Download or read book Densification of Metal Powders During Sintering written by V. A. Invenson and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 241 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sintering of powder metal compacts is one of the basic oper ations in powder metallurgy. The useful properties of a machine part are obtained after considerable densification of the sintered material. Although the mechanical properties of the part depend on other structural factors besides porosity, porosity is the main factor. Usually, the practical problem in sintering is to obtain a part with the desired or permissible porosity. Thus, knowledge of the laws governing densification and its final result is neces sary to control this process in the production of powder metal parts. The laws governing densification are also important for a more exact physical theory of sintering, which is still in the initial stages of its development. Such processes as the change in the density of lattice defects and the flow of crystalline substances during sintering have not yet received a complete physical inter pretation. Analysis of the laws of sintering may provide addition al material for more complete phenomenological characteristics of these processes that will be useful for further development of theoretical concepts of the flow of imperfect crystals under small loads. Although a substantial amount of experimental material has been accumulated, generalizations are still difficult.

Download or read book Densification of Metal Powders During Sintering written by V. A. Invenson and published by Springer. This book was released on 2012-05-02 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sintering of powder metal compacts is one of the basic oper ations in powder metallurgy. The useful properties of a machine part are obtained after considerable densification of the sintered material. Although the mechanical properties of the part depend on other structural factors besides porosity, porosity is the main factor. Usually, the practical problem in sintering is to obtain a part with the desired or permissible porosity. Thus, knowledge of the laws governing densification and its final result is neces sary to control this process in the production of powder metal parts. The laws governing densification are also important for a more exact physical theory of sintering, which is still in the initial stages of its development. Such processes as the change in the density of lattice defects and the flow of crystalline substances during sintering have not yet received a complete physical inter pretation. Analysis of the laws of sintering may provide addition al material for more complete phenomenological characteristics of these processes that will be useful for further development of theoretical concepts of the flow of imperfect crystals under small loads. Although a substantial amount of experimental material has been accumulated, generalizations are still difficult.

Download or read book Sintering of powder materials written by Дина Дудина and published by Litres. This book was released on 2022-12-07 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study guide corresponds to «Sintering of powder materials» course of the Master degree program at Novosibirsk State Technical University 22.04.01 – Materials Science and Technology. The guide consists of six parts and contains a brief overview of historical aspects of sintering, powder fabrication and characterization methods, powder shaping and compaction processes, and the basics of solid state and liquid phase sintering. The guide also contains a description of advanced sintering methods and sintering processes found in additive manufacturing. Classical and novel materials obtainable by sintering are described. Current trends in the development of sintering science are discussed. Each part of the guide is followed by control questions. Problems with solutions are offered to help the student solve problems encountered in real research and industrial sintering practice. Problems for self-study are also provided, many of which were designed by the author based on her own research experience. Topics for self-study are provided and can be used for students' presentations at seminars.

Download or read book Sintering of Advanced Materials written by Zhigang Zak Fang and published by Elsevier. This book was released on 2010-09-27 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sintering is a method for manufacturing components from ceramic or metal powders by heating the powder until the particles adhere to form the component required. The resulting products are characterised by an enhanced density and strength, and are used in a wide range of industries. Sintering of advanced materials: fundamentals and processes reviews important developments in this technology and its applicationsPart one discusses the fundamentals of sintering with chapters on topics such as the thermodynamics of sintering, kinetics and mechanisms of densification, the kinetics of microstructural change and liquid phase sintering. Part two reviews advanced sintering processes including atmospheric sintering, vacuum sintering, microwave sintering, field/current assisted sintering and photonic sintering. Finally, Part three covers sintering of aluminium, titanium and their alloys, refractory metals, ultrahard materials, thin films, ultrafine and nanosized particles for advanced materials.With its distinguished editor and international team of contributors, Sintering of advanced materials: fundamentals and processes reviews the latest advances in sintering and is a standard reference for researchers and engineers involved in the processing of ceramics, powder metallurgy, net-shape manufacturing and those using advanced materials in such sectors as electronics, automotive and aerospace engineering. Explores the thermodynamics of sintering including sinter bonding and densification Chapters review a variety of sintering methods including atmosphere, vacuum, liquid phase and microwave sintering Discusses sintering of a variety of materials featuring refractory metals, super hard materials and functionally graded materials

Download or read book Sintering written by Suk-Joong L. Kang and published by Elsevier. This book was released on 2004-11-27 with total page 279 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sintering is the process of forming materials and components from a powder under the action of thermal energy. It is a key materials science subject: most ceramic materials and many specialist metal powder products for use in key industries such as electronics, automotive and aerospace are formed this way. Written by one of the leading experts in the field, this book offers an unrivalled introduction to sintering and sintering processes for students of materials science and engineering, and practicing engineers in industry. The book is unique in providing a complete grounding in the principles of sintering and equal coverage of the three key sintering processes: densification, grain growth and microstructure. Students and professional engineers alike will be attracted by the emphasis on developing a detailed understanding of the theory and practical processes of sintering, the balanced coverage of ceramic and metal sintering, and the accompanying examination questions with selected solutions. Delivering unrivalled depth of coverage on the basis of sintering, science, including thermodynamics and polycrystalline microstructure. Unique in its balanced coverage of the three key sintering elements - densification, grain growth and microstructure. A key reference for students and engineers in materials science and engineering, accompanied by examination questions and selected solutions.

