Download or read book Seismic Control Systems written by S. Syngellakis and published by WIT Press. This book was released on 2013 with total page 209 pages. Available in PDF, EPUB and Kindle. Book excerpt: Earthquakes remain largely unpredictable and potentially catastrophic, a matter of continuous concern to communities in affected zones. Scientists and engineers have made a considerable effort to mitigate their consequences through the design of effective protective devices. New concepts have recently been developed to address the requirements for better structural performance and a more effective use of new materials at a lower cost.This book disseminates knowledge and increases awareness on this very critical subject and thus ultimately contributes to a safer structural design against earthquakes. It comprises a number of articles taken from recent editions of Transactions of the Wessex Institute covering a wide range of topics within the subject of seismic protection through vibration control devices.The first four papers provide a very comprehensive review of existing seismic control designs highlighting their variety, the effectiveness of their performance, as well as the extent of their use for the protection of various types of structures world wide. Most articles deal with anti-seismic devices implementing passive control of structural response through seismic isolation and energy dissipation. Testing and modelling energy-dissipating systems are also extensively covered in the book.It is also important to understand how existing structures fitted with seismic control devices perform against earthquakes. Two such case studies are included in the book; a roof isolated from the top of an existing structure and a bridge supported on both isolating and damping systems. Finally, new analytical approaches for optimising the performance of tuned mass dampers are detailed in two companion papers.
Download or read book Integrated Seismic Design of Structure and Control Systems written by Paolo Castaldo and published by Springer Science & Business Media. This book was released on 2013-11-26 with total page 220 pages. Available in PDF, EPUB and Kindle. Book excerpt: The structural optimization procedure presented in this book makes it possible to achieve seismic protection through integrated structural/control system design. In particular, it is explained how slender structural systems with a high seismic performance can be achieved through inclusion of viscous and viscoelastic dampers as an integral part of the system. Readers are provided with essential introductory information on passive structural control and passive energy dissipation systems. Dynamic analyses of both single and multiple degree of freedom systems are performed in order to verify the achievement of pre-assigned performance targets, and it is explained how the optimal integrated design methodology, also relevant to retrofitting of existing buildings, should be applied. The book illustrates how structural control research is opening up new possibilities in structural forms and configurations without compromising structural performance.
Download or read book Smart Structures written by Franklin Y. Cheng and published by CRC Press. This book was released on 2008-02-25 with total page 672 pages. Available in PDF, EPUB and Kindle. Book excerpt: An innovative concept, smart structural systems have proven to be extremely effective in absorbing damaging energy and/or counteracting potentially devastating force, thus limiting structural collapse and subsequent injury. As this technology rapidly evolves, there is an ever-increasing need for an authoritative reference that will allow those in t
Download or read book Design Optimization of Active and Passive Structural Control Systems written by Lagaros, Nikos D. and published by IGI Global. This book was released on 2012-08-31 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt: A typical engineering task during the development of any system is, among others, to improve its performance in terms of cost and response. Improvements can be achieved either by simply using design rules based on the experience or in an automated way by using optimization methods that lead to optimum designs. Design Optimization of Active and Passive Structural Control Systems includes Earthquake Engineering and Tuned Mass Damper research topics into a volume taking advantage of the connecting link between them, which is optimization. This is a publication addressing the design optimization of active and passive control systems. This title is perfect for engineers, professionals, professors, and students alike, providing cutting edge research and applications.
Download or read book Building Control with Passive Dampers written by Izuru Takewaki and published by John Wiley & Sons. This book was released on 2011-09-23 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: The recent introduction of active and passive structural control methods has given structural designers powerful tools for performance-based design. However, structural engineers often lack the tools for the optimal selection and placement of such systems. In Building Control with Passive Dampers , Takewaki brings together most the reliable, state-of-the-art methods in practice around the world, arming readers with a real sense of how to address optimal selection and placement of passive control systems. The first book on optimal design, sizing, and location selection of passive dampers Combines theory and practical applications Describes step-by-step how to obtain optimal damper size and placement Covers the state-of-the-art in optimal design of passive control Integrates the most reliable techniques in the top literature and used in practice worldwide Written by a recognized expert in the area MATLAB code examples available from the book’s Companion Website This book is essential for post-graduate students, researchers, and design consultants involved in building control. Professional engineers and advanced undergraduates interested in seismic design, as well as mechanical engineers looking for vibration damping techniques, will also find this book a helpful reference. Code examples available at www.wiley.com/go/takewaki
Download or read book Passive and Active Structural Vibration Control in Civil Engineering written by T.T. Soong and published by Springer. This book was released on 2014-05-04 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: Base isolation, passive energy dissipation and active control represent three innovative technologies for protection of structures under environmental loads. Increasingly, they are being applied to the design of new structures or to the retrofit of existing structures against wind, earthquakes and other external loads. This book, with contributions from leading researchers from Japan, Europe, and the United States, presents a balanced view of current research and world-wide development in this exciting and fast expanding field. Basic principles as well as practical design and implementational issues associated with the application of base isolation systems and passive and active control devices to civil engineering structures are carefully addressed. Examples of structural applications are presented and extensively discussed.
