Download or read book Single phase Liquid Flow and Heat Transfer in Plain and Enhanced Silicon Microchannels written by Mark E. Steinke and published by . This book was released on 2005 with total page 520 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Microscale heat transfer and microfluidics have become increasingly important to overcome some very complex engineering challenges. The use of very small passages to gain heat transfer enhancement is a well documented method for achieving high heat flux dissipation. However, some interesting experimental results have caused researchers to question if the conventional theories for fluid flow and heat transfer are valid in the microscale passages. However, there is no significant physical basis for the discrepancies with single-phase liquid flows when the passage is scaled to the microscale. The present work identifies the sources of the discrepancies reported in literature and provides a method to correct for them. In the course of this pursuit, a new experimental facility is developed to generate highly accurate experimental data for single-phase flow of water. The new experimental data are used to highlight the sources of discrepancies and illustrate a course of action to correct for them. Finally, a novel method for creating even greater heat transfer enhancement has been realized. Small offset fins have been fabricated in silicon microchannels in order to create a constantly developing flow in the microchannel heat exchanger and thus heat transfer enhancement. A new parameter based upon the heat flux dissipated and the pressure drop required is developed to aid in the comparison between these enhanced silicon microchannels and plain geometry silicon microchannels. The result is an order of magnitude increase in thermal performance with a marginal increase in overall pressure drop"--Abstract.
Download or read book Fluid Flow Heat Transfer and Boiling in Micro Channels written by L. P. Yarin and published by Springer Science & Business Media. This book was released on 2008-09-19 with total page 487 pages. Available in PDF, EPUB and Kindle. Book excerpt: The subject of the book is uid dynamics and heat transfer in micro-channels. This problem is important for understanding the complex phenomena associated with single- and two-phase ows in heated micro-channels. The challenge posed by high heat uxes in electronic chips makes thermal management a key factor in the development of these systems. Cooling of mic- electronic components by new cooling technologies, as well as improvement of the existing ones, is becoming a necessity as the power dissipation levels of integrated circuits increases and their sizes decrease. Miniature heat sinks with liquid ows in silicon wafers could signi cantly improve the performance and reliability of se- conductor devices. The improvements are made by increasing the effective thermal conductivity, by reducing the temperature gradient across the wafer, by reducing the maximum wafer temperature, and also by reducing the number and intensity of localized hot spots. A possible way to enhance heat transfer in systems with high power density is to change the phase in the micro-channels embedded in the device. This has motivated a number of theoretical and experimental investigations covering various aspects of heat transfer in micro-channel heat sinks with phase change. The ow and heat transfer in heated micro-channels are accompanied by a n- ber of thermohydrodynamic processes, such as liquid heating and vaporization, bo- ing, formation of two-phase mixtures with a very complicated inner structure, etc., which affect signi cantly the hydrodynamic and thermal characteristics of the co- ing systems.
Download or read book Silicon Microchannel Heat Sinks written by Lian Zhang and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: Two-phase microchannel cooling is one of the most promising thermal-management technologies for future high-power IC chips. Understanding the boiling process and the two-phase-flow behavior in microchannels is the key to successful implementation of a microchannel heat sink. This book focuses on the phase-change phenomena and the heat transfer in sub-150 nm diameter silicon microchannels, with emphasis on thermal measurement and modeling, and the impact of small dimensions on two-phase flow regimes.
Download or read book Heat Transfer and Fluid Flow in Minichannels and Microchannels written by Satish Kandlikar and published by Butterworth-Heinemann. This book was released on 2013-10-25 with total page 588 pages. Available in PDF, EPUB and Kindle. Book excerpt: Heat exchangers with minichannel and microchannel flow passages are becoming increasingly popular due to their ability to remove large heat fluxes under single-phase and two-phase applications. Heat Transfer and Fluid Flow in Minichannels and Microchannels methodically covers gas, liquid, and electrokinetic flows, as well as flow boiling and condensation, in minichannel and microchannel applications. Examining biomedical applications as well, the book is an ideal reference for anyone involved in the design processes of microchannel flow passages in a heat exchanger. Each chapter is accompanied by a real-life case study New edition of the first book that solely deals with heat and fluid flow in minichannels and microchannels Presents findings that are directly useful to designers; researchers can use the information in developing new models or identifying research needs
Download or read book Heat Transfer and Fluid Flow in Minichannels and Microchannels written by Satish Kandlikar and published by Elsevier. This book was released on 2006 with total page 492 pages. Available in PDF, EPUB and Kindle. Book excerpt: &Quot;This book explores flow through passages with hydraulic diameters from about 1 [mu]m to 3 mm, covering the range of minichannels and microchannels. Design equations along with solved examples and practice problems are also included to serve the needs of practicing engineers and students in a graduate course."--BOOK JACKET.
