page 1312 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Towards a rational understanding of shear in beams and slabs written by fib Fédération internationale du béton and published by FIB - Féd. Int. du Béton. This book was released on 2018-05-01 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reliable performance of beams and slabs in shear is essential for the safety and also for the serviceability of reinforced concrete structures. A possible failure in shear is usually a brittle failure, which underlines the importance of the correct specification of the load carrying capacity in shear. The knowledge of performance in shear is steadily developing and it is now obvious that older structures were not always designed in accordance with contemporary requirements. The increasing load – mainly on bridges – requires the assessment of existing structures, often followed by their strengthening. An appropriate understanding of actual performance of concrete structures in shear is therefore of primary interest. The workshop which was held in Zürich in 2016 brought together a significant number of outstanding specialists working in the field of shear design, who had a chance to exchange their opinions and proposals for improving the current knowledge of shear behaviour in beams and slabs. The specialists came from different parts of the world, which made the workshop general and representative. The workshop was organised by fib Working Party 2.2.1 “Shear in Beams” (convened by O. Bayrak), which is a part of fib Commission 2 "Analysis and Design". Individual contributions mainly address shear in beams with low transversal reinforcement. It is crucial because many existing structures lack such reinforcement. Different theories, e.g. Critical Shear Crack Theory (CSCT), Modified Compression Field Theory (MCFT), Multi-Action Shear Model (MASM), etc. were presented and compared with procedures used in selected national codes or in the fib Model Code 2010. The models for shear design were often based to a great extent on empirical experience. The refined presented models tend to take into account the physical mechanisms in structures more effectively. A brittle behaviour in shear requires not only to check the equilibrium and failure load, but also to follow the progress of failure, including the crack development and propagation, stress redistribution, etc. The significance of the size effect – which causes the nominal strength of a large structure to be smaller than that of a small structure – was pointed out. Nowadays, the fibre reinforcement is used more than before since it allows significant labour costs savings in the construction industry. The contribution of fibres is suitable for shear transfer. It is very convenient that not only ordinary fibre reinforced elements were addressed but also the UHPFRC beams. The production of this new material is indeed growing, while the development of design recommendations has not been sufficiently fast. Fatigue resistance of structures with low shear reinforcement is also an important issue, which was also addressed in this bulletin. It cannot be neglected in prestressed bridges, which are exposed to dynamic loads. A comprehensive understanding of the shear behaviour is necessary. Although many laboratory experiments are carried out, they are suitable only to a limited extent. New testing methods are being developed and show promising results, e.g. digital image correlation. An actual structure performance should rather be tested on a large scale, ideally on real structures under realistic loading conditions.ii The papers presented in the bulletin are a basis for the discussion in view of the development of updated design rules for the new fib Model Code (MC2020), which is currently under preparation. fib Bulletins like this one, dealing with shear, help to transfer knowledge from research to design practice. The authors are convinced that it will lead to better new structures design of as well as to savings and to a safety increase in older existing structures, whose future is often decided now.

Download or read book Fibre Reinforced Concrete written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2022-11-01 with total page 461 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fibre Reinforced Concrete (FRC) is a composite material characterized by an enhanced post-cracking tensile residual strength, due to the capacity of fibres to bridge the crack faces by means of pull-out mechanism. Due to a better knowledge of FRC and the recent developments worldwide of guidelines for structural design, the fib Special Activity Group 5, who prepared the new fib Model Code, decided to introduce some sections on new materials and in particular on FRC structural design. At that time, working Groups TG 8.3 (“Fibre reinforced concrete”) and TG 8.6 (“Ultra high performance fibre reinforced concrete”) of fib prepared these sections of the new fib Model Code concerning FRC design rules for providing a guidance to engineers to properly and safely design FRC structural elements, both at serviceability and at ultimate limit states, based on the state-of-the-art knowledge. This bulletin was written with the aim to share the main framework used by the two groups to introduce these two sections and to describe the many aspects already known, but not yet introduced in the Model Code. Even though the basic principles introduced in the two sections are mainly obtained from research on steel fibre reinforced concrete, the Model Code is open to every type of fibres, following a performance-based design approach. The bulletin represents a wide effort made by the people of the Task Group 4.1 and 4.2 to trace the knowledge on FRC and aims to be helpful for structural designers when using this new material in the practice.

