Download or read book An Introduction to SOLIDWORKS Flow Simulation 2021 written by John Matsson and published by SDC Publications. This book was released on 2021-04 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Introduction to SOLIDWORKS Flow Simulation 2021 takes you through the steps of creating the SOLIDWORKS part for the simulation followed by the setup and calculation of the SOLIDWORKS Flow Simulation project. The results from calculations are visualized and compared with theoretical solutions and empirical data. Each chapter starts with the objectives and a description of the specific problems that are studied. End of chapter exercises are included for reinforcement and practice of what has been learned. The fourteen chapters of this book are directed towards first-time to intermediate level users of SOLIDWORKS Flow Simulation. It is intended to be a supplement to undergraduate Fluid Mechanics and Heat Transfer related courses. This book can also be used to show students the capabilities of fluid flow and heat transfer simulations in freshman and sophomore courses such as Introduction to Engineering. Both internal and external flow problems are covered and compared with experimental results and analytical solutions. Covered topics include airfoil flow, boundary layers, flow meters, heat exchanger, natural and forced convection, pipe flow, rotating flow, tube bank flow and valve flow. Covers these feature of SOLIDWORKS Flow Simulation 2021: Animations Automatic and Manual Meshing Boundary Conditions Calculation Control Options External and Internal Flow Goals Laminar and Turbulent Flow Physical Features Result Visualizations Two and Three Dimensional Flow Velocity, Thermodynamic and Turbulence Parameters Wall Thermal Conditions Free Surfaces

Download or read book An Introduction to SolidWorks Flow Simulation 2012 written by John E. Matsson and published by SDC Publications. This book was released on 2012 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Introduction to SolidWorks Flow Simulation 2012 takes you through the steps of creating the SolidWorks part for the simulation followed by the setup and calculation of the SolidWorks Flow Simulation project. The results from calculations are visualized and compared with theoretical solutions and empirical data. Each chapter starts with the objectives and a description of the specific problems that are studied. End of chapter exercises are included for reinforcement and practice of what has been learned. The thirteen chapters of this book are directed towards first-time to intermediate level users of SolidWorks Flow Simulation. It is intended to be a supplement to undergraduate Fluid Mechanics and Heat Transfer related courses. This book can also be used to show students the capabilities of fluid flow and heat transfer simulations in freshman and sophomore courses such as Introduction to Engineering. Both internal and external flow problems are covered and compared with experimental results and analytical solutions. Covered topics include airfoil flow, boundary layers, flow meters, heat exchanger, natural and forced convection, pipe flow, rotating flow, tube bank flow and valve flow.

Download or read book Autodesk CFD 2021 Black Book Colored written by Gaurav Verma and published by Cadcamcae Works. This book was released on 2021-05-25 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Autodesk CFD 2021 Black Book, is the 2nd edition of our series on Autodesk CFD. The book is targeted for beginners of Autodesk CFD. This book covers the basic equations and terms of Fluid Dynamics theory. The book covers all the major tools of Flow Simulation modules like Fluid Flow, Thermal Fluid Flow, and Electronic Cooling modules. This book can be used as supplement to Fluid Dynamics course if your subject requires the application of Software for solving CFD problems. Some of the salient features of this book are: In-Depth explanation of concepts Every new topic of this book starts with the explanation of the basic concepts. In this way, the user becomes capable of relating the things with real world. Topics Covered Every chapter starts with a list of topics being covered in that chapter. In this way, the user can easy find the topic of his/her interest easily. Instruction through illustration The instructions to perform any action are provided by maximum number of illustrations so that the user can perform the actions discussed in the book easily and effectively. There are about 500 illustrations that make the learning process effective. Tutorial point of view The book explains the concepts through the tutorial to make the understanding of users firm and long lasting. Practical of the book are based on real world projects. For Faculty If you are a faculty member, then you can ask for video tutorials on any of the topic, exercise, tutorial, or concept.