Download or read book Experimental and Numerical Evaluation of Single Phase Adiabatic Flows in Plain and Enhanced Microchannels written by Akhilesh V. Bapat and published by . This book was released on 2007 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Thermal dissipation is a critical issue in the performance of semiconductor devices. The current practice is to use forced convection by air over a heat sink which is bonded to the microelectronic device. With increased packing density of the circuits inside a chip, large amounts of heat is generated and air cooling is no longer sufficient. Forced liquid convection using microchannels is considered to be a viable option for cooling of these microprocessor chips. This work deals with the evaluation of the single phase pressure drop in microchannels. There are two types of microchannels under consideration. Plain microchannels which have basically long uninterrupted flow channels while the enhanced channels which have the interrupted flow lengths. Enhanced microchannels, because of their offset strip fin geometry, significantly increase both the heat transfer as well as the pressure drop. This work deals with the evaluation of single phase flow pressure drop in both plain and enhanced microchannels. For plain microchannels there have been a few investigations in the literature which suggest that the microchannel performance can generally be predicted using the classical fluid flow equations. However there are some experiments that still show departure from the classical theory that cannot be explained. It is proposed in this work that the reason for this discrepancy can be traced to the effects due to flow maldistribution in plain microchannels. A systematic experimental investigation is performed to study the effects of slight variations in channel dimensions and their influence on the flow maldistribution in an attempt to validate the applicability of classical theory to microchannel flows. Enhanced microchannels however have not been investigated thoroughly. There is very few data available in the literature. FLUENT is a CFD software which can be used as a tool to design and optimize these enhanced channels. However it has to be first validated with experiments. Thus pressure drop experiments are carried out on an offset strip fin silicon microchannel and the data is predicted using FLUENT, which is CFD software. Also existing predictive models for friction factor in offset strip fin minichannels are tested to check their validity for microchannel flows. For plain microchannels, it seen that with uniform flow assumption, the friction factor is either underpredicted or overpredicted using the theory depending upon the reference channel dimension. However by accounting flow maldistribution in plain microchannels, friction factor can be accurately determined using theoretical equations. For enhanced microchannels it is observed that FLUENT can predict the pressure drop within 10%. In this work only adiabatic flows are considered. It is recommended that this work should be extended to flows with heat transfer"--Abstract.
Download or read book Phase Separation in Two phase Microfluidic Heat Exchangers written by Milnes P. David and published by Stanford University. This book was released on 2011 with total page 151 pages. Available in PDF, EPUB and Kindle. Book excerpt: Two-phase microfluidic heat exchangers have the potential to meet the large heat dissipation demands of high power electronics and computing systems. Two-phase cooling systems face practical challenges brought on by the growth and advection of the vapor phase in the confined geometries, which lead to large pressure drops, increased thermal resistance and the formation of detrimental flow instabilities. One proposed solution to these issues is phase separation, whereby the vapor is locally separated from the two-phase flow through a porous hydrophobic membrane. This dissertation describes a series of studies conducted to develop an understanding of the factors that influence vapor separation and its impact on the hydraulic and thermal characteristics of two-phase heat exchangers. Flow phenomena are a critical component in developing this understanding of phase separation. High speed visualization of adiabatic and diabatic vaporizing flows was carried out in a single 124[Mu]m by 98[Mu]m copper microchannel with a 65[Mu]m thick, 220nm pore diameter hydrophobic PTFE membrane wall. During adiabatic air-water flow, wavy-stratified and stratified flow dominated lower liquid velocities, while plug and annular type flows dominated at the higher velocities. Analysis found that air removal could be improved by increasing the venting area, increasing the trans-membrane pressure or using thinner, high permeability membranes. Diabatic water-vapor experiments with mass flux velocities of 140 and 340 kg/s-m2 and exit qualities up to 20% found that stratified type flows dominate at lower mass fluxes while cyclical churn-annular flow became more prevalent at the higher mass-flux and quality. The observed flow regimes are hypothesized to play a significant role in determining the pressure drop and heat transfer coefficient during flow boiling. To study the impact of various geometric and membrane factors on the performance of a phase separating microchannel heat exchanger dissipating 100W of heat, a numerical model incorporating vapor separation and transport during two-phase flow boiling in a microchannel was