Download or read book Reliable RF Power Amplifier Design Based on a Partitioning Design Approach written by Rui Ma and published by kassel university press GmbH. This book was released on 2010 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: Front cover -- Titelseite -- Impressum -- Acknowledgments -- Contents -- List of Abbreviations and Acronyms -- Abstract -- Zusammenfassung -- Chapter 1 Introduction -- 1.1 Principle of the Partitioning Design Approach -- 1.2 Dissertation Organization -- Chapter 2 Investigation of Planar-Interconnection -- 2.1 Active Chip Device Interconnection -- 2.1.1 Die Attach -- 2.1.2 Wire Bonding Pad-To-Microstrip -- 2.2 Microstrip-to-Microstrip Interconnection -- 2.2.1 Soldering -- 2.2.2 Multi-Wire Bonding -- 2.2.3 Copper Ribbon -- 2.2.4 Silver- Painting -- Chapter 3 Analysis and Modeling of Passive SMD Components -- 3.1 SMD Resistor -- 3.2 SMD Capacitor -- 3.3 SMD Inductor -- Chapter 4 Modeling of AlGaAs/GaAs HEMT Chip Device -- 4.1 AIGaAs/GaGa HEMT Chip -- 4.2 Modeling Approach Overview -- 4.3 Small-Signal Modeling -- 4.3.1 Extrinsic Parameter Extraction -- 4.3.2 Intrinsic Parameter Extraction -- 4.4 Large-Signal Modeling -- 4.4.1 Gate Current and Charge Models -- 4.4.2 Drain Current Model -- 4.4.3 Model Verification -- Chapter 5 Demonstrator Design of a Class-AB Power Amplifier Following -- 5.1 Micro-Packaged Device Characterization -- 5.1.1 Small-Signal Performance -- 5.1.2 Large-Signal Performance -- 5.2 Bias Network Design -- 5.2.1 Drain Bias Network -- 5.2.2 Gate Bias Network -- 5.3 Matching Network Design -- 5.3.1 Matching Impedance Determination -- 5.4 Power Amplifier Performance Evaluation -- 5.4.1 Small-Signal Performance -- 5.4.2 Large-Signal Performance -- Chapter 6 Conclusions and Outlook -- Appendix -- Appendix A THLR In-Fixture Calibration -- Appendix B Precise Determination of Substrate Permittivity -- Appendix C Schematic Circuit of the Designed Power Amplifier Demonstrator -- Appendix D Power Amplifier Design Following the Conventional Design Approach -- References -- Back cover
Download or read book Partitioning Design Approach for the Reliable Design of Highly Efficient RF Power Amplifiers written by Roshanak Lehna and published by kassel university press GmbH. This book was released on 2017-11-13 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: The modern wireless communication systems require modulated signals with wide modulation bandwidth. This, in turns, requires signals with very high dynamic range and peak-to-average power ratio (PAPR). This means that the amplifier in the base-station has to work at a power back-off as large as the dynamic range of the signal, so that the amplifier has a high linearity in this region. For the standard single-stage amplifiers, this large power back-off reduces the efficiency dramatically. In this work, a three-way Doherty power amplifier (DPA) aiming at high power efficiency within a dynamic range of 9.5 dB, is designed and fabricated using partitioning design approach. The partitioning design approach decomposes a complex design task into small-sized, well-controllable, and verifiable subcircuits. This advanced straight forward method has shown very promising results. Using this design approach, a three-way DPA has been designed to demonstrate the advantages of this reliable design technique as well. Based on the design of a single-stage power amplifier and proposing a novel output power combiner, a 6 W three-way DPA has been designed which allows the mandatory load modulation principle in three-way DPA structures to be realized with simpler elements, whereas the design of a standard Doherty combiner would have been very challenging and not practical due to the extremely small value of its characteristic line impedance. The proposed combiner is calculated for a three-way DPA with 2-mm AlGaN/GaN-HEMTs. The simulation result shows a very good load modulation for the amplifier, which confirms the theoretical expectation for a three-way DPA. The efficiency of the designed 6 W three-way DPA at large back-off shows very promising values compared to recently reported amplifiers. The measured IMD3 products confirm the good linearity of the amplifier as well. Accordingly, the proposed power combiner and the design strategy are recommended to be used as the preferred option for designing three-way DPA structures with very high output power.