Download or read book Earthquake Resistant Design of Buildings written by Muhammad Hadi and published by CRC Press. This book was released on 2017-10-06 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introducing important concepts in the study of earthquakes related to retrofitting of structures to be made earthquake resistant. The book investigates the pounding effects on base-isolated buildings, the soil-structure-interaction effects on adjacent buildings due to the impact, the seismic protection of adjacent buildings and the mitigation of earthquakeinduced vibrations of two adjacent structures. These concepts call for a new understanding of controlled systems with passive-active dampers and semi-active dampers. The passive control strategy of coupled buildings is investigated for seismic protection in comparison to active and semi-active control strategies.
Download or read book Response Control and Seismic Isolation of Buildings written by Masahiko Higashino and published by Routledge. This book was released on 2006-09-27 with total page 414 pages. Available in PDF, EPUB and Kindle. Book excerpt: This state of the art report from an international task group (TG44) of CIB, the International Council of Building Research Organizations, presents a highly authoritative guide to the application of innovative technologies on response control and seismic isolation of buildings to practice worldwide. Many countries and cities are located in earthquake-prone areas making effective seismic design a major issue in structural engineering. Reassuringly, structural response control and seismic isolation have advanced remarkably in recent years following numerous studies internationally. Several major conferences have been held and reports have been written but little has been issued on the application of the technologies to good structural engineering practice. Plugging that gap, Response Control and Seismic Isolation of Buildings presents researchers in structural engineering (dynamics) and construction management with up-to-date applications of the latest technologies.
Download or read book Seismic Isolation and Response Control written by Eftychia Apostolidi and published by International Association for Bridge and Structural Engineering. This book was released on 2021-12-15 with total page 111 pages. Available in PDF, EPUB and Kindle. Book excerpt: The seismic resilience of new and existing structures is a key priority for the protection of human lives and the reduction of economic losses in earthquake prone areas. The modern seismic codes have focused on the upgrade of the structural performance of the new and existing structures. However, in many cases it is preferrable to mitigate the effects of the earthquakes by reducing the induced loads in the structures using seismic isolation and response control devices. The limited expertise in the selection and design of the appropriate system for new and existing structures is the main challenge for an extensive use of seismic isolation and response control systems in practice. This document aims to provide a practical guide by presenting a collection of the most commonly used seismic isolation and response control systems and a critical evaluation of the main characteristics of these systems. Comparisons of the key parameters of the design processes for new buildings with seismic isolation are presented, while the application of seismic isolation systems and response control systems for the retrofitting of existing structures is also examined, followed by various case studies from Greece, Japan, Mexico, New Zealand, and Turkey.
Download or read book Textbook of Seismic Design written by G. R. Reddy and published by Springer. This book was released on 2019-08-03 with total page 553 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the seismic design of Structures, Piping Systems and Components (SSC). It explains the basic mechanisms of earthquakes, generation of design basis ground motion, and fundamentals of structural dynamics; further, it delves into geotechnical aspects related to the earthquake design, analysis of multi degree-of-freedom systems, and seismic design of RC structures and steel structures. The book discusses the design of components and piping systems located at the ground level as well as at different floor levels of the structure. It also covers anchorage design of component and piping system, and provides an introduction to retrofitting, seismic response control including seismic base isolation, and testing of SSCs. The book is written in an easy-to-understand way, with review questions, case studies and detailed examples on each topic. This educational approach makes the book useful in both classrooms and professional training courses for students, researchers, and professionals alike.
Download or read book Recent Advances and Applications of Seismic Isolation and Energy Dissipation Devices written by Dario De Domenico and published by Frontiers Media SA. This book was released on 2020-10-12 with total page 263 pages. Available in PDF, EPUB and Kindle. Book excerpt: This eBook is a collection of articles from a Frontiers Research Topic. Frontiers Research Topics are very popular trademarks of the Frontiers Journals Series: they are collections of at least ten articles, all centered on a particular subject. With their unique mix of varied contributions from Original Research to Review Articles, Frontiers Research Topics unify the most influential researchers, the latest key findings and historical advances in a hot research area! Find out more on how to host your own Frontiers Research Topic or contribute to one as an author by contacting the Frontiers Editorial Office: frontiersin.org/about/contact.
Download or read book Structural Dynamic Systems Computational Techniques and Optimization written by Cornelius T. Leondes and published by Elsevier. This book was released on 1999 with total page 262 pages. Available in PDF, EPUB and Kindle. Book excerpt: Conventional seismic design has been based on structural strength in the initial design of structures, resulting in lateral force resisting systems with sufficient strength to be able to absorb and dissipate the seismic. For important structures such as urban high speed road systems, high rise buildings, hospitals, airports and other essential structures which must be quite functional after an earthquake, modern seismic structural design techniques have been developed with a view toward eliminating or significantly reducing seismic damage to such structures. This volume is a comprehensive treatment of the issues involved in modern seismic design techniques for structure with a view to significantly enhancing their capability of surviving earthquakes to an adequate degree, i.e., enhancing the ability of structural systems to withstand high level earthquakes.