Download or read book Externally applied FRP reinforcement for concrete structures written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2019-05-01 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: In December 1996, CEB established a Task Group with the main objective to elaborate design guidelines for the use of FRP reinforcement in accordance with the design format of the CEB-FIP Model Code and Eurocode2. With the merger of CEB and FIP into fib in June 1998, this Task Group became fib TG 9.3 FRP Reinforcement for concrete structures in Commission 9 Reinforcing and Prestressing Materials and Systems. Finally, as a result of the restructuring of fib’s Commissions and Task Groups at the end of 2014, the Task Group became fib T5.1 FRP Reinforcement for concrete structures, chaired by Stijn Matthys at Ghent University, in Commission 5 Reinforcements. The work of former TG 9.3 and current T5.1 was performed by two working parties (WP), one of which is “Externally Applied Reinforcement” (EAR), which produced fib bulletin 14 “Externally bonded FRP reinforcement for RC structures” in July 2001. Following a number of years of relatively slow activity, the WP on externally applied reinforcement was reactivated and started working on an update of bulletin 14. The result of this work is summarised in the present technical report, which aims to give design guidelines on the use of externally applied FRP reinforcement (both externally bonded and near-surface mounted) for concrete structures. An attempt has been made to present some of the topics in a Eurocode-compatible format, so that the material covered may form the basis for the introduction of composites in the next version of Eurocode 2 and for the updating of the text on seismic retrofitting with composites in the next version of Eurocode 8. All persons who participated in the preparation of this Bulletin are mentioned in the copyright page. Further acknowledgements are due to Josée Bastien (Canada), Hans Rudolf Ganz (Switzerland) and Luc Taerwe (Belgium) for revision of the document. To all members of the working party on externally applied reinforcement our sincere thanks are expressed for the high quality and extensive work brought in on a voluntary basis.

Download or read book Guidelines for Submerged Floating Tube Bridges written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2020-10-01 with total page 131 pages. Available in PDF, EPUB and Kindle. Book excerpt: This bulletin is a guidelines document for “Submerged Floating Tube Bridges”, that represents an innovation in Marine Concrete Structures. This theme is considered important for Commission 1 since in the future several applications are forecast in marine environments. Submerged Floating Tube Bridges are a solution that can be proposed to solve different problems in passing water constrains as lakes and fiords, reducing the impact and allowing several economic advantages. The guidelines certainly will boost the application of Submerged Floating Tube Bridges since the document is useful not only for designers but also for construction companies, owners and public administrations. As guidelines, the bulletin gives wide information on the design, construction and management of these structures, allowing all the users to be confident in promoting the use of Submerged Floating Tube Bridges.

Download or read book Fibre Reinforced Concrete From Design to Structural Applications written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2020-08-01 with total page 555 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first international FRC workshop supported by RILEM and ACI was held in Bergamo (Italy) in 2004. At that time, a lack of specific building codes and standards was identified as the main inhibitor to the application of this technology in engineering practice. The workshop aim was placed on the identification of applications, guidelines, and research needs in order for this advanced technology to be transferred to professional practice. The second international FRC workshop, held in Montreal (Canada) in 2014, was the first ACI-fib joint technical event. Many of the objectives identified in 2004 had been achieved by various groups of researchers who shared a common interest in extending the application of FRC materials into the realm of structural engineering and design. The aim of the workshop was to provide the State-of-the-Art on the recent progress that had been made in term of specifications and actual applications for buildings, underground structures, and bridge projects worldwide. The rapid development of codes, the introduction of new materials and the growing interest of the construction industry suggested presenting this forum at closer intervals. In this context, the third international FRC workshop was held in Desenzano (Italy), four years after Montreal. In this first ACI-fib-RILEM joint technical event, the maturity gained through the recent technological developments and large-scale applications were used to show the acceptability of the concrete design using various fibre compositions. The growing interests of civil infrastructure owners in ultra-high-performance fibre-reinforced concrete (UHPFRC) and synthetic fibres in structural applications bring new challenges in terms of concrete technology and design recommendations. In such a short period of time, we have witnessed the proliferation of the use of fibres as structural reinforcement in various applications such as industrial floors, elevated slabs, precast tunnel lining sections, foundations, as well as bridge decks. We are now moving towards addressing many durability-based design requirements by the use of fibres, as well as the general serviceability-based design. However, the possibility of having a residual tensile strength after cracking of the concrete matrix requires a new conceptual approach for a proper design of FRC structural elements. With such a perspective in mind, the aim of FRC2018 workshop was to provide the State-of-the-Art on the recent progress in terms of specifications development, actual applications, and to expose users and researchers to the challenges in the design and construction of a wide variety of structural applications. Considering that at the time of the first workshop, in 2004, no structural codes were available on FRC, we have to recognize the enormous work done by researchers all over the world, who have presented at many FRC events, and convinced code bodies to include FRC among the reliable alternatives for structural applications. This will allow engineers to increasingly utilize FRC with confidence for designing safe and durable structures. Many presentations also clearly showed that FRC is a promising material for efficient rehabilitation of existing infrastructure in a broad spectrum of repair applications. These cases range from sustained gravity loads to harsh environmental conditions and seismic applications, which are some of the broadest ranges of applications in Civil Engineering. The workshop was attended by researchers, designers, owner and government representatives as well as participants from the construction and fibre industries. The presence of people with different expertise provided a unique opportunity to share knowledge and promote collaborative efforts. These interactions are essential for the common goal of making better and sustainable constructions in the near future. The workshop was attended by about 150 participants coming from 30 countries. Researchers from all the continents participated in the workshop, including 24 Ph.D. students, who brought their enthusiasm in FRC structural applications. For this reason, the workshop Co-chairs sincerely thank all the enterprises that sponsored this event. They also extend their appreciation for the support provided by the industry over the last 30 years which allowed research centers to study FRC materials and their properties, and develop applications to making its use more routine and accepted throughout the world. Their important contribution has been essential for moving the knowledge base forward. Finally, we appreciate the enormous support received from all three sponsoring organizations of ACI, fib and Rilem and look forward to paving the path for future collaborations in various areas of common interest so that the developmental work and implementation of new specifications and design procedures can be expedited internationally.