Download or read book Engineering Analysis with SolidWorks Simulation 2012 written by Paul M. Kurowski and published by SDC Publications. This book was released on 2012 with total page 467 pages. Available in PDF, EPUB and Kindle. Book excerpt: Engineering Analysis with SolidWorks Simulation 2012 goes beyond the standard software manual. Its unique approach concurrently introduces you to the SolidWorks Simulation 2012 software and the fundamentals of Finite Element Analysis (FEA) through hands-on exercises. A number of projects are presented using commonly used parts to illustrate the analysis features of SolidWorks Simulation. Each chapter is designed to build on the skills, experiences and understanding gained from the previous chapters. Topics covered: Linear static analysis of parts and assemblies Contact stress analysis Frequency (modal) analysis Buckling analysis Thermal analysis Drop test analysis Nonlinear analysis Dynamic analysis Random vibration analysis h and p adaptive solution methods Modeling techniques Implementation of FEA in the design process Management of FEA projects FEA terminology

Download or read book An Introduction to SOLIDWORKS Flow Simulation 2016 written by John Matsson and published by SDC Publications. This book was released on 2016-07 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Introduction to SOLIDWORKS Flow Simulation 2016 takes you through the steps of creating the SOLIDWORKS part for the simulation followed by the setup and calculation of the SOLIDWORKS Flow Simulation project. The results from calculations are visualized and compared with theoretical solutions and empirical data. Each chapter starts with the objectives and a description of the specific problems that are studied. End of chapter exercises are included for reinforcement and practice of what has been learned. The fourteen chapters of this book are directed towards first-time to intermediate level users of SOLIDWORKS Flow Simulation. It is intended to be a supplement to undergraduate Fluid Mechanics and Heat Transfer related courses. This book can also be used to show students the capabilities of fluid flow and heat transfer simulations in freshman and sophomore courses such as Introduction to Engineering. Both internal and external flow problems are covered and compared with experimental results and analytical solutions. Covered topics include airfoil flow, boundary layers, flow meters, heat exchanger, natural and forced convection, pipe flow, rotating flow, tube bank flow and valve flow.

Download or read book FreeCAD 0 20 Black Book written by Gaurav Verma and published by CADCAMCAE Works. This book was released on 2022-10-10 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: The FreeCAD 0.20 Black Book is the 3rd edition of our series on FreeCAD. This book is written to help beginners in creating some of the most complex solid models. The book follows a step by step methodology. In this book, we have tried to give real-world examples with real challenges in designing. We have tried to cover most of the topics utilized in industries for designing. The book covers almost all the information required by a learner to master the FreeCAD. The book starts with sketching and ends at advanced topics like Path (CAM), and FEM (Simulation). In this edition, we have added tools of addon workbenches like Sheet Metal, CFDOf, Assembly4, and so on. Some of the salient features of this book are : In-Depth explanation of concepts Every new topic of this book starts with the explanation of the basic concepts. In this way, the user becomes capable of relating the things with real world. Topics Covered Every chapter starts with a list of topics being covered in that chapter. In this way, the user can easily find the topics of his/her interest easily. Instruction through illustration The instructions to perform any action are provided by maximum number of illustrations so that the user can perform the actions discussed in the book easily and effectively. There are about 2012 illustrations that make the learning process effective. Tutorial point of view At the end of concept’s explanation, the tutorial make the understanding of users firm and long lasting. Almost each chapter of the book has tutorials that are real world projects. Moreover most of the tools in this book are discussed in the form of tutorials. Project Projects and exercises are provided to students for practicing. For Faculty If you are a faculty member, then you can ask for video tutorials on any of the topic, exercise, tutorial, or concept. As faculty, you can register on our website to get electronic desk copies of our latest books. Faculty resources are available in the Faculty Member page of our website once you login. Note that faculty registration approval is manual and it may take two days for approval before you can access the faculty website.

Download or read book Motion Simulation and Mechanism Design with SOLIDWORKS Motion 2021 written by Kuang-Hua Chang and published by SDC Publications. This book was released on 2021-07-15 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt: Motion Simulation and Mechanism Design with SOLIDWORKS Motion 2021 is written to help you become familiar with SOLIDWORKS Motion, an add-on module of the SOLIDWORKS software family. This book covers the basic concepts and frequently used commands required to advance readers from a novice to intermediate level in using SOLIDWORKS Motion. SOLIDWORKS Motion allows you to use solid models created in SOLIDWORKS to simulate and visualize mechanism motion and performance. Using SOLIDWORKS Motion early in the product development stage could prevent costly redesign due to design defects found in the physical testing phase. Therefore, using SOLIDWORKS Motion contributes to a more cost effective, reliable, and efficient product design process. Basic concepts discussed in this book include model generation, such as creating assembly mates for proper motion; carrying out simulation and animation; and visualizing simulation results, such as graphs and spreadsheet data. These concepts are introduced using simple, yet realistic examples. Verifying the results obtained from the computer simulation is extremely important. One of the unique features of this book is the incorporation of theoretical discussions for kinematic and dynamic analyses in conjunction with the simulation results obtained using SOLIDWORKS Motion. Verifying the simulation results will increase your confidence in using the software and prevent you from being fooled by erroneous simulations. This book covers the following functionality of SOLIDWORKS Motion 2021 Model generation Creating assembly mates Performing simulations Creating animations Visualizing simulation results