developed. The impact of substrate thermal conductivity and thickness, membrane permeability and thickness, liquid channel density, liquid and vent channel diameter and vent-to-liquid channel diameter ratio was studied and compared for a standard non-venting heat exchanger, a vapor venting heat exchanger and a non-venting heat exchanger occupying the same increased volume as the venting heat exchanger. The numerical study found that the venting heat exchanger had improved pressure drop and device temperatures for all tested conditions when compared against a standard heat exchanger but only under very limited conditions when compared against the volumetrically equivalent non-venting heat exchanger. The study indicates that the best venting heat exchanger performance is achieved when the membrane conductance is of the same order or higher than that of the microchannel; this can be achieved through the use of thin high permeability membranes coupled with small hydraulic diameter microchannels. Finally, a study was conducted to explore the fabrication methods to build a vapor separating heat exchanger and to quantify the operating performance of multichannel silicon and copper phase separating devices. A copper parallel microchannel heat exchanger with nineteen 130[Mu]m square microchannels was built and tested at heat fluxes of up to 820 kW/m2 and water mass fluxes of between 102 and 420 kg/s-m2. Normalized pressure drop was improved by as much as 60% and average substrate temperature by a maximum of 4.4°C between the non-venting control and vapor venting device under similar operating conditions. Comparison between the experimental results and simulation predictions found higher than expected pressure drop improvements at higher mass fluxes and poorer heat transfer coefficients at the lowest mass flux. Based on the flow phenomena study these discrepancies are believed to be due to the mass flux and vapor quality dependent two-phase flow structures. The encouraging experimental and numerical results motivate further study into phase separation methods, materials and flow physics. The development of a high performance phase separating heat exchanger, with the thermal benefits of two-phase boiling flow and the hydraulic benefits of single-phase liquid flow, would strongly enable the adoption and application of two-phase heat exchangers to provide effective and efficient cooling for next generation high power computing systems.
Download or read book Fluid Flow and Heat Transfer of Liquid liquid Taylor Flow in Microchannels written by Ayoub Abdollahi and published by . This book was released on 2019 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: Microfluidic devices are increasingly finding use in engineering applications due to their abilities in thermal management, and their enabling of better flow control. Applications include electronic cooling, microscale heat exchangers, and microreactors. While a number of numerical and experimental studies were found on single phase flow in microchannels, only a few studies have focused on the application of Taylor droplet flow within microchannels. Taylor droplet flow is characterised by periodically organised droplets in a carrier fluid, and has been shown to offer greatly enhanced rates of heat transfer over single phase flow. The practical realisation of the Taylor droplet system however requires generation of knowledge on its behaviour in square and rectangular microchannels. This thesis therefore focuses on understanding the fluid flow and heat transfer behaviour of Taylor droplet flow with no phase change in square microchannels using computational fluid dynamics (CFD) modelling, and experimental techniques. In this study, experiments were carried out in a stainless steel microchannel with a square cross section, having a hydraulic diameter of 2mm. To enable these studies, an experimental test rig was developed with three main sections: a T-junction section that allows Taylor fluid flow to be generated, a test section for heat transfer and pressure drop measurements, and a transparent visualization section. This test rig allowed heat transfer experiments to be performed while simultaneously visualising the Taylor droplet flow. The experiments were performed for single phase fluid flow and liquid-liquid Taylor droplet flow. In order to extend the understanding of the hydrodynamic and thermal behavior of single phase and Taylor flows in microchannels, a series of numerical simulations are performed that matched the experimental conditions. Three-dimensional numerical simulations were carried out using a volume of fluid (VOF) method with the commercial computational fluid dynamics (CFD) software package, ANSYS Fluent, Release 17.0. The effect of some critical dimensionless groups on the accuracy of the estimates of the heat transfer rate was studied. Discrepancies were found between experimental measurements of Nusselt number and theoretical predictions, particularly at low Reynolds numbers (Re
Download or read book Compact Heat Exchangers written by Alexander Louis London and published by CRC Press. This book was released on 1990 with total page 798 pages. Available in PDF, EPUB and Kindle. Book excerpt: Heat exchangers are a crucial part of aerospace, marine, cryogenic and refrigeration technology. These essays cover such topics as complicated flow arrangements, complex extended surfaces, two-phase flow and irreversibility in heat exchangers, and single-phase heat transfer.