Download or read book Guide for Strengthening of Concrete Structures written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2022-05-01 with total page 338 pages. Available in PDF, EPUB and Kindle. Book excerpt: The idea of preparing a technical document for the repairs and interventions upon concrete structures goes back to the former fib COM 5: Structural Service Life Aspects, being the goal of the then TG 5.9. After a long period of reduced activity, and taking into account the reorganization of fib commissions that meanwhile took place, on June 2017 a different approach was proposed to push forward the task of TG 8.1 (formerly TG 5.9). The (new) goal of TG 8.1 was to deliver a ‘how-to-do’ guide, gathering together protection, repair, and strengthening techniques for concrete structures. Chapters are intended to provide both guidelines and case-studies, serving as support to the application of fib MC 2020 pre-normative specifications. Each chapter was written by an editorial team comprising desirably at least a researcher, a designer and a contractor. Templates have been prepared in order to harmonize the contents and the presentation of the different methods. Following the writing process, chapters were reviewed by experts and, after amendments by the authors, they underwent a second review process by COM 8 and TG 3.4 members, as well as by different practitioners. For each protection, repair and strengthening method addressed in this guide, readers have a description of when to adopt it, which materials and systems are required, which techniques are available, and what kind of equipment is needed. It then presents a summary of stakeholders’ roles and qualifications, design guidelines referring to most relevant codes and references, the intervention procedure, quality control measures and monitoring and maintenance activities. Due to the extent of the guide, it was decided to publish it as bulletin 102, addressing protection and repair methods, and bulletin 103, addressing strengthening methods. We would like to thank the authors, reviewers and members of COM 8 and TG 3.4 for their work in developing this fib Bulletin, which we hope will be useful for professionals working in the field of existing concrete structures, especially those concerned with life-cycle management and conservation activities. As noted above, this Bulletin is also intended to act as a background and supporting document to the next edition of the fib Model Code for Concrete Structures, which is currently under development under the auspices of TG10.1 with the working title of ‘fib Model Code 2020’.

Download or read book Guide for Protection and Repair of Concrete Structures written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2022-03-01 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: The idea of preparing a technical document for the repairs and interventions upon concrete structures goes back to the former fib COM5: Structural Service Life Aspects, being the goal of the then TG5.9. After a long period of reduced activity, and taking into account the reorganization of fib commissions that meanwhile took place, on June 2017 a different approach was proposed to push forward the task of TG8.1 (formerly TG5.9). The (new) goal of TG 8.1 was to deliver a ‘how-to-do’ guide, gathering together protection, repair, and strengthening techniques for concrete structures. Chapters are intended to provide both guidelines and case-studies, serving as support to the application of fib MC2020 pre-normative specifications. Each chapter was written by an editorial team comprising desirably at least a researcher, a designer and a contractor. Templates have been prepared in order to harmonize the contents and the presentation of the different methods. Following the writing process, chapters were reviewed by experts and, after amendments by the authors, they underwent a second review process by COM8 and TG3.4 members, as well as by different practitioners. For each protection, repair and strengthening method addressed in this guide, readers have a description of when to adopt it, which materials and systems are required, which techniques are available, and what kind of equipment is needed. It then presents a summary of stakeholders’ roles and qualifications, design guidelines referring to most relevant codes and references, the intervention procedure, quality control measures and monitoring and maintenance activities. Due to the extent of the guide, it was decided to publish it as bulletin 102, addressing protection and repair methods, and bulletin 103, addressing strengthening methods. We would like to thank the authors, reviewers and members of COM8 and TG3.4 for their work in developing this fib Bulletin, which we hope will be useful for professionals working in the field of existing concrete structures, especially those concerned with life-cycle management and conservation activities. As noted above, this Bulletin is also intended to act as a background and supporting document to the next edition of the fib Model Code for Concrete Structures, which is currently under development under the auspices of TG10.1 with the working title of "fib Model Code 2020".

