Download or read book Robust Model Predictive Control and Scheduling Co design for Networked Cyber physical Systems written by Changxin Liu and published by . This book was released on 2019 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In modern cyber-physical systems (CPSs) where the control signals are generally transmitted via shared communication networks, there is a desire to balance the closed-loop control performance with the communication cost necessary to achieve it. In this context, aperiodic real-time scheduling of control tasks comes into being and has received increasing attention recently. It is well known that model predictive control (MPC) is currently widely utilized in industrial control systems and has greatly increased profits in comparison with the proportional integral-derivative (PID) control. As communication and networks play more and more important roles in modern society, there is a great trend to upgrade and transform traditional industrial systems into CPSs, which naturally requires extending conventional MPC to communication-efficient MPC to save network resources. Motivated by this fact, we in this thesis propose robust MPC and scheduling co-design algorithms to networked CPSs possibly affected by both parameter uncertainties and additive disturbances. In Chapter 2, a dynamic event-triggered robust tube-based MPC for constrained linear systems with additive disturbances is developed, where a time-varying pre-stabilizing gain is obtained by interpolating multiple static state feedbacks and the interpolating coefficient is determined via optimization at the time instants when the MPC-based control is triggered. The original constraints are properly tightened to achieve robust constraint optimization and a sequence of dynamic sets used to test events are derived according to the optimized coefficient. We theoretically show that the proposed algorithm is recursively feasible and the closed-loop system is input-to-state stable (ISS) in the attraction region. Numerical results are presented to verify the design. In Chapter 3, a self-triggered min-max MPC strategy is developed for constrained nonlinear systems subject to both parametric uncertainties and additive disturbances, where the robust constraint satisfaction is achieved by considering the worst case of all possible uncertainty realizations. First, we propose a new cost function that relaxes the penalty on the system state in a time period where the controller will not be invoked. With this cost function, the next triggering time instant can be obtained at current time instant by solving a min-max optimization problem where the maximum triggering period becomes a decision variable. The proposed strategy is proved to be input-to-state practical stable (ISpS) in the attraction region at triggering time instants under some standard assumptions. Extensions are made to linear systems with additive disturbances, for which the conditions reduce to a linear matrix inequality (LMI). Comprehensive numerical experiments are performed to verify the correctness of the theoretical results.
Download or read book Robust Model Predictive Control of Resilient Cyber physical Systems written by Qi Sun and published by . This book was released on 2021 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Cyber-physical systems (CPS), integrating advanced computation, communication, and control technologies with the physical process, are widely applied in industry applications such as smart production and manufacturing systems, robotic and automotive control systems, and smart grids. Due to possible exposure to unreliable networks and complex physical environments, CPSs may simultaneously face multiple cyber and physical issues including cyber threats (e.g., malicious cyber attacks) and resource constraints (e.g., limited networking resources and physical constraints). As one of the essential topics in designing efficient CPSs, the controller design for CPSs, aiming to achieve secure and resource-aware control objectives under such cyber and physical issues, is very significant yet challenging. Emphasizing optimality and system constraint handling, model predictive control (MPC) is one of the most widely used control paradigms, notably famous for its successful applications in chemical process industry. However, the conventional MPC methods are not specifically tailored to tackle cyber threats and resource constraints, thus the corresponding theory and tools to design the secure and resource-aware controller are lacking and need to be developed. This dissertation focuses on developing MPC-based methodologies to address the i) secure control problem and ii) resource-aware control problem for CPSs subject to cyber threats and resource constraints. In the resource-aware control problem of CPSs, the nonlinear system with additive disturbance is considered. By using an integral-type event-triggered mechanism and an improved robustness constraint, we propose an integral-type event-triggered MPC so that smaller sampling frequency and robustness to the additive disturbance can be obtained. The sufficient conditions for guaranteeing the recursive feasibility and the closed-loop stability are established. For the secure control problem of CPSs, two aspects are considered. Firstly, to achieve the secure control objective, we design a secure dual-mode MPC framework, including a modified initial feasible set and a new positively invariant set, for constrained linear systems subject to Denial-of-Service (DoS) attacks. The exponential stability of the closed-loop system is guaranteed under several conditions. Secondly, to deal with cyber threats and take advantage of the cloud-edge computing technology, we propose a model predictive control as a secure service (MPCaaSS) framework, consisting of a double-layer controller architecture and a secure data transmission protocol, for constrained linear systems in the presence of both cyber threats and external disturbances. The rigorous recursive feasibility and robust stability conditions are established. To simultaneously address the secure and resource-aware control problems, an event-triggered robust nonlinear MPC framework is proposed, where a new robustness constraint is introduced to deal with additive disturbances, and a packet transmission strategy is designed to tackle DoS attacks. Then, an event-triggered mechanism, which accommodates DoS attacks occurring in the communication network, is proposed to reduce the communication cost for resource-constrained CPSs. The recursive feasibility and the closed-loop stability in the sense of input-to-state practical stable (ISpS) are guaranteed under the established sufficient conditions.