Download or read book Parameter Extraction and Complex Nonlinear Transistor Models written by Gunter Kompa and published by Artech House. This book was released on 2019-12-31 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: All model parameters are fundamentally coupled together, so that directly measured individual parameters, although widely used and accepted, may initially only serve as good estimates. This comprehensive resource presents all aspects concerning the modeling of semiconductor field-effect device parameters based on gallium-arsenide (GaAs) and gallium nitride (GaN) technology. Metal-semiconductor field-effect transistors (MESFETs), high electron mobility transistors (HEMTs) and heterojunction bipolar transistors (HBTs), their structures and functions, and existing transistor models are also classified. The Shockley model is presented in order to give insight into semiconductor field-effect transistor (FET) device physics and explain the relationship between geometric and material parameters and device performance. Extraction of trapping and thermal time constants is discussed. A special section is devoted to standard nonlinear FET models applied to large-signal measurements, including static-/pulsed-DC and single-/two-tone stimulation. High power measurement setups for signal waveform measurement, wideband source-/load-pull measurement (including envelope source-/load pull) are also included, along with high-power intermodulation distortion (IMD) measurement setup (including envelope load-pull). Written by a world-renowned expert in the field, this book is the first to cover of all aspects of semiconductor FET device modeling in a single volume.
Download or read book Modeling and Design Techniques for RF Power Amplifiers written by Arvind Raghavan and published by John Wiley & Sons. This book was released on 2008-02-04 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt: Achieve higher levels of performance, integration, compactness, and cost-effectiveness in the design and modeling of radio-frequency (RF) power amplifiers RF power amplifiers are important components of any wireless transmitter, but are often the limiting factors in achieving better performance and lower cost in a wireless communication system—presenting the RF IC design community with many challenges. The next-generation technological advances presented in this book are the result of cutting-edge research in the area of large-signal device modeling and RF power amplifier design at the Georgia Institute of Technology, and have the potential to significantly address issues of performance and cost-effectiveness in this area. Richly complemented with hundreds of figures and equations, Modeling and Design Techniques for RF Power Amplifiers introduces and explores the most important topics related to RF power amplifier design under one concise cover. With a focus on efficiency enhancement techniques and the latest advances in the field, coverage includes: Device modeling for CAD Empirical modeling of bipolar devices Scalable modeling of RF MOSFETs Power amplifier IC design Power amplifier design in silicon Efficiency enhancement of RF power amplifiers The description of state-of-the-art techniques makes this book a valuable and handy reference for practicing engineers and researchers, while the breadth of coverage makes it an ideal text for graduate- and advanced undergraduate-level courses in the area of RF power amplifier design and modeling.
Download or read book Signal Processing Techniques for Power Efficient Wireless Communication Systems written by Fernando Gregorio and published by Springer Nature. This book was released on 2019-11-23 with total page 269 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a synthesis of the research carried out in the Laboratory of Signal Processing and Communications (LaPSyC), CONICET, Universidad Nacional del Sur, Argentina, since 2003. It presents models and techniques widely used by the signal processing community, focusing on low-complexity methodologies that are scalable to different applications. It also highlights measures of the performance and impact of each compensation technique. The book is divided into three parts: 1) basic models 2) compensation techniques and 3) applications in advanced technologies. The first part addresses basic architectures of transceivers, their component blocks and modulation techniques. It also describes the performance to be taken into account, regardless of the distortions that need to be compensated. In the second part, several schemes of compensation and/or reduction of imperfections are explored, including linearization of power amplifiers, compensation of the characteristics of analog-to- digital converters and CFO compensation for OFDM modulation. The third and last part demonstrates the use of some of these techniques in modern wireless-communication systems, such as full-duplex transmission, massive MIMO schemes and Internet of Things applications.