Download or read book Two phase Flow and Heat Transfer written by David Butterworth and published by . This book was released on 1979 with total page 514 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Laminar Flow Forced Convection in Ducts written by R. K. Shah and published by Academic Press. This book was released on 2014-06-28 with total page 492 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laminar Flow Forced Convection in Ducts is a sourcebook for compact heat exchanger analytical data. This book describes the analytical solutions for laminar fluid flow and forced convection heat transfer in circular and noncircular pipes, including applicable differential equations and boundary conditions involving velocity and temperature problems of fluid flow. The book also discusses fluid flow—how much power is required to pump fluids through the heat exchanger, as well as the heat transfer—the determination of q" distribution, and the temperature of fluid and walls. The text also analyzes the coolant or heat transfer fluid flows in a nuclear power reactor composed of a bundle of circular section fuel rods located inside a round tube. R.A. Axford addresses fluid flow and heat transfers results for the rod bundle geometry in "Heat Transfer in Rod Bundles." The book also provides an overview and guidelines that can be used for the designer and the applied mathematician. This book is suitable for engineers working in electronics, aerospace, instrumentation, and biomechanics that use cooling or heating exchanges or solar collection systems.
Download or read book Wo phase and Single phase Heat Transfer and Fluid Flow Through Enhanced Surfaces and in Microgeometries written by Simone Mancin and published by . This book was released on 2009 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Clean Energy Systems 6 Volume Set written by Jinyue Yan and published by John Wiley & Sons. This book was released on 2015-06-22 with total page 4038 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Handbook of Clean Energy Systems brings together an international team of experts to present a comprehensive overview of the latest research, developments and practical applications throughout all areas of clean energy systems. Consolidating information which is currently scattered across a wide variety of literature sources, the handbook covers a broad range of topics in this interdisciplinary research field including both fossil and renewable energy systems. The development of intelligent energy systems for efficient energy processes and mitigation technologies for the reduction of environmental pollutants is explored in depth, and environmental, social and economic impacts are also addressed. Topics covered include: Volume 1 - Renewable Energy: Biomass resources and biofuel production; Bioenergy Utilization; Solar Energy; Wind Energy; Geothermal Energy; Tidal Energy. Volume 2 - Clean Energy Conversion Technologies: Steam/Vapor Power Generation; Gas Turbines Power Generation; Reciprocating Engines; Fuel Cells; Cogeneration and Polygeneration. Volume 3 - Mitigation Technologies: Carbon Capture; Negative Emissions System; Carbon Transportation; Carbon Storage; Emission Mitigation Technologies; Efficiency Improvements and Waste Management; Waste to Energy. Volume 4 - Intelligent Energy Systems: Future Electricity Markets; Diagnostic and Control of Energy Systems; New Electric Transmission Systems; Smart Grid and Modern Electrical Systems; Energy Efficiency of Municipal Energy Systems; Energy Efficiency of Industrial Energy Systems; Consumer Behaviors; Load Control and Management; Electric Car and Hybrid Car; Energy Efficiency Improvement. Volume 5 - Energy Storage: Thermal Energy Storage; Chemical Storage; Mechanical Storage; Electrochemical Storage; Integrated Storage Systems. Volume 6 - Sustainability of Energy Systems: Sustainability Indicators, Evaluation Criteria, and Reporting; Regulation and Policy; Finance and Investment; Emission Trading; Modeling and Analysis of Energy Systems; Energy vs. Development; Low Carbon Economy; Energy Efficiencies and Emission Reduction. Key features: Comprising over 3,500 pages in 6 volumes, HCES presents a comprehensive overview of the latest research, developments and practical applications throughout all areas of clean energy systems, consolidating a wealth of information which is currently scattered across a wide variety of literature sources. In addition to renewable energy systems, HCES also covers processes for the efficient and clean conversion of traditional fuels such as coal, oil and gas, energy storage systems, mitigation technologies for the reduction of environmental pollutants, and the development of intelligent energy systems. Environmental, social and economic impacts of energy systems are also addressed in depth. Published in full colour throughout. Fully indexed with cross referencing within and between all six volumes. Edited by leading researchers from academia and industry who are internationally renowned and active in their respective fields. Published in print and online. The online version is a single publication (i.e. no updates), available for one-time purchase or through annual subscription.
Download or read book Flow boiling and condensation in microscale channels written by Fabio Toshio Kanizawa and published by Springer Nature. This book was released on 2021-04-30 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers aspects of multiphase flow and heat transfer during phase change processes, focusing on boiling and condensation in microscale channels. The authors present up-to-date predictive methods for flow pattern, void fraction, pressure drop, heat transfer coefficient and critical heat flux, pointing out the range of operational conditions that each method is valid. The first four chapters are dedicated on the motivation to study multiphase flow and heat transfer during phase change process, and the three last chapters are focused on the analysis of heat transfer process during boiling and condensation. During the description of the models and predictive methods, the trends are discussed and compared with experimental findings.