Download or read book Design of Seismic Isolated Structures written by Farzad Naeim and published by John Wiley & Sons. This book was released on 1999-03-25 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt: Um die Auswirkungen von Erdbeben auf Gebäude, Brücken und andere empfindliche Konstruktionen zu mildern, wurden im Laufe der Jahre zahlreiche Technologien entwickelt. Eine der neueren hiervon ist die seismische Isolation: Sie beinhaltet den Einbau von Mechanismen, die das Gebäude von den Bewegungen des Untergrunds entkoppeln. Der Erfolg dieser Technik übertrifft den aller vorher bekannten Verfahren - ein Grund für Ingenieure und Architekten, sich genauer zu informieren. Dazu sei dieses Buch empfohlen. (04/99)
Download or read book Wind and Seismic Effects written by United States-Japan Cooperative Program in Natural Resources. Panel on Wind and Seismic Effects. Joint Meeting and published by . This book was released on 1992 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book NEHRP Commentary on the Gidelines for the Seismic Rehabilitation of Buildings written by Eugene Zeller and published by DIANE Publishing. This book was released on 2000-06 with total page 500 pages. Available in PDF, EPUB and Kindle. Book excerpt: This document from the National Earthquake Hazards Reduction Program (NEHRP) was prepared for the Building Seismic Safety Council (BSSC) with funding from the Federal Emergency Management Agency (FEMA). It provides commentary on the NEHRP Guidelines for the Seismic Rehabilitation of Buildings. It contains systematic guidance enabling design professionals to formulate effective & reliable rehabilitation approaches that will limit the expected earthquake damage to a specified range for a specified level of ground shaking. This kind of guidance applicable to all types of existing buildings & in all parts of the country has never existed before. Illustrated.
Download or read book Earthquake Resistant Design with Rubber written by James M. Kelly and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 134 pages. Available in PDF, EPUB and Kindle. Book excerpt: My involvement in the use of natural rubber as a method for the protec 1976. At that time, tion of buildings against earthquake attack began in I was working on the development of energy-dissipating devices for the same purpose and had developed and tested a device that was even tually used in a stepping-bridge structure, this being a form of partial isolation. It became clear to me that in order to use these energy devices for the earthquake protection of buildings, it would be best to combine them with an isolation system which would give them the large displace ments needed to develop sufficient hysteresis. At this appropriate point in time, I was approached by Dr. C. J. Derham, then of the Malaysian Rubber Producers' Research Association (MRPRA), who asked if I was interested in looking at the possibility of conducting shaking table tests at the Earthquake Simulator Laboratory to see to what extent natural rubber bearings could be used to protect buildings from earthquakes. Very soon after this meeting, we were able to do such a test using a 20-ton model and hand-made isolators. The eady tests were very promising. Accordingly, a further set of tests was done with a more realistic five storey model weighing 40 tons with bearings that were commercially made. In both of the test series, the isolators were used both alone and with a number of different types of energy-dissipating devices to en hance damping.
Download or read book Seismic Analysis of Structures written by T. K. Datta and published by John Wiley & Sons. This book was released on 2010-03-16 with total page 472 pages. Available in PDF, EPUB and Kindle. Book excerpt: While numerous books have been written on earthquakes, earthquake resistance design, and seismic analysis and design of structures, none have been tailored for advanced students and practitioners, and those who would like to have most of the important aspects of seismic analysis in one place. With this book, readers will gain proficiencies in the following: fundamentals of seismology that all structural engineers must know; various forms of seismic inputs; different types of seismic analysis like, time and frequency domain analyses, spectral analysis of structures for random ground motion, response spectrum method of analysis; equivalent lateral load analysis as given in earthquake codes; inelastic response analysis and the concept of ductility; ground response analysis and seismic soil structure interaction; seismic reliability analysis of structures; and control of seismic response of structures. Provides comprehensive coverage, from seismology to seismic control Contains useful empirical equations often required in the seismic analysis of structures Outlines explicit steps for seismic analysis of MDOF systems with multi support excitations Works through solved problems to illustrate different concepts Makes use of MATLAB, SAP2000 and ABAQUAS in solving example problems of the book Provides numerous exercise problems to aid understanding of the subject As one of the first books to present such a comprehensive treatment of the topic, Seismic Analysis of Structures is ideal for postgraduates and researchers in Earthquake Engineering, Structural Dynamics, and Geotechnical Earthquake Engineering. Developed for classroom use, the book can also be used for advanced undergraduate students planning for a career or further study in the subject area. The book will also better equip structural engineering consultants and practicing engineers in the use of standard software for seismic analysis of buildings, bridges, dams, and towers. Lecture materials for instructors available at www.wiley.com/go/dattaseismic