Download or read book Networked and Event Triggered Control Approaches in Cyber Physical Systems written by Jinhui Zhang and published by CRC Press. This book was released on 2022-01-27 with total page 221 pages. Available in PDF, EPUB and Kindle. Book excerpt: The insertion of communication networks in feedback control loops complicates analysis and synthesis of cyber-physical systems (CPSs), and network-induced uncertainties may degrade system control performance. Thus, this book researches networked delay compensation and event-triggered control approaches for a series of CPSs subject to network-induced uncertainties. The authors begin with an introduction to the concepts and challenges of CPSs, followed by an overview of networked control approaches and event-triggered control strategies in CPSs. Then, networked delay compensation and event-triggered control approaches are proposed for CPSs with network communication delay, data dropout, signal quantization, and event-triggered communication. More specifically, networked delay compensation approaches are proposed for linear/nonlinear networked controlled plants with time-varying and random network communication delays and data dropouts. To reduce computational burden and network communication loads in CPSs, event-triggered control, self-triggered control, co-design of event-triggered control and quantized control techniques, and event-triggered disturbance rejection control approaches are also presented. This book is an essential text for researchers and engineers interested in cybersecurity, networked control, and CPSs. It would also prove useful for graduate students in the fields of science, engineering, and computer science.
Download or read book Control and Communiction Schedule Co design for Networked Control Systems written by Masoud Bahraini and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Optimal and Robust Scheduling for Networked Control Systems written by Stefano Longo and published by CRC Press. This book was released on 2018-09-03 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: Optimal and Robust Scheduling for Networked Control Systems tackles the problem of integrating system components—controllers, sensors, and actuators—in a networked control system. It is common practice in industry to solve such problems heuristically, because the few theoretical results available are not comprehensive and cannot be readily applied by practitioners. This book offers a solution to the deterministic scheduling problem that is based on rigorous control theoretical tools but also addresses practical implementation issues. Helping to bridge the gap between control theory and computer science, it suggests that the consideration of communication constraints at the design stage will significantly improve the performance of the control system. Technical Results, Design Techniques, and Practical Applications The book brings together well-known measures for robust performance as well as fast stochastic algorithms to assist designers in selecting the best network configuration and guaranteeing the speed of offline optimization. The authors propose a unifying framework for modelling NCSs with time-triggered communication and present technical results. They also introduce design techniques, including for the codesign of a controller and communication sequence and for the robust design of a communication sequence for a given controller. Case studies explore the use of the FlexRay TDMA and time-triggered control area network (CAN) protocols in an automotive control system. Practical Solutions to Your Time-Triggered Communication Problems This unique book develops ready-to-use engineering tools for large-scale control system integration with a focus on robustness and performance. It emphasizes techniques that are directly applicable to time-triggered communication problems in the automotive industry and in avionics, robotics, and automated manufacturing.
Download or read book Networked Predictive Control of Systems with Communication Constraints and Cyber Attacks written by Zhong-Hua Pang and published by Springer. This book was released on 2018-12-23 with total page 219 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the latest results on predictive control of networked systems, where communication constraints (e.g., network-induced delays and packet dropouts) and cyber attacks (e.g., deception attacks and denial-of-service attacks) are considered. For the former, it proposes several networked predictive control (NPC) methods based on input-output models and state-space models respectively. For the latter, it designs secure NPC schemes from the perspectives of information security and real-time control. Furthermore, it uses practical experiments to demonstrate the effectiveness and applicability of all the methods, bridging the gap between control theory and practical applications. The book is of interest to academic researchers, R&D engineers, and graduate students in control engineering, networked control systems and cyber-physical systems.
Download or read book Networked Control Systems written by Alberto Bemporad and published by Springer. This book was released on 2010-10-15 with total page 373 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book nds its origin in the WIDE PhD School on Networked Control Systems, which we organized in July 2009 in Siena, Italy. Having gathered experts on all the aspects of networked control systems, it was a small step to go from the summer school to the book, certainly given the enthusiasm of the lecturers at the school. We felt that a book collecting overviewson the important developmentsand open pr- lems in the eld of networked control systems could stimulate and support future research in this appealing area. Given the tremendouscurrentinterests in distributed control exploiting wired and wireless communication networks, the time seemed to be right for the book that lies now in front of you. The goal of the book is to set out the core techniques and tools that are ava- able for the modeling, analysis and design of networked control systems. Roughly speaking, the book consists of three parts. The rst part presents architectures for distributed control systems and models of wired and wireless communication n- works. In particular, in the rst chapter important technological and architectural aspects on distributed control systems are discussed. The second chapter provides insight in the behavior of communication channels in terms of delays, packet loss and information constraints leading to suitable modeling paradigms for commu- cation networks.