Download or read book VDI Heat Atlas written by VDI Gesellschaft and published by Springer Science & Business Media. This book was released on 2010-07-21 with total page 1608 pages. Available in PDF, EPUB and Kindle. Book excerpt: For more than 50 years, the Springer VDI Heat Atlas has been an indispensable working means for engineers dealing with questions of heat transfer. Featuring 50% more content, this new edition covers most fields of heat transfer in industrial and engineering applications. It presents the interrelationships between basic scientific methods, experimental techniques, model-based analysis and their transfer to technical applications.
Download or read book Critical Heat Flux in Flow Boiling in Microchannels written by Sujoy Kumar Saha and published by Springer. This book was released on 2015-06-04 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Brief concerns the important problem of critical heat flux in flow boiling in microchannels. A companion edition in the SpringerBrief Subseries on Thermal Engineering and Applied Science to “Heat Transfer and Pressure Drop in Flow Boiling in Microchannels,” by the same author team, this volume is idea for professionals, researchers, and graduate students concerned with electronic cooling.
Download or read book Phase Separation in Two phase Microfluidic Heat Exchangers written by Milnes P. David and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Two-phase microfluidic heat exchangers have the potential to meet the large heat dissipation demands of high power electronics and computing systems. Two-phase cooling systems face practical challenges brought on by the growth and advection of the vapor phase in the confined geometries, which lead to large pressure drops, increased thermal resistance and the formation of detrimental flow instabilities. One proposed solution to these issues is phase separation, whereby the vapor is locally separated from the two-phase flow through a porous hydrophobic membrane. This dissertation describes a series of studies conducted to develop an understanding of the factors that influence vapor separation and its impact on the hydraulic and thermal characteristics of two-phase heat exchangers. Flow phenomena are a critical component in developing this understanding of phase separation. High speed visualization of adiabatic and diabatic vaporizing flows was carried out in a single 124[Mu]m by 98[Mu]m copper microchannel with a 65[Mu]m thick, 220nm pore diameter hydrophobic PTFE membrane wall. During adiabatic air-water flow, wavy-stratified and stratified flow dominated lower liquid velocities, while plug and annular type flows dominated at the higher velocities. Analysis found that air removal could be improved by increasing the venting area, increasing the trans-membrane pressure or using thinner, high permeability membranes. Diabatic water-vapor experiments with mass flux velocities of 140 and 340 kg/s-m2 and exit qualities up to 20% found that stratified type flows dominate at lower mass fluxes while cyclical churn-annular flow became more prevalent at the higher mass-flux and quality. The observed flow regimes are hypothesized to play a significant role in determining the pressure drop and heat transfer coefficient during flow boiling. To study the impact of various geometric and membrane factors on the performance of a phase separating microchannel heat exchanger dissipating 100W of heat, a numerical model incorporating vapor separation and transport during two-phase flow boiling in a microchannel was developed. The impact of substrate thermal conductivity and thickness, membrane permeability and thickness, liquid channel density, liquid and vent channel diameter and vent-to-liquid channel diameter ratio was studied and compared for a standard non-venting heat exchanger, a vapor venting heat exchanger and a non-venting heat exchanger occupying the same increased volume as the venting heat exchanger. The numerical study found that the venting heat exchanger had improved pressure drop and device temperatures for all tested conditions when compared against a standard heat exchanger but only under very limited conditions when compared against the volumetrically equivalent non-venting heat exchanger. The study indicates that the best venting heat exchanger performance is achieved when the membrane conductance is of the same order or higher than that of the microchannel; this can be achieved through the use of thin high permeability membranes coupled with small hydraulic diameter microchannels. Finally, a study was conducted to explore the fabrication methods to build a vapor separating heat exchanger and to quantify the operating performance of multichannel silicon and copper phase separating devices. A copper parallel microchannel heat exchanger with nineteen 130[Mu]m square microchannels was built and tested at heat fluxes of up to 820 kW/m2 and water mass fluxes of between 102 and 420 kg/s-m2. Normalized pressure drop was improved by as much as 60% and average substrate temperature by a maximum of 4.4°C between the non-venting control and vapor venting device under similar operating conditions. Comparison between the experimental results and simulation predictions found higher than expected pressure drop improvements at higher mass fluxes and poorer heat transfer coefficients at the lowest mass flux. Based on the flow phenomena study these discrepancies are believed to be due to the mass flux and vapor quality dependent two-phase flow structures. The encouraging experimental and numerical results motivate further study into phase separation methods, materials and flow physics. The development of a high performance phase separating heat exchanger, with the thermal benefits of two-phase boiling flow and the hydraulic benefits of single-phase liquid flow, would strongly enable the adoption and application of two-phase heat exchangers to provide effective and efficient cooling for next generation high power computing systems.