Download or read book Advances on bond in concrete written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2022-12-01 with total page 326 pages. Available in PDF, EPUB and Kindle. Book excerpt: Structural behavior of reinforced concrete elements strongly depends on the interaction between the reinforcing bars and the surrounding concrete, which is generally referred as “bond in concrete”. In service conditions, the reinforcement-to-concrete bond governs deformability through the tension stiffening of concrete surrounding the bar as well the crack development and crack width. At Ultimate Limit State, bond governs anchorage and lap splices behavior as well as structural ductility. When plain (smooth) bars were used, the steel-to-concrete bond was mainly associated with “chemical adhesion/friction” that is related to the surface roughness of the rebar. As steel strengths increased the need to enhance interaction between steel and the surrounding concrete was recognized, and square twisted rebars, indented rebars or, later on, ribbed rebars came into the market, the latter being the type of deformed bar most commonly adopted since the 1960/70s. When ribbed rebars became widely used, several research studies started worldwide for better understanding the interaction between ribs and the surrounding concrete. Researchers evidenced the development of micro-cracks (due to the wedge action of the ribs) towards the external face of the structural element. If confinement is provided by the concrete cover, by transverse reinforcement or by an external transverse pressure, the full-anchorage capacity is guaranteed and a pull-out failure occurs, with crushing of concrete between the ribs. On the contrary, with lesser confining action, a splitting failure of bond occurs; the latter may provoke a brittle failure of the lap splice or, in some cases, of anchorages. However, after many years of research studies on bond-related topics, there are still several open issues. In fact, new materials entered into the market, as concrete with recycled aggregates or fibre reinforced concrete; the latter, having a kind of distributed reinforcement into the matrix (the fibres), provides a better confinement to the wedge action of the ribs. In addition, concrete and steel strength continuously increased over the years, causing changes in the bond behavior due to differences in mechanical properties of materials but also to the different concrete composition at the interface with the steel rebar causing a different bond behavior. Moreover, the lower water/cement ratio of these high-strength concrete makes the bleeding phenomena less evident, changing the concrete porosity in the upper layers of the structural element and thus making the current casting position parameters no-longer reliable. Finally, concrete with recycled aggregates are becoming more important in a market that is looking forward to a circular economy. As such, all the experimental results and database that allowed the calibration of bond rules now present in building codes for conventional concrete, may be not be representative of these new types of materials nowadays adopted in practice. Furthermore, after more than 50 years of service life, structural elements may not satisfy the current safety requirements for several reasons, including material degradation (with particular reference to steel corrosion) or increased loads, by also considering the seismic actions that were non considered by building codes at the time of the original design. The structural assessment of existing structures requires proper conceptual models and new approaches for evaluating the reliability of existing structures by also considering the remaining expected service life. In addition, specific rules for older materials, as plain smooth bars, should be revised for a better assessment of old structures. Last, but not least, interventions in existing structures may require new technologies now available such as post-installed rebars. While many advances have been achieved, there remain areas where a better understanding of bond and its mechanisms are required, and where further work is required to incorporate this understanding into safe and economic rules to guide construction and maintenance of existing infrastructures. These aspects were widely discussed within the technical community, particularly in the fib Task Group 2.5 and in the ACI 408 Committee dealing with bond and anchorage issues. Furthermore, special opportunities for discussing bond developments were represented by the International Conferences on ‘Bond in Concrete’ held each decade since 1982 as well as by joint workshops organized by fib TG2.5 and ACI 408. Within this technical collaboration, this Bulletin was conceived, and, thus, it collects selected papers presented at the joint fib-ACI Convention Session on Bond in Concrete held in Detroit (USA) in 2017. The bulletin is based on four main Sections concerning: - General aspects of bond - Anchorages and laps of bars and prestressing tendons - Bond under severe conditions - Degradation of bond for corrosion - Bond in new types of concrete The main aim of the Bulletin is to shed some new lights on the advances in understanding and application of bond related issues achieved over the last few years, and identify the challenges and priorities to be addressed in the next years. Another important aspect of the bulletin is to provide practical information from research findings.