Download or read book Audio Power Amplifier Design written by Douglas Self and published by Taylor & Francis. This book was released on 2013-07-04 with total page 1293 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is essential for audio power amplifier designers and engineers for one simple reason...it enables you as a professional to develop reliable, high-performance circuits. The Author Douglas Self covers the major issues of distortion and linearity, power supplies, overload, DC-protection and reactive loading. He also tackles unusual forms of compensation and distortion produced by capacitors and fuses. This completely updated fifth edition includes four NEW chapters including one on The XD Principle, invented by the author, and used by Cambridge Audio. Crosstalk, power amplifier input systems, and microcontrollers in amplifiers are also now discussed in this fifth edition, making this book a must-have for audio power amplifier professionals and audiophiles.
Download or read book High Efficiency RF and Microwave Solid State Power Amplifiers written by Paolo Colantonio and published by John Wiley & Sons. This book was released on 2009-07-08 with total page 514 pages. Available in PDF, EPUB and Kindle. Book excerpt: Do you want to know how to design high efficiency RF and microwave solid state power amplifiers? Read this book to learn the main concepts that are fundamental for optimum amplifier design. Practical design techniques are set out, stating the pros and cons for each method presented in this text. In addition to novel theoretical discussion and workable guidelines, you will find helpful running examples and case studies that demonstrate the key issues involved in power amplifier (PA) design flow. Highlights include: Clarification of topics which are often misunderstood and misused, such as bias classes and PA nomenclatures. The consideration of both hybrid and monolithic microwave integrated circuits (MMICs). Discussions of switch-mode and current-mode PA design approaches and an explanation of the differences. Coverage of the linearity issue in PA design at circuit level, with advice on low distortion power stages. Analysis of the hot topic of Doherty amplifier design, plus a description of advanced techniques based on multi-way and multi-stage architecture solutions. High Efficiency RF and Microwave Solid State Power Amplifiers is: an ideal tutorial for MSc and postgraduate students taking courses in microwave electronics and solid state circuit/device design; a useful reference text for practising electronic engineers and researchers in the field of PA design and microwave and RF engineering. With its unique unified vision of solid state amplifiers, you won’t find a more comprehensive publication on the topic.
Download or read book Advanced Design Techniques for RF Power Amplifiers written by Anna N. Rudiakova and published by Springer Science & Business Media. This book was released on 2006-09-09 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Design Techniques for RF Power Amplifiers provides a deep analysis of theoretical aspects, modelling, and design strategies of RF high-efficiency power amplifiers. The book can be used as a guide by scientists and engineers dealing with the subject and as a text book for graduate and postgraduate students. Although primarily intended for skilled readers, it provides an excellent quick start for beginners.
Download or read book Analog Circuit Design written by Michiel Steyaert and published by Springer Science & Business Media. This book was released on 2002-01-31 with total page 395 pages. Available in PDF, EPUB and Kindle. Book excerpt: This tenth volume concentrates on three topics: scalable analogue circuits; high-speed D/A converters; and RF power amplifiers. Each topic is covered by six papers, written by an expert on that particular topic.
Download or read book Design and Control of RF Power Amplifiers written by Alireza Shirvani and published by Springer Science & Business Media. This book was released on 2013-04-18 with total page 157 pages. Available in PDF, EPUB and Kindle. Book excerpt: Design and Control of RF Power Amplifiers investigates various architectures and concepts for the design and control of radio-frequency (RF) power amplifiers. This book covers merits and challenges of integrating RF power amplifiers in various technologies, and introduces a number of RF power amplifier performance metrics. It provides a thorough review of various power amplifier topologies, followed by a description of approaches and architectures for the control and linearization of these amplifiers. A novel parallel amplifier architecture introduced in this book offers a breakthrough solution to enhancing efficiency in systems using power control. Design and Control of RF Power Amplifiers is a valuable resource for designers, researchers and students in the field of RF integrated circuit design. Detailed and thorough coverage of various concepts in RF power amplifier design makes this book an invaluable guide for both beginners and professionals.