Download or read book Introduction to Finite Element Analysis Using SolidWorks Simulation 2011 written by Randy Shih and published by SDC Publications. This book was released on 2011-01-20 with total page 457 pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary goal of Introduction to Finite Element Analysis Using SolidWorks Simulation 2011 is to introduce the aspects of Finite Element Analysis (FEA) that are important to engineers and designers. Theoretical aspects of Finite Element Analysis are also introduced as they are needed to help better understand the operation. The primary emphasis of the text is placed on the practical concepts and procedures needed to use SolidWorks Simulation in performing Linear Static Stress Analysis and basic Model Analysis. This text covers SolidWorks Simulation and the lessons proceed in a pedagogical fashion to guide you from constructing basic truss elements to generating three-dimensional solid elements from solid models. This text takes a hands-on, exercise-intensive approach to all the important Finite Element Analysis techniques and concepts. This textbook contains a series of thirteen tutorial style lessons designed to introduce beginning FEA users to SolidWorks Simulation. The basic premise of this book is that the more designs you create using SolidWorks Simulation, the better you learn the software. With this in mind, each lesson introduces a new set of commands and concepts, building on previous lessons.

Download or read book An Introduction to SOLIDWORKS Flow Simulation 2018 written by John Matsson and published by SDC Publications. This book was released on 2018 with total page 330 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Introduction to SOLIDWORKS Flow Simulation 2018 takes you through the steps of creating the SOLIDWORKS part for the simulation followed by the setup and calculation of the SOLIDWORKS Flow Simulation project. The results from calculations are visualized and compared with theoretical solutions and empirical data. Each chapter starts with the objectives and a description of the specific problems that are studied. End of chapter exercises are included for reinforcement and practice of what has been learned. The fourteen chapters of this book are directed towards first-time to intermediate level users of SOLIDWORKS Flow Simulation. It is intended to be a supplement to undergraduate Fluid Mechanics and Heat Transfer related courses. This book can also be used to show students the capabilities of fluid flow and heat transfer simulations in freshman and sophomore courses such as Introduction to Engineering. Both internal and external flow problems are covered and compared with experimental results and analytical solutions. Covered topics include airfoil flow, boundary layers, flow meters, heat exchanger, natural and forced convection, pipe flow, rotating flow, tube bank flow and valve flow.

Download or read book An Introduction to SOLIDWORKS Flow Simulation 2019 written by John Matsson and published by SDC Publications. This book was released on 2019 with total page 331 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Introduction to SOLIDWORKS Flow Simulation 2019 takes you through the steps of creating the SOLIDWORKS part for the simulation followed by the setup and calculation of the SOLIDWORKS Flow Simulation project. The results from calculations are visualized and compared with theoretical solutions and empirical data. Each chapter starts with the objectives and a description of the specific problems that are studied. End of chapter exercises are included for reinforcement and practice of what has been learned. The fourteen chapters of this book are directed towards first-time to intermediate level users of SOLIDWORKS Flow Simulation. It is intended to be a supplement to undergraduate Fluid Mechanics and Heat Transfer related courses. This book can also be used to show students the capabilities of fluid flow and heat transfer simulations in freshman and sophomore courses such as Introduction to Engineering. Both internal and external flow problems are covered and compared with experimental results and analytical solutions. Covered topics include airfoil flow, boundary layers, flow meters, heat exchanger, natural and forced convection, pipe flow, rotating flow, tube bank flow and valve flow.

Download or read book Introduction to SolidWorks written by Godfrey C. Onwubolu and published by CRC Press. This book was released on 2017-03-03 with total page 1676 pages. Available in PDF, EPUB and Kindle. Book excerpt: This senior undergraduate level textbook is written for Advanced Manufacturing, Additive Manufacturing, as well as CAD/CAM courses. Its goal is to assist students in colleges and universities, designers, engineers, and professionals interested in using SolidWorks as the design and 3D printing tool for emerging manufacturing technology for practical applications. This textbook will bring a new dimension to SolidWorks by introducing readers to the role of SolidWorks in the relatively new manufacturing paradigm shift, known as 3D-Printing which is based on Additive Manufacturing (AM) technology. This new textbook: Features modeling of complex parts and surfaces Provides a step-by-step tutorial type approach with pictures showing how to model using SolidWorks Offers a user-Friendly approach for the design of parts, assemblies, and drawings, motion-analysis, and FEA topics Includes clarification of connections between SolidWorks and 3D-Printing based on Additive Manufacturing Discusses a clear presentation of Additive Manufacturing for Designers using SolidWorks CAD software "Introduction to SolidWorks: A Comprehensive Guide with Applications in 3D Printing" is written using a hands-on approach which includes a significant number of pictorial descriptions of the steps that a student should follow to model parts, assemble parts, and produce drawings.

