Download or read book Residual Stress Effects in Fatigue written by H. S. Reemsnyder and published by ASTM International. This book was released on 1982 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Analytical and Experimental Methods for Residual Stress Effects in Fatigue written by Robert L. Champoux and published by ASTM International. This book was released on 1988 with total page 141 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Residual Stress Effects in Fatigue written by and published by . This book was released on 1982 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Residual Stress Effects in Fatigue written by and published by . This book was released on with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Residual Stress and Stress Relaxation written by Eric Kula and published by Springer Science & Business Media. This book was released on 2013-11-21 with total page 529 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Army Materials and Mechanics Research Center in coop eration with the Materials Science Group of the Department of Chemical Engineering and Materials Science of Syracuse University has been conducting the Annual Sagamore Army Materials Research Conference since 1954. The specific purpose of these conferences has been to bring together scientists and engineers from academic institutions, industry and government who are uniquely qualified to explore in depth a subject of importance to the Department of Defense, the Army and the scientific community. These proceedings, entitled RESIDUAL STRESS AND STRESS RELAXATION, address the nature of residual stresses and their measurements, the sources of residual stress, stress relaxation, sub-critical crack growth in the presence of residual stress, residual stresses and properties, and research in progress. We wish to acknowledge the assistance of Mr. Dan McNaught of the Army Materials and Mechanics Research Center and Mr. Robert J. Sell and Helen Brown DeMascio of Syracuse University throughout the stages of the conference planning and finally the publication of the book. The continued active interest and support of these conferences by Dr. E. Wright, Director of the Army Materials and Mechanics Research Center, is appreciated.
Download or read book Fatigue of Structures and Materials written by J. Schijve and published by Springer Science & Business Media. This book was released on 2008-12-16 with total page 627 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue of structures and materials covers a wide scope of different topics. The purpose of the present book is to explain these topics, to indicate how they can be analyzed, and how this can contribute to the designing of fatigue resistant structures and to prevent structural fatigue problems in service. Chapter 1 gives a general survey of the topic with brief comments on the signi?cance of the aspects involved. This serves as a kind of a program for the following chapters. The central issues in this book are predictions of fatigue properties and designing against fatigue. These objectives cannot be realized without a physical and mechanical understanding of all relevant conditions. In Chapter 2 the book starts with basic concepts of what happens in the material of a structure under cyclic loads. It illustrates the large number of variables which can affect fatigue properties and it provides the essential background knowledge for subsequent chapters. Different subjects are presented in the following main parts: • Basic chapters on fatigue properties and predictions (Chapters 2–8) • Load spectra and fatigue under variable-amplitude loading (Chapters 9–11) • Fatigue tests and scatter (Chapters 12 and 13) • Special fatigue conditions (Chapters 14–17) • Fatigue of joints and structures (Chapters 18–20) • Fiber-metal laminates (Chapter 21) Each chapter presents a discussion of a speci?c subject.
Download or read book Residual Stress Effects on Fatigue and Fracture Testing and Incorporation of Results Into Design written by Michael R. Mitchell and published by ASTM International. This book was released on 2007 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Eleven peer-reviewed papers, written by experts in their field, provide an understanding of residual stresses, fatigue crack growth, fatigue lifetime predictions, and their effect on structural integrity. Residual stresses can be present due to processing and manufacturing of materials and structures, so it is imperative to understand how and why they can influence the test data that we used in structural design methodologies. Residual stresses may also be intentionally engineered into structures in attempts to improve fatigue life, and it is equally important that designers understand how to account for these potential effects on fatigue life."--Publisher's website.
Download or read book Heat Effects of Welding written by Dieter Radaj and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: Almost all welding technology depends upon the use of concentrated energy sources to fuse or soften the material locally at the joint, before such energy can be diffused or dispersed elsewhere. Although comprehensive treatments of transient heat flow as a controlling influence have been developed progressively and published over the past forty years, the task of uniting the results compactly within a textbook has become increasingly formidable. With the comparative scarcity of such works, welding engineers have been denied the full use of powerful design analysis tools. During the past decade Dr Radaj has prepared to fulfil this need, working from a rich experience as pioneer researcher and teacher, co-operator with Professor Argyris at Stuttgart University in developing the finite element method for stress analysis of aircraft and power plant structures, and more recently as expert consultant on these and automotive structures at Daimler Benz. His book appeared in 1988 in the German language, and this updated English language edition will significantly increase the availability of the work.