Download or read book Powder Metallurgy written by Leszek A. Dobrzański and published by BoD – Books on Demand. This book was released on 2017-03-29 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book presents the fundamentals and the role of powder metallurgy in contemporary technologies and the state of the art of classical powder metallurgy technologies and a general description of new variants and special and hybrid technologies used in powder metallurgy. The next part includes over a dozen case studies provided in the following chapters, comprehensively describing authors' accomplishments of numerous teams from different countries across the world in advanced research areas relating to powder metallurgy and to special and hybrid technologies. The detailed information, largely deriving from own and original research and R

Download or read book Sintering From Empirical Observations to Scientific Principles written by Randall German and published by Butterworth-Heinemann. This book was released on 2014-02-07 with total page 549 pages. Available in PDF, EPUB and Kindle. Book excerpt: As sintering applications march toward a $30 billion global business, the models for sintering have progressed, but generally follow behind observation. Documentation of the steps needed to build to a quantitative and predictive theory are often missed. Sintering: From Empirical Observations to Scientific Principles partitions sintering applications and observations to show critical turning points required to establish modern sintering as a predictive science. This book, written by the most cited author in his field, is laced with people, organizations, critical steps, and important formulations in a mixture of history, personalities, and applications. Exploring how insights in seemingly unrelated fields sparked progress, it is also a teaching tool to show where there is success, where there are problems, and how to organize teams to leapfrog to new applications or plateaus of use. Randall German's Sintering: From Empirical Observations to Scientific Principles is a platform for directly addressing the critical control parameters in these new research and development efforts. Shows how the theories and understanding of sintering were developed and improved over time, and how different products were developed, ultimately leading to important knowledge and lessons for solving real sintering problems Covers all the necessary infrastructure of sintering theory and practice, such as atomic theory, surface energy, microstructure, and measurement and observation tools Introduces the history and development of such early sintered products as porcelain, tungsten lamp filaments, bronze bearings, steel automotive components, platinum crucibles and more

Download or read book Powder Metallurgy written by G. Dowson and published by Springer. This book was released on 1990 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Powder metallurgy, commonly designated by its initial letters asPM or PM, may be defined as the production of useful artefacts from metal powder without passing through the molten state. This introductory text examines the processes by which these powders are produced, and explores their behaviour in the subsequent consolidation stages.

Download or read book Powder Metallurgy written by S. A. Tsukerman and published by Elsevier. This book was released on 2013-10-22 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt: Powder Metallurgy discusses the production of metal powders and other materials made from it. It defines the meaning of metal powders with some illustrations. The book also identifies the processes similar between the production of metal powder and ceramic products. The technology involved and the variation in the process of metallurgy are covered in some chapters of the book. The book enumerates certain advantages in using powder metallurgy over other processes. Methods such as the reduction of the oxides of metals, electrolysis, thermal dissociation, and chemical disintegration are explained. The origin and improvement made on the method are discussed in detail. The goods created using the process are also explained, as well as the types of metals that are being used. A chapter of the book focuses on the flaws of powder metallurgy. The book will provide useful information to metal smiths, chemists, students, and researchers in the field of chemistry.

Download or read book Spark Plasma Sintering of Materials written by Pasquale Cavaliere and published by Springer. This book was released on 2019-02-18 with total page 781 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes spark plasma sintering (SPS) in depth. It addresses fundamentals and material-specific considerations, techniques, and applications across a broad spectrum of materials. The book highlights methods used to consolidate metallic or ceramic particles in very short times. It highlights the production of complex alloys and metal matrix composites with enhanced mechanical and wear properties. Emphasis is placed on the speed of the sintering processes, uniformity in product microstructure and properties, reduced grain growth, the compaction and sintering of materials in one processing step, various materials processing, and high energy efficiency. Current and potential applications in space science and aeronautics, automation, mechanical engineering, and biomedicine are addressed throughout the book.

Download or read book Science of Sintering written by H. Palmour III and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 626 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume, SCIENCE OF SINTERING: NEW DIRECTIONS FOR MATERIALS PROCESSING AND MICROSTRUCTURAL CONTROL, contains the edited Proceedings of the Seventh World Round Table Conference on Sintering, held in Herceg-Novi, Yugoslavia, Aug. 28 - Sept. 1, 1989. It was organized by the International Institute for the Science of Sintering (IISS), headquartered in Belgrade, Yugoslavia. Every fourth year since 1969, the Institute has organized such a Round Table Conference on Sintering; each has taken place at some selected location within Yugoslavia. A separate series of IISS Topical Sintering Symposia (Summer Schools) have also been held at four year intervals, but they have been offset by about two years, so they occur between the main Conferences. As a rule, the Topical Sintering Symposia have been devoted to more specific topics and they also take place in different countries. The aim of these Conferences and their related "Summer Schools" has been to bring together scientists from all over the world who work in various fields of science and technology concerned with sintering and sintered materials. A total of seven IISS Conferences have been held over the period 1969-1989, and they have been supplemented by the four Topical Sintering Symposia held in Yugoslavia, Poland, India and Japan (in 1975, 1979, 1983 and 1987, respectively). This most recent five day Conference addressed the fundamental scientific background as well as the technological state-of-the-art pertinent to science of sintering and high technology sintered materials.