Download or read book Analysis of Machine Elements Using SOLIDWORKS Simulation 2021 written by Shahin S. Nudehi and published by SDC Publications. This book was released on 2021-07-03 with total page 556 pages. Available in PDF, EPUB and Kindle. Book excerpt: • Designed for first-time SOLIDWORKS Simulation users • Focuses on examples commonly found in Design of Machine Elements courses • Many problems are accompanied by solutions using classical equations • Combines step-by-step tutorials with detailed explanations of why each step is taken Analysis of Machine Elements Using SOLIDWORKS Simulation 2021 is written primarily for first-time SOLIDWORKS Simulation 2021 users who wish to understand finite element analysis capabilities applicable to stress analysis of mechanical elements. The focus of examples is on problems commonly found in introductory, undergraduate, Design of Machine Elements or similarly named courses. In order to be compatible with most machine design textbooks, this text begins with problems that can be solved with a basic understanding of mechanics of materials. Problem types quickly migrate to include states of stress found in more specialized situations common to a design of mechanical elements course. Paralleling this progression of problem types, each chapter introduces new software concepts and capabilities. Many examples are accompanied by problem solutions based on use of classical equations for stress determination. Unlike many step-by-step user guides that only list a succession of steps, which if followed correctly lead to successful solution of a problem, this text attempts to provide insight into why each step is performed. This approach amplifies two fundamental tenets of this text. The first is that a better understanding of course topics related to stress determination is realized when classical methods and finite element solutions are considered together. The second tenet is that finite element solutions should always be verified by checking, whether by classical stress equations or experimentation. Each chapter begins with a list of learning objectives related to specific capabilities of the SOLIDWORKS Simulation program introduced in that chapter. Most software capabilities are repeated in subsequent examples so that users gain familiarity with their purpose and are capable of using them in future problems. All end-of-chapter problems are accompanied by evaluation "check sheets" to facilitate grading assignments. Table of Contents Introduction 1. Stress Analysis Using SOLIDWORKS Simulation 2. Curved Beam Analysis 3. Stress Concentration Analysis 4. Thin and Thick Wall Pressure Vessels 5. Interference Fit Analysis 6. Contact Analysis 7. Bolted Joint Analysis 8. Design Optimization 9. Elastic Buckling 10. Fatigue Testing Analysis 11. Thermal Stress Analysis Appendix A: Organizing Assignments Using MS Word Appendix B: Alternate Method to Change Screen Background Color Index

Download or read book Thermal Analysis with SOLIDWORKS Simulation 2022 and Flow Simulation 2022 written by Paul Kurowski and published by SDC Publications. This book was released on with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal Analysis with SOLIDWORKS Simulation 2022 goes beyond the standard software manual. It concurrently introduces the reader to thermal analysis and its implementation in SOLIDWORKS Simulation using hands-on exercises. A number of projects are presented to illustrate thermal analysis and related topics. Each chapter is designed to build on the skills and understanding gained from previous exercises. Thermal Analysis with SOLIDWORKS Simulation 2022 is designed for users who are already familiar with the basics of Finite Element Analysis (FEA) using SOLIDWORKS Simulation or who have completed the book Engineering Analysis with SOLIDWORKS Simulation 2022. Thermal Analysis with SOLIDWORKS Simulation 2022 builds on these topics in the area of thermal analysis. Some understanding of FEA and SOLIDWORKS Simulation is assumed. Topics covered Analogies between thermal and structural analysis Heat transfer by conduction Heat transfer by convection Heat transfer by radiation Thermal loads and boundary conditions Thermal resistance Thermal stresses Thermal buckling Modeling techniques in thermal analysis Presenting results of thermal analysis