Download or read book Serviceability Limit State of Concrete Structures written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2019-09-01 with total page 219 pages. Available in PDF, EPUB and Kindle. Book excerpt: Serviceability limit states are essential for appropriate function and durability of concrete structures. The attention is paid especially to the stress limitation, crack width analysis and deflection analysis. The document provides supplementary information to the fib Model Code 2010 (MC2010), where a limited space did not allow for a detailed description of individual procedures. The principles used in MC2010 in chapter 7.6 are explained in detail within this document. The stress analysis is focused on stresses in concrete and steel including the stress redistribution due to the long-term load and cracking of reinforced concrete and prestressed concrete elements. Crack width analysis explains the mechanism of cracking under mechanical loading and due to deformation restraint. Cracks in prestressed concrete elements are also discussed. Deflection analyses with different levels of accuracy are described including the shear effects. Examples illustrate the practical application of rules defined in the MC2010 of individual serviceability limit states. Simplified and more general methods are used. An important part of the bulletin shows the development and extension of the serviceability limit states after publishing of the MC2010 and alternative approaches. Special attention is paid to deflections of prestressed concrete beams, shear effects on deflection, slenderness limits and influence of the concrete cover. The final part deals with an application of numerical simulations.

Download or read book Conceptual Design of Precast Concrete Bridge Superstructures written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2021-08-01 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete bridges are an important part of today's road infrastructure. An important part of those concrete bridges is to a large extent prefabricated. Precast concrete enables all the advantages of an industrialized process to be fully utilized. Contemporary concrete mixtures are used to realize high-strength bridge girders and piers that exactly meet the requirements set, both structurally and aesthetically, with a small ecological footprint. Sustainable and durable! On the construction site, there is no need for complex formwork, the execution time is drastically reduced and where road, water and rail traffic on or under the bridge has to be temporarily interrupted, it is only minimally inconvenienced during the execution of the project. Bridges capture the imagination. In addition to their pure functionality, overcoming a height difference, they offer designers unprecedented opportunities to shape their creativity, including when using precast concrete. This bulletin, prepared by the experts of Task Group 6.5 'Precast concrete bridges', takes a closer look at the conceptual (preliminary) design of prefabricated concrete bridges. The bulletin does not have the ambition to define the umbrella term 'conceptual design' but shows in a pragmatic way, using 24 examples spread all over the world, how leading designers use this methodology to select from the many possibilities to arrive at an ideal solution taking into account all design conditions. One often reads that experience is a necessary condition for good conceptual design. The pooled knowledge and experience in this bulletin already provide the reader with a good head start. Commission 6 thanks the former convener of the Task Group Hugo Corres, editor of this document, and the current co-conveners Marcello Waimberg and Ken-ichi Kata as well as all active members of the Task Group for sharing their knowledge and experience and for the successful realization of this bulletin.

Download or read book Acceptance of post tensioning systems for cryogenic applications written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 2021-04-01 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the Second World War the demand of energy has undergone an exponential growth that has led to a sharp annual increase in the use of natural gas in both, cities and thermal power stations. Nowadays, the strategic relevance of natural gas as a main source of energy is evident with a contribution of more than 20% of the total world consumption. This development in increasing demand of natural gas has led for a need of suitable storage and transportation infrastructure. Various gases, especially hydrocarbons, are preferably stored in liquid form for transportation and storage since the phase transformation from gas to liquid comes with a significant reduction of the volume (e.g. up to 600 times). Gases can be liquefied by raising the pressure or by cooling to their boiling point, which for most gases is below 0°C. This is known as cryogenic storage. The term cryogenic is derived from two Greek words, namely kryos meaning icy-cold and genes which can be translated as shape. These fib recommendations are concerned about post-tensioning systems used in cryogenic tanks and have been formulated on the basis of actual available knowledge with the aim to reflect the current state of the art. Consequently, these recommendations have included a classification of the different cryogenic tanks typologies used in the past and nowadays, the associated different tendon types depending on their exposure to low temperature (e.g. never, only accidentally or during normal tank operation) and the testing regime required for acceptance of the materials and the post-tensioning system according to this document. An international working group comprising more than 20 experts from administrative authorities, universities, laboratories, owners, structural designers, suppliers of prestressing steels and post-tensioning systems suppliers have actively contributed in order to develop these recommendations. This text has been written to cover best construction practices around the world, and to provide material specifications which are considered to be the most advanced available at the time of preparing this text. For ease of use (for Owner, Designer and Post-tensioning System Supplier), the content has been arranged systematically according to the system components into chapters focusing on performance characteristics, requirements and acceptance criteria.