Download or read book Powder Metallurgy and Particulate Materials Processing written by Randall M. German and published by . This book was released on 2005 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Powder Metallurgy Technology written by G. S. Upadhyaya and published by Cambridge Int Science Publishing. This book was released on 1997 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Contents1 INTRODUCTION; 2 METAL POWDER PRODUCTION; 3 METAL POWDER CHARACTERISTICS; 4 METAL POWDER TRE-AMENT; 5 METAL POWDER COMPACT-ION; 6 SINTERING; 7 HOT CONSOLIDATION; 8 SECONDARY TREATMENT; 9 POWDER INJECTION MOULDING; 10 QUALITY CONTROL OF POWDER METALLURGY MATERIALS.

Download or read book Sintering of Ceramics written by Mohamed N. Rahaman and published by CRC Press. This book was released on 2007-07-06 with total page 388 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sintering of Ceramics provides the only comprehensive treatment of the theories and principles of sintering and their application to the production of advanced ceramics with the required target microstructure. Stemming from the author's bestselling text, Ceramic Processing and Sintering, this book includes additional material selected

Download or read book Handbook of Non Ferrous Metal Powders written by Oleg D Neikov and published by Elsevier. This book was released on 2009-02-24 with total page 644 pages. Available in PDF, EPUB and Kindle. Book excerpt: The manufacture and use of the powders of non-ferrous metals has been taking place for many years in what was previously Soviet Russia, and a huge amount of knowledge and experience has built up in that country over the last forty years or so. Although accounts of the topic have been published in the Russian language, no English language account has existed until now. Six prominent academics and industrialists from the Ukraine and Russia have produced this highly-detailed account which covers the classification, manufacturing methods, treatment and properties of the non-ferrous metals ( aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, lead, tin, bismuth, noble metals and earth metals). The result is a formidable reference source for those in all aspects of the metal powder industry. Covers the manufacturing methods, properties and importance of the following metals: aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, noble metals, rare earth metals, lead, tin and bismuth Expert Russian team of authors, all very experienced English translation and update of book previously published in Russian

Download or read book Advances in Powder Metallurgy written by Isaac Chang and published by Elsevier. This book was released on 2013-08-31 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt: Powder metallurgy (PM) is a popular metal forming technology used to produce dense and precision components. Different powder and component forming routes can be used to create an end product with specific properties for a particular application or industry. Advances in powder metallurgy explores a range of materials and techniques used for powder metallurgy and the use of this technology across a variety of application areas. Part one discusses the forming and shaping of metal powders and includes chapters on atomisation techniques, electrolysis and plasma synthesis of metallic nanopowders. Part two goes on to highlight specific materials and their properties including advanced powdered steel alloys, porous metals and titanium alloys. Part three reviews the manufacture and densification of PM components and explores joining techniques, process optimisation in powder component manufacturing and non-destructive evaluation of PM parts. Finally, part four focusses on the applications of PM in the automotive industry and the use of PM in the production of cutting tools and biomaterials. Advances in powder metallurgy is a standard reference for structural engineers and component manufacturers in the metal forming industry, professionals working in industries that use PM components and academics with a research interest in the field. Discusses the forming and shaping of metal powders and includes chapters on atomisation techniques Highlights specific materials and their properties including advanced powdered steel alloys, porous metals and titanium alloys Reviews the manufacture and densification of PM components and explores joining techniques

Download or read book Liquid Phase Sintering written by R.M. German and published by Springer Science & Business Media. This book was released on 2013-12-14 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the past few years there has been rapid growth in the activities involving particulate materials because of recognized advantages in manufacturing. This growth is attributed to several factors; i) an increased concern over energy utilization, ii) a desire to better control microstructure in engineermg materials, iii) the need for 1mproved material economy, iv) societal and economic pressures for higher productivity and quality, v) requirements for unique property combinations for high performance applica tions, and vi) a desire for net shape forming. Accordingly, liquid phase sintering has received increased attention as part of the growth in particulate materials processing. As a consequence, the commercial applications for liquid phase sintering are expanding rapidly. This active and expanding interest is not well served by available texts. For this reason I felt it was appropriate to write this book on liquid phase sintering. The technology of liquid phase sintering IS quite old and has been in use in the ceramics industry for many centuries. However, the general perception among materials and manufacturing engineers is that liquid phase sintering is still a novel technique. I believe the diverse technological appli cations outlined in this book will dispel I such impressions. Liquid phase. sintering has great value in fabricating several unique materials to near net shapes and will continue to expand in applications as the fundamental attrib utes are better appreciated. I am personally involved with several uses for liquid phase sintering.