Download or read book Networked and Distributed Predictive Control written by Panagiotis D. Christofides and published by Springer Science & Business Media. This book was released on 2011-04-07 with total page 253 pages. Available in PDF, EPUB and Kindle. Book excerpt: Networked and Distributed Predictive Control presents rigorous, yet practical, methods for the design of networked and distributed predictive control systems – the first book to do so. The design of model predictive control systems using Lyapunov-based techniques accounting for the influence of asynchronous and delayed measurements is followed by a treatment of networked control architecture development. This shows how networked control can augment dedicated control systems in a natural way and takes advantage of additional, potentially asynchronous and delayed measurements to maintain closed loop stability and significantly to improve closed-loop performance. The text then shifts focus to the design of distributed predictive control systems that cooperate efficiently in computing optimal manipulated input trajectories that achieve desired stability, performance and robustness specifications but spend a fraction of the time required by centralized control systems. Key features of this book include: • new techniques for networked and distributed control system design; • insight into issues associated with networked and distributed predictive control and their solution; • detailed appraisal of industrial relevance using computer simulation of nonlinear chemical process networks and wind- and solar-energy-generation systems; and • integrated exposition of novel research topics and rich resource of references to significant recent work. A full understanding of Networked and Distributed Predictive Control requires a basic knowledge of differential equations, linear and nonlinear control theory and optimization methods and the book is intended for academic researchers and graduate students studying control and for process control engineers. The constant attention to practical matters associated with implementation of the theory discussed will help each of these groups understand the application of the book’s methods in greater depth.
Download or read book Co design Approaches to Dependable Networked Control Systems written by Daniel Simon and published by John Wiley & Sons. This book was released on 2013-03-04 with total page 261 pages. Available in PDF, EPUB and Kindle. Book excerpt: Networked Control Systems (NCS) is a growing field of application and calls for the development of integrated approaches requiring multidisciplinary skills in control, real-time computing and communication protocols. This book describes co-design approaches, and establishes the links between the QoC (Quality of Control) and QoS (Quality of Service) of the network and computing resources. The methods and tools described in this book take into account, at design level, various parameters and properties that must be satisfied by systems controlled through a network. Among the important network properties examined are the QoC, the dependability of the system, and the feasibility of the real-time scheduling of tasks and messages. Correct exploitation of these approaches allows for efficient design, diagnosis, and implementation of the NCS. This book will be of great interest to researchers and advanced students in automatic control, real-time computing, and networking domains, and to engineers tasked with development of NCS, as well as those working in related network design and engineering fields.
Download or read book Investigation on Robust Codesign Methods for Networked Control Systems written by Sanad Al-Areqi and published by Logos Verlag Berlin GmbH. This book was released on 2015-12-31 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: The problem of jointly designing a robust controller and an intelligent scheduler for networked control systems (NCSs) is addressed in this thesis. NCSs composing of multiple plants that share a single channel communication network with uncertain time-varying transmission times are modeled as switched polytopic systems with additive norm-bounded uncertainty. Switching is deployed to represent scheduling, the polytopic uncertainty to overapproximatively describe the uncertain time-varying transmission times. Based on the resulting NCS model and a state feedback control law, the control and scheduling codesign problem is then introduced and formulated as a robust (minimax) optimization problem with the objective of minimizing the worst-case value of an associated infinite time-horizon quadratic cost function. Five robust codesign strategies are investigated for tackling the introduced optimization problem, namely: Periodic control and scheduling (PCS), Receding-horizon control and scheduling (RHCS), Implementation-aware control and scheduling (IACS), Event-based control and scheduling (EBCS), Prediction-based control and scheduling (PBCS). All these codesign strategies are determined from LMI optimization problems based on the Lyapunov theory. The properties of each are evaluated and compared in terms of computational complexity and control performance based on simulation and experimental study, showing their effectiveness in improving the performance while utilizing the limited communication resources very efficiently.
Download or read book Packet Based Control for Networked Control Systems written by Yun-Bo Zhao and published by Springer. This book was released on 2017-09-14 with total page 186 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces a unique, packet-based co-design control framework for networked control systems. It begins by providing a comprehensive survey of state-of-the-art research on networked control systems, giving readers a general overview of the field. It then verifies the proposed control framework both theoretically and experimentally – the former using multiple control methodologies, and the latter using a unique online test rig for networked control systems. The framework investigates in detail the most common, communication constraints, including network-induced delays, data packet dropout, data packet disorders, and network access constraints, as well as multiple controller design and system analysis tools such as model predictive control, linear matrix inequalities and optimal control. This unique and complete co-design framework greatly benefits researchers, graduate students and engineers in the fields of control theory and engineering.
Download or read book Control Strategies and Co Design of Networked Control Systems written by Héctor Benítez-Pérez and published by Springer. This book was released on 2018-07-31 with total page 193 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents Networked Control System (NCS) as a particular kind of a real-time distributed system (RTDS), composed of a set of nodes, interconnected by a network, and able to develop a complete control process. It describes important parts of the control process such as sensor and actuator activities, which rely on a real-time operating system, and a real-time communication network. As the use of common bus network architecture introduces different forms of uncertainties between sensors, actuators, and controllers, several approaches such as reconfigurable systems have been developed to tackle this problem. Moreover, modeling NCS is a challenging procedure, since there are several non-linear situations, like local saturations, uncertain time delays, dead-zones, or local situations, it is necessary to deal with. The book describes a novel strategy for modelling and control based on a fuzzy control approach and codesign strategies.
Download or read book Multi Sensor Filtering Fusion with Censored Data Under a Constrained Network Environment written by Hang Geng and published by CRC Press. This book was released on 2024-08-26 with total page 263 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the up-to-date research developments and novel methodologies on multi-sensor filtering fusion (MSFF) for a class of complex systems subject to censored data under a constrained network environment. The contents of this book are divided into two parts covering centralized and distributed MSFF design methodologies. The work provides a framework of optimal centralized/distributed filter design and stability and performance analysis for the considered systems along with designed filters. Simulations presented in this book are implemented using MATLAB. Features: Includes concepts, backgrounds and models on censored data, filtering fusion and communication constraints. Reviews case studies to provide clear engineering insights into the developed fusion theories and techniques. Provides theoretic values and engineering insights of the censored data and constrained network. Discusses performance evaluation of the presented multi-sensor fusion algorithms. Explores promising research directions on future multi-sensor fusion. This book is aimed at graduate students and researchers in networked control, sensor networks, and data fusion.
Download or read book Packet Based Control for Networked Control Systems written by Yun-Bo Zhao and published by Springer. This book was released on 2017-09-28 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces a unique, packet-based co-design control framework for networked control systems. It begins by providing a comprehensive survey of state-of-the-art research on networked control systems, giving readers a general overview of the field. It then verifies the proposed control framework both theoretically and experimentally – the former using multiple control methodologies, and the latter using a unique online test rig for networked control systems. The framework investigates in detail the most common, communication constraints, including network-induced delays, data packet dropout, data packet disorders, and network access constraints, as well as multiple controller design and system analysis tools such as model predictive control, linear matrix inequalities and optimal control. This unique and complete co-design framework greatly benefits researchers, graduate students and engineers in the fields of control theory and engineering.
Download or read book Tracking Control of Networked Systems via Sliding Mode written by Meng Li and published by Springer Nature. This book was released on 2021-10-29 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book focuses on the research methods of networked control systems via sliding mode. The problems with network disturbances, network induced delay, out-of-sequence and packet loss, and network attacks are studied in detail. The content studied in this book is introduced in detail and is verified by simulation or experiment. It is especially suitable for readers who are interested in learning the control scheme of networked systems. This book can benefit researchers, engineers, and students in related fields such as electrical, control, automation, and cyber security.
Download or read book Optimal and Robust Scheduling for Networked Control Systems written by Stefano Longo and published by . This book was released on 2011 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Economic Model Predictive Control written by Helen Durand and published by Foundations and Trends (R) in Systems and Control. This book was released on 2018-06-19 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: Economic Model Predictive Control (EMPC) is a control strategy that moves process operation away from the steady-state paradigm toward a potentially time-varying operating strategy to improve process profitability. The EMPC literature is replete with evidence that this new paradigm may enhance process profits when a model of the chemical process provides a sufficiently accurate representation of the process dynamics. Systems using EMPC often neglect the dynamics associated with equipment and are often neglected when modeling a chemical process. Recent studies have shown they can significantly impact the effectiveness of an EMPC system. Concentrating on valve behavior in a chemical process, this monograph develops insights into the manner in which equipment behavior should impact the design process for EMPC and to provide a perspective on a number of open research topics in this direction. Written in tutorial style, this monograph provides the reader with a full literature review of the topic and demonstrates how these techniques can be adopted in a practical system.
