Download or read book Safety and performance concept Reliability assessment of concrete structures written by fib Fédération internationale du béton and published by FIB - Féd. Int. du Béton. This book was released on 2018-08-01 with total page 375 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete structures have been built for more than 100 years. At first, reinforced concrete was used for buildings and bridges, even for those with large spans. Lack of methods for structural analysis led to conservative and reliable design. Application of prestressed concrete started in the 40s and strongly developed in the 60s. The spans of bridges and other structures like halls, industrial structures, stands, etc. grew significantly larger. At that time, the knowledge of material behaviour, durability and overall structural performance was substantially less developed than it is today. In many countries statically determined systems with a fragile behavior were designed for cast in situ as well as precast structures. Lack of redundancy resulted in a low level of robustness in structural systems. In addition, the technical level of individual technologies (e.g. grouting of prestressed cables) was lower than it is today. The number of concrete structures, including prestressed ones, is extremely high. Over time and with increased loading, the necessity of maintaining safety and performance parameters is impossible without careful maintenance, smaller interventions, strengthening and even larger reconstructions. Although some claim that unsatisfactory structures should be replaced by new ones, it is often impossible, as authorities, in general, have only limited resources. Most structures have to remain in service, probably even longer than initially expected. In order to keep the existing concrete structures in an acceptable condition, the development of methods for monitoring, inspection and assessment, structural identification, nonlinear analysis, life cycle evaluation and safety and prediction of the future behaviour, etc. is necessary. The scatter of individual input parameters must be considered as a whole. This requires probabilistic approaches to individual partial problems and to the overall analysis. The members of the fib Task Group 2.8 “Safety and performance concepts” wrote, on the basis of the actual knowledge and experience, a comprehensive document that provides crucial knowledge for existing structures, which is also applicable to new structures. This guide to good practice is divided into 10 basic chapters dealing with individual issues that are critical for activities associated with preferably existing concrete structures. Bulletin 86 starts with the specification of the performance-based requirements during the entire lifecycle. The risk issues are described in chapter two. An extensive part is devoted to structural reliability, including practical engineering approaches and reliability assessment of existing structures. Safety concepts for design consider the lifetime of structures and summarise safety formats from simple partial safety factors to develop approaches suitable for application in sophisticated, probabilistic, non-linear analyses. Testing for design and the determination of design values from the tests is an extremely important issue. This is especially true for the evaluation of existing structures. Inspection and monitoring of existing structures are essential for maintenance, for the prediction of remaining service life and for the planning of interventions. Chapter nine presents probabilistically-based models for material degradation processes. Finally, case studies are presented in chapter ten. The results of the concrete structures monitoring as well as their application for assessment and prediction of their future behaviour are shown. The risk analysis of highway bridges was based on extensive monitoring and numerical evaluation programs. Case studies perfectly illustrate the application of the methods presented in the Bulletin. The information provided in this guide is very useful for practitioners and scientists. It provides the reader with general procedures, from the specification of requirements, monitoring, assessment to the prediction of the structures’ lifecycles. However, one must have a sufficiently large amount of experimental and other data (e.g. construction experience) in order to use these methods correctly. This data finally allows for a statistical evaluation. As it is shown in case studies, extensive monitoring programs are necessary. The publication of this guide and other documents developed within the fib will hopefully help convince the authorities responsible for safe and fluent traffic on bridges and other structures that the costs spent in monitoring are first rather small, and second, they will repay in the form of a serious assessment providing necessary information for decision about maintenance and future of important structures.

Download or read book Safety Reliability Risk and Life Cycle Performance of Structures and Infrastructures written by George Deodatis and published by CRC Press. This book was released on 2014-02-10 with total page 1112 pages. Available in PDF, EPUB and Kindle. Book excerpt: Safety, Reliability, Risk and Life-Cycle Performance of Structures and Infrastructures contains the plenary lectures and papers presented at the 11th International Conference on STRUCTURAL SAFETY AND RELIABILITY (ICOSSAR2013, New York, NY, USA, 16-20 June 2013), and covers major aspects of safety, reliability, risk and life-cycle performance of str

Download or read book Introduction to Safety and Reliability of Structures written by Jörg Schneider and published by IABSE. This book was released on 2006 with total page 115 pages. Available in PDF, EPUB and Kindle. Book excerpt: Structural engineers devote all their effort to meeting society¿s expectations efficiently. Engineers and scientists work together to develop solutions to structural problems. Given that nothing is absolutely and eternally safe, the goal is to attain an acceptably small probability of failure for a structure. Reliability analysis is part of the science and practice of engineering today, not only with respect to the safety of structures, but also for questions of serviceability and other requirements of technical systems that might be impacted by some probability. The present volume takes a rather broad approach to the safety of structures and related topics. It treats the underlying concepts of risk and safety and introduces the reader to the main concepts and strategies for dealing with hazards. A chapter is devoted to the processing of data into information that is relevant for applying reliability theory. The two main chapters deal with the modelling of structures and with methods of reliability analysis. Another chapter focuses on problems related to establishing target reliabilities, assessing existing structures, and on effective strategies against human error. The Appendix supports the application of the methods proposed and refers readers to a number of related computer programs.

Download or read book Safety and performance concepts contributions to the workshop sessions model uncertainties new concepts and full scale testing written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 1993-08-01 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Reinforced Concrete Structural Reliability written by Mohamed Abdallah El-Reedy, Ph.D and published by CRC Press. This book was released on 2012-12-15 with total page 379 pages. Available in PDF, EPUB and Kindle. Book excerpt: Structural engineers must focus on a structure’s continued safety throughout its service life. Reinforced Concrete Structural Reliability covers the methods that enable engineers to keep structures reliable during all project phases, and presents a practical exploration of up-to-date techniques for predicting the lifetime of a structure. The book also helps readers understand where the safety factors used come from and addresses the problems that arise from deviation from these factors. It also examines the question of what code is best to follow for a specific project: the American code, the British Standard, the Eurocode, or other local codes. The author devotes an entire chapter to practical statistics methods and probability theory used in structural and civil engineering, both important for calculating the probability of structural failure (reliability analysis). The text addresses the effects of time, environmental conditions, and loads to assess consequences on older structures as well as to calculate the probability of failure. It also presents the effects of steel bar corrosion and column corrosion, and precautions to consider along with guides for design. This book offers guidelines and tools to evaluate existing as well as new structures, providing all available methods and tests for assessing structures, including visual inspection and nondestructive testing for concrete strength. It also presents techniques for predicting the remaining service life of a structure, which can be used to determine whether to perform repairs or take other action. This practical guide helps readers to differentiate between and understand the philosophy of the various codes and standards, enabling them to work anywhere in the world. It will aid engineers at all levels working on projects from the design to the maintenance phase, increasing their grasp of structure behavior, codes and factors, and predicting service life.

Download or read book Computational Structural Concrete written by Ulrich Haussler-Combe and published by John Wiley & Sons. This book was released on 2022-11-21 with total page 450 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete is by far the most used building material due to its advantages: it is shapeable, cost-effective and available everywhere. Combined with reinforcement it provides an immense bandwidth of properties and may be customized for a huge range of purposes. Thus, concrete is the building material of the 20th century. To be the building material of the 21th century its sustainability has to move into focus. Reinforced concrete structures have to be designed expending less material whereby their load carrying potential has to be fully utilized. Computational methods such as Finite Element Method (FEM) provide essential tools to reach the goal. In combination with experimental validation, they enable a deeper understanding of load carrying mechanisms. A more realistic estimation of ultimate and serviceability limit states can be reached compared to traditional approaches. This allows for a significantly improved utilization of construction materials and a broader horizon for innovative structural designs opens up. However, sophisticated computational methods are usually provided as black boxes. Data is fed in, the output is accepted as it is, but an understanding of the steps in between is often rudimentary. This has the risk of misinterpretations, not to say invalid results compared to initial problem definitions. The risk is in particular high for nonlinear problems. As a composite material, reinforced concrete exhibits nonlinear behaviour in its limit states, caused by interaction of concrete and reinforcement via bond and the nonlinear properties of the components. Its cracking is a regular behaviour. The book aims to make the mechanisms of reinforced concrete transparent from the perspective of numerical methods. In this way, black boxes should also become transparent. Appropriate methods are described for beams, plates, slabs and shells regarding quasi-statics and dynamics. Concrete creeping, temperature effects, prestressing, large displacements are treated as examples. State of the art concrete material models are presented. Both the opportunities and the pitfalls of numerical methods are shown. Theory is illustrated by a variety of examples. Most of them are performed with the ConFem software package implemented in Python and available under open-source conditions.

Download or read book Reliability Basis of Load and Resistance Factors for Reinforced Concrete Design written by Bruce R. Ellingwood and published by . This book was released on 1978 with total page 108 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Partial factor methods for existing concrete structures written by FIB - Féd. Int. du Béton and published by FIB - Féd. Int. du Béton. This book was released on 2016 with total page 145 pages. Available in PDF, EPUB and Kindle. Book excerpt: For a large part of the existing buildings and infrastructure the design life has been reached or will be reached in the near future. These structures might need to be reassessed in order to investigate whether the safety requirements are met. Current practice on the assessment of existing concrete structures however needs a thorough evaluation from a risk and reliability point of view, as they are mostly verified using simplified procedures based on the partial factor method commonly applied in design of new structures. Such assessments are often conservative and may lead to expensive upgrades. Although the last decades reliability-based assessment of existing concrete structures has gained wide attention in the research field, a consistent reliability-based assessment framework and a practically applicable codified approach which is compatible with the Eurocodes and accessible for common structural engineering problems in everyday practice is currently missing. Such an approach however allows for a more uniform, more objective and probably more widely applied assessment approach for existing concrete structures. Hence, in this bulletin two different partial factor formats are elaborated, i.e. the Design Value Method (DVM) and the Adjusted Partial Factor Method (APFM), enabling the incorporation of specific reliability related aspects for existing structures. The DVM proposes a fundamental basis for evaluating partial factors whereas the APFM provides adjustment factors to be applied on the partial factors for new structures in EN 1990. In this bulletin both methods are elaborated and evaluated and a basis is provided for decision making regarding the target safety level of existing structures.

Download or read book Monitoring and Safety Evaluation of Existing Concrete Structures written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2003 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt: The condition assessment of aged structures is becoming a more and more important issue for civil infrastructure management systems. The continued use of existing systems is, due to environmental, economical and socio-political assets, of great significance and is growing larger every year. Thus the extent of necessary repair of damaged reinforced concrete structures is of major concern in most countries today. Monitoring techniques may have a decisive input to limit expenditures for maintenance and repair of existing structures. Modern test and measurement methods as well as computational mechanics open the door for a wide variety of monitoring applications. The need for quantitative and qualitative knowledge has led to the development and improvement of surveillance techniques, which have already found successful application in other disciplines such as medicine, physics and chemistry. The design of experimental test and measurement systems is inherently an interdisciplinary activity. The specification of the instrumentation to measure the structural response will involve the skills of civil, electrical and computer engineers. The main aim of fib Commission 5, Structural servicer life aspects, is to provide a rational procedure to obtain an optimal technical-economic performance of concrete structures in service and to ensure a feedback of experience gained to design, execution, maintenance and rehabilitation. Against this background fib Task Group 5.1 Monitoring and Safety Evaluation of Existing Concrete Structures had been established to evaluate the existing practice worldwide. The objective of this state-of-art report is to summarize the most important inspection and measuring methods, to describe the working process and to evaluate the applicability to structural monitoring. Particular emphasis is placed upon non-destructive systems, lifetime monitoring, data evaluation and safety aspects.

Download or read book Guidelines for the Design and Assessment of Concrete Structures Subjected to Impact written by P. Barr and published by . This book was released on 1988 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Proceedings fib Symposium in Stuttgart written by FIB – International Federation for Structural Concrete and published by FIB - Féd. Int. du Béton. This book was released on 2008-09-01 with total page 1168 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Non Destructive Assessment of Concrete Structures Reliability and Limits of Single and Combined Techniques written by Denys Breysse and published by Springer Science & Business Media. This book was released on 2012-01-21 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives information on non destructive techniques for assessment of concrete structures. It synthesizes the best of international knowledge about what techniques can be used for assessing material properties (strength) and structural properties (geometry, defects...). It describes how the techniques can be used so as to answer a series of usual questions, highlighting their capabilities and limits, and providing advices for a better use of techniques. It also focuses on possible combinations of techniques so as to improve the assessment. It is based on many illustrative examples and give in each case references to standards and guidelines.