Download or read book Analysis of Machine Elements Using SOLIDWORKS Simulation 2022 written by Shahin S. Nudehi and published by SDC Publications. This book was released on with total page 556 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analysis of Machine Elements Using SOLIDWORKS Simulation 2022 is written primarily for first-time SOLIDWORKS Simulation 2022 users who wish to understand finite element analysis capabilities applicable to stress analysis of mechanical elements. The focus of examples is on problems commonly found in introductory, undergraduate, Design of Machine Elements or similarly named courses. In order to be compatible with most machine design textbooks, this text begins with problems that can be solved with a basic understanding of mechanics of materials. Problem types quickly migrate to include states of stress found in more specialized situations common to a design of mechanical elements course. Paralleling this progression of problem types, each chapter introduces new software concepts and capabilities. Many examples are accompanied by problem solutions based on use of classical equations for stress determination. Unlike many step-by-step user guides that only list a succession of steps, which if followed correctly lead to successful solution of a problem, this text attempts to provide insight into why each step is performed. This approach amplifies two fundamental tenets of this text. The first is that a better understanding of course topics related to stress determination is realized when classical methods and finite element solutions are considered together. The second tenet is that finite element solutions should always be verified by checking, whether by classical stress equations or experimentation. Each chapter begins with a list of learning objectives related to specific capabilities of the SOLIDWORKS Simulation program introduced in that chapter. Most software capabilities are repeated in subsequent examples so that users gain familiarity with their purpose and are capable of using them in future problems. All end-of-chapter problems are accompanied by evaluation "check sheets" to facilitate grading assignments.

Download or read book Introduction to Finite Element Analysis Using SOLIDWORKS Simulation 2020 written by Randy Shih and published by SDC Publications. This book was released on 2020 with total page 511 pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary goal of Introduction to Finite Element Analysis Using SOLIDWORKS Simulation 2020 is to introduce the aspects of Finite Element Analysis (FEA) that are important to engineers and designers. Theoretical aspects of FEA are also introduced as they are needed to help better understand the operation. The primary emphasis of the text is placed on the practical concepts and procedures needed to use SOLIDWORKS Simulation in performing Linear Static Stress Analysis and basic Modal Analysis. This text covers SOLIDWORKS Simulation and the lessons proceed in a pedagogical fashion to guide you from constructing basic truss elements to generating three-dimensional solid elements from solid models. This text takes a hands-on, exercise-intensive approach to all the important FEA techniques and concepts. This textbook contains a series of fourteen tutorial style lessons designed to introduce beginning FEA users to SOLIDWORKS Simulation. The basic premise of this book is that the more designs you create using SOLIDWORKS Simulation, the better you learn the software. With this in mind, each lesson introduces a new set of commands and concepts, building on previous lessons.

Download or read book Finite Element Analysis Concepts written by J. E. Akin and published by World Scientific. This book was released on 2010 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt: Young engineers are often required to utilize commercial finite element software without having had a course on finite element theory. That can lead to computer-aided design errors. This book outlines the basic theory, with a minimum of mathematics, and how its phases are structured within a typical software. The importance of estimating a solution, or verifying the results, by other means is emphasized and illustrated. The book also demonstrates the common processes for utilizing the typical graphical icon interfaces in commercial codes. in particular, the book uses and covers the widely utilized SolidWorks solid modeling and simulation system to demonstrate applications in heat transfer, stress analysis, vibrations, buckling, and other fields. The book, with its detailed applications, will appeal to upper-level undergraduates as well as engineers new to industry.

Download or read book Motion Simulation and Mechanism Design with SOLIDWORKS Motion 2020 written by Kuang-Hua Chang and published by SDC Publications. This book was released on with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt: Motion Simulation and Mechanism Design with SOLIDWORKS Motion 2020 is written to help you become familiar with SOLIDWORKS Motion, an add-on module of the SOLIDWORKS software family. This book covers the basic concepts and frequently used commands required to advance readers from a novice to intermediate level in using SOLIDWORKS Motion. SOLIDWORKS Motion allows you to use solid models created in SOLIDWORKS to simulate and visualize mechanism motion and performance. Using SOLIDWORKS Motion early in the product development stage could prevent costly redesign due to design defects found in the physical testing phase. Therefore, using SOLIDWORKS Motion contributes to a more cost effective, reliable, and efficient product design process. Basic concepts discussed in this book include model generation, such as creating assembly mates for proper motion; carrying out simulation and animation; and visualizing simulation results, such as graphs and spreadsheet data. These concepts are introduced using simple, yet realistic examples. Verifying the results obtained from the computer simulation is extremely important. One of the unique features of this book is the incorporation of theoretical discussions for kinematic and dynamic analyses in conjunction with the simulation results obtained using SOLIDWORKS Motion. Verifying the simulation results will increase your confidence in using the software and prevent you from being fooled by erroneous simulations. This book covers the following functionality of SOLIDWORKS Motion 2020 • Model generation • Creating assembly mates • Performing simulations • Creating animations • Visualizing simulation results