Download or read book High Mixed Voltage Analog and RF Circuit Techniques for Nanoscale CMOS written by Pui-In Mak and published by Springer Science & Business Media. This book was released on 2012-03-20 with total page 161 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents high-/mixed-voltage analog and radio frequency (RF) circuit techniques for developing low-cost multistandard wireless receivers in nm-length CMOS processes. Key benefits of high-/mixed-voltage RF and analog CMOS circuits are explained, state-of-the-art examples are studied, and circuit solutions before and after voltage-conscious design are compared. Three real design examples are included, which demonstrate the feasibility of high-/mixed-voltage circuit techniques. Provides a valuable summary and real case studies of the state-of-the-art in high-/mixed-voltage circuits and systems; Includes novel high-/mixed-voltage analog and RF circuit techniques – from concept to practice; Describes the first high-voltage-enabled mobile-TVRF front-end in 90nm CMOS and the first mixed-voltage full-band mobile-TV Receiver in 65nm CMOS; Demonstrates the feasibility of high-/mixed-voltage circuit techniques with real design examples.
Download or read book Advanced Techniques in RF Power Amplifier Design written by Steve C. Cripps and published by Artech House. This book was released on 2002 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: This much-anticipated volume builds on the author's popular work, RF Power Amplifiers for Wireless Communications (Artech House, 1999), offering you a more in-depth understanding of the theory and design of RF power amplifiers. An invaluable reference tool for RF, digital and system level designers, the book enables you to efficiently design linear RF power amplifiers , and includes detailed discussions on envelope power management schemes and linearization techniques.
Download or read book Science Abstracts written by and published by . This book was released on 1995 with total page 1360 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Bandwidth and Efficiency Enhancement in Radio Frequency Power Amplifiers for Wireless Transmitters written by Karun Rawat and published by Springer Nature. This book was released on 2020-03-05 with total page 390 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on broadband power amplifier design for wireless communication. Nonlinear model embedding is described as a powerful tool for designing broadband continuous Class-J and continuous class F power amplifiers. The authors also discuss various techniques for extending bandwidth of load modulation based power amplifiers, such as Doherty power amplifier and Chireix outphasing amplifiers. The book also covers recent trends on digital as well as analog techniques to enhance bandwidth and linearity in wireless transmitters. Presents latest trends in designing broadband power amplifiers; Covers latest techniques for using nonlinear model embedding in designing power amplifiers based on waveform engineering; Describes the latest techniques for extending bandwidth of load modulation based power amplifiers such as Doherty power amplifier and Chireix outphasing amplifiers; Includes coverage of hybrid analog/digital predistortion as wideband solution for wireless transmitters; Discusses recent trends on on-chip power amplifier design with GaN /GaAs MMICs for high frequency applications.
Download or read book Dissertation Abstracts International written by and published by . This book was released on 2008 with total page 886 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Linear and Switch Mode RF Power Amplifiers written by Abdullah Eroglu and published by CRC Press. This book was released on 2017-09-06 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: RF power amplifiers are implemented in communication, semiconductor wafer processing, magnetic resonance imaging (MRI), and radar systems to produce RF signal with the desired characteristics to perform several critical tasks in the entire system. They can be designed to operate in linear or switch-mode, depending on the specific application. This book explores the design and implementation methods for both linear and switch-mode amplifiers with real world engineering problems. The text discusses phased controlled switch-mode amplifiers and distortion and modulation effects in RF amplifiers. It illustrates the interface and integration of components and sub-systems for RF amplifiers. The material is further reinforced with MATLAB design files.
Download or read book Optimized Class E RF Power Amplifier Design in Bulk CMOS written by Tao Wang and published by ProQuest. This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The telecommunication market calls for the integration of complicated wireless applications. To build RF power amplifiers in CMOS remains challenging due to the non-ideal effects in CMOS. The aim of this thesis is to provide an optimized yet explicit design method for the Class-E amplifiers in CMOS. Taking the finite DC feed inductor into consideration, a simple but accurate numerical design method is proposed by applying polynomial interpolation. Combining with a practical design strategy for non-ideal transistors of finite