Download or read book Springer Handbook of Experimental Solid Mechanics written by William N. Sharpe, Jr. and published by Springer Science & Business Media. This book was released on 2008-12-04 with total page 1100 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Springer Handbook of Experimental Solid Mechanics documents both the traditional techniques as well as the new methods for experimental studies of materials, components, and structures. The emergence of new materials and new disciplines, together with the escalating use of on- and off-line computers for rapid data processing and the combined use of experimental and numerical techniques have greatly expanded the capabilities of experimental mechanics. New exciting topics are included on biological materials, MEMS and NEMS, nanoindentation, digital photomechanics, photoacoustic characterization, and atomic force microscopy in experimental solid mechanics. Presenting complete instructions to various areas of experimental solid mechanics, guidance to detailed expositions in important references, and a description of state-of-the-art applications in important technical areas, this thoroughly revised and updated edition is an excellent reference to a widespread academic, industrial, and professional engineering audience.
Download or read book Practical Residual Stress Measurement Methods written by Gary S. Schajer and published by John Wiley & Sons. This book was released on 2013-09-23 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt: An introductory and intermediate level handbook written in pragmatic style to explain residual stresses and to provide straightforward guidance about practical measurement methods. Residual stresses play major roles in engineering structures, with highly beneficial effects when designed well, and catastrophic effects when ignored. With ever-increasing concern for product performance and reliability, there is an urgent need for a renewed assessment of traditional and modern measurement techniques. Success critically depends on being able to make the most practical and effective choice of measurement method for a given application. Practical Residual Stress Measurement Methods provides the reader with the information needed to understand key residual stress concepts and to make informed technical decisions about optimal choice of measurement technique. Each chapter, written by invited specialists, follows a focused and pragmatic format, with subsections describing the measurement principle, residual stress evaluation, practical measurement procedures, example applications, references and further reading. The chapter authors represent both international academia and industry. Each of them brings to their writing substantial hands-on experience and expertise in their chosen field. Fully illustrated throughout, the book provides a much-needed practical approach to residual stress measurements. The material presented is essential reading for industrial practitioners, academic researchers and interested students. Key features: • Presents an overview of the principal residual stress measurement methods, both destructive and non-destructive, with coverage of new techniques and modern enhancements of established techniques • Includes stand-alone chapters, each with its own figures, tables and list of references, and written by an invited team of international specialists
Download or read book Fracture and Fatigue of Welded Joints and Structures written by K Macdonald and published by Elsevier. This book was released on 2011-04-19 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: The failure of any welded joint is at best inconvenient and at worst can lead to catastrophic accidents. Fracture and fatigue of welded joints and structures analyses the processes and causes of fracture and fatigue, focusing on how the failure of welded joints and structures can be predicted and minimised in the design process. Part one concentrates on analysing fracture of welded joints and structures, with chapters on constraint-based fracture mechanics for predicting joint failure, fracture assessment methods and the use of fracture mechanics in the fatigue analysis of welded joints. In part two, the emphasis shifts to fatigue, and chapters focus on a variety of aspects of fatigue analysis including assessment of local stresses in welded joints, fatigue design rules for welded structures, k-nodes for offshore structures and modelling residual stresses in predicting the service life of structures. With its distinguished editor and international team of contributors, Fracture and fatigue of welded joints and structures is an essential reference for mechanical, structural and welding engineers, as well as those in the academic sector with a research interest in the field. Analyses the processes and causes of fracture and fatigue, focusing predicting and minimising the failure of welded joints in the design process Assesses the fracture of welded joints and structure featuring constraint-based fracture mechanics for predicting joint failure Explores specific considerations in fatigue analysis including the assessment of local stresses in welded joints and fatigue design rules for welded structures
Download or read book Recommendations for Fatigue Design of Welded Joints and Components written by A. F. Hobbacher and published by Springer. This book was released on 2015-12-23 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a basis for the design and analysis of welded components that are subjected to fluctuating forces, to avoid failure by fatigue. It is also a valuable resource for those on boards or commissions who are establishing fatigue design codes. For maximum benefit, readers should already have a working knowledge of the basics of fatigue and fracture mechanics. The purpose of designing a structure taking into consideration the limit state for fatigue damage is to ensure that the performance is satisfactory during the design life and that the survival probability is acceptable. The latter is achieved by the use of appropriate partial safety factors. This document has been prepared as the result of an initiative by Commissions XIII and XV of the International Institute of Welding (IIW).
Download or read book Fatigue Design of Welded Joints and Components written by A Hobbacher and published by Woodhead Publishing. This book was released on 1996-10-31 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: These recommendations present general methods for the assessment of fatigue damage in welded components, which may affect the limit states of a structure, such as ultimate limit state and serviceability limited state. Fatigue resistance data is given for welded components made of wrought or extruded products of ferritic/pearlitic or banitic structural steels up to fy = 700 Mpa and of aluminium alloys commonly used for welded structures.
Download or read book Welding Residual Stresses and Distortion written by Dieter Radaj and published by . This book was released on 2003 with total page 397 pages. Available in PDF, EPUB and Kindle. Book excerpt: This title deals with the computational simulation of temperature fields, residual stresses and distortion occuring during and after welding. Computational simulation is understood to be the reduction of the typical welding phenomena just mentionaed to physical models, and their mathematical representation in the form of computer programs.
Download or read book IIW Recommendations On Methods for Improving the Fatigue Strength of Welded Joints written by P J Haagensen and published by Woodhead Publishing. This book was released on 2013-01-25 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt: The weld toe is a primary source of fatigue cracking because of the severity of the stress concentration it produces. Weld toe improvement can increase the fatigue strength of new structures significantly. It can also be used to repair or upgrade existing structures. However, in practice there have been wide variations in the actual improvements in fatigue strength achieved. Based on an extensive testing programme organised by the IIW, this report reviews the main methods for weld toe improvement to increase fatigue strength: burr grinding, TIG dressing and hammer and needle peening. The report provides specifications for the practical use of each method, including equipment, weld preparation and operation. It also offers guidance on inspection, quality control and training as well as assessments of fatigue strength and thickness effects possible with each technique. IIW recommendations on methods for improving the fatigue strength of welded joints will allow a more consistent use of these methods and more predictable increases in fatigue strength. Provides specifications for the practical use of each weld toe method, including equipment, weld preparation and operation Offers guidance on inspection, quality control and training, as well as assessments of fatigue strength and thickness effects possible with each technique This report will allow a more consistent use of these methods and more predictable increases in fatigue strength
Download or read book Residual Stresses 2016 written by Thomas M. Holden and published by Materials Research Forum LLC. This book was released on 2017-03-15 with total page 630 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the proceedings of the International Conference on Residual Stresses 10 and is devoted to the prediction/modelling, evaluation, control, and application of residual stresses in engineering materials. New developments, on stress-measurement techniques, on modelling and prediction of residual stresses and on progress made in the fundamental understanding of the relation between the state of residual stress and the material properties, are highlighted. The proceedings offer an overview of the current understanding of the role of residual stresses in materials used in wide ranging application areas.
Download or read book Mechanical Properties and Working of Metals and Alloys written by Amit Bhaduri and published by Springer. This book was released on 2018-05-12 with total page 748 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is intended to serve as core text or handy reference on two key areas of metallic materials: (i) mechanical behavior and properties evaluated by mechanical testing; and (ii) different types of metal working or forming operations to produce useful shapes. The book consists of 16 chapters which are divided into two parts. The first part contains nine chapters which describe tension (including elastic stress – strain relation, relevant theory of plasticity, and strengthening methods), compression, hardness, bending, torsion – pure shear, impact loading, creep and stress rupture, fatigue, and fracture. The second part is composed of seven chapters and covers fundamentals of mechanical working, forging, rolling, extrusion, drawing of flat strip, round bar, and tube, deep drawing, and high-energy rate forming. The book comprises an exhaustive description of mechanical properties evaluated by testing of metals and metal working in sufficient depth and with reasonably wide coverage. The book is written in an easy-to-understand manner and includes many solved problems. More than 150 numerical problems and many multiple choice questions as exercise along with their answers have also been provided. The mathematical analyses are well elaborated without skipping any intermediate steps. Slab method of analysis or free-body equilibrium approach is used for the analytical treatment of mechanical working processes. For hot working processes, different frictional conditions (sliding, sticking and mixed sticking–sliding) have been considered to estimate the deformation loads. In addition to the slab method of analysis, this book also contains slip-line field theory, its application to the static system, and the steady state motion, Further, this book includes upper-bound theorem, and upper-bound solutions for indentation, compression, extrusion and strip drawing. The book can be used to teach graduate and undergraduate courses offered to students of mechanical, aerospace, production, manufacturing and metallurgical engineering disciplines. The book can also be used for metallurgists and practicing engineers in industry and development courses in the metallurgy and metallic manufacturing industries.