Download or read book fib Model Code for Concrete Structures 2010 written by fib - federation internationale du beton and published by John Wiley & Sons. This book was released on 2013-12-04 with total page 434 pages. Available in PDF, EPUB and Kindle. Book excerpt: The International Federation for Structural Concrete (fib) is a pre-normative organization. 'Pre-normative' implies pioneering work in codification. This work has now been realized with the fib Model Code 2010. The objectives of the fib Model Code 2010 are to serve as a basis for future codes for concrete structures, and present new developments with regard to concrete structures, structural materials and new ideas in order to achieve optimum behaviour. The fib Model Code 2010 is now the most comprehensive code on concrete structures, including their complete life cycle: conceptual design, dimensioning, construction, conservation and dismantlement. It is expected to become an important document for both national and international code committees, practitioners and researchers. The fib Model Code 2010 was produced during the last ten years through an exceptional effort by Joost Walraven (Convener; Delft University of Technology, The Netherlands), Agnieszka Bigaj-van Vliet (Technical Secretary; TNO Built Environment and Geosciences, The Netherlands) as well as experts out of 44 countries from five continents.

Download or read book Durability Design of Concrete Structures written by A. Sarja and published by CRC Press. This book was released on 2004-03-01 with total page 93 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete structures can be designed for durability by applying the principles and procedures of reliability theory combined with traditional structural design. This book is the first systematic attempt to introduce into structural design a general theory of structural reliability and existing calculation models for common degradation processes. It covers both the theoretical background and practical design for service life and includes worked examples which highlight the application of the design procedure and methods.

Download or read book Structural Concrete Textbook Volume 5 written by fib Fédération internationale du béton and published by fib Fédération internationale du béton. This book was released on 2012-06-01 with total page 482 pages. Available in PDF, EPUB and Kindle. Book excerpt: The third edition of the Structural Concrete Textbook is an extensive revision that reflects advances in knowledge and technology over the past decade. It was prepared in the intermediate period from the CEP-FIP Model Code 1990 (MC90) tofib Model Code for Concrete Structures 2010 (MC2010), and as such incorporates a significant amount of information that has been already finalized for MC2010, while keeping some material from MC90 that was not yet modified considerably. The objective of the textbook is to give detailed information on a wide range of concrete engineering from selection of appropriate structural system and also materials, through design and execution and finally behaviour in use. The revised fib Structural Concrete Textbook covers the following main topics: phases of design process, conceptual design, short and long term properties of conventional concrete (including creep, shrinkage, fatigue and temperature influences), special types of concretes (such as self compacting concrete, architectural concrete, fibre reinforced concrete, high and ultra high performance concrete), properties of reinforcing and prestressing materials, bond, tension stiffening, moment-curvature, confining effect, dowel action, aggregate interlock; structural analysis (with or without time dependent effects), definition of limit states, control of cracking and deformations, design for moment, shear or torsion, buckling, fatigue, anchorages, splices, detailing; design for durability (including service life design aspects, deterioration mechanisms, modelling of deterioration mechanisms, environmental influences, influences of design and execution on durability); fire design (including changes in material and structural properties, spalling, degree of deterioration), member design (linear members and slabs with reinforcement layout, deep beams); management, assessment, maintenance, repair (including, conservation strategies, risk management, types of interventions) as well as aspects of execution (quality assurance), formwork and curing. The updated textbook provides the basics of material and structural behaviour and the fundamental knowledge needed for the design, assessment or retrofitting of concrete structures. It will be essential reading material for graduate students in the field of structural concrete, and also assist designers and consultants in understanding the background to the rules they apply in their practice. Furthermore, it should prove particularly valuable to users of the new editions of Eurocode 2 for concrete buildings, bridges and container structures, which are based only partly on MC90 and partly on more recent knowledge which was not included in the 1999 edition of the textbook.

Download or read book A guide to the comite euro international du b ton mission working programmes membership directory written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 1996-03-01 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Civil and Environmental Engineering Concepts Methodologies Tools and Applications written by Management Association, Information Resources and published by IGI Global. This book was released on 2016-01-31 with total page 1670 pages. Available in PDF, EPUB and Kindle. Book excerpt: Civil and environmental engineers work together to develop, build, and maintain the man-made and natural environments that make up the infrastructures and ecosystems in which we live and thrive. Civil and Environmental Engineering: Concepts, Methodologies, Tools, and Applications is a comprehensive multi-volume publication showcasing the best research on topics pertaining to road design, building maintenance and construction, transportation, earthquake engineering, waste and pollution management, and water resources management and engineering. Through its broad and extensive coverage on a variety of crucial concepts in the field of civil engineering, and its subfield of environmental engineering, this multi-volume work is an essential addition to the library collections of academic and government institutions and appropriately meets the research needs of engineers, environmental specialists, researchers, and graduate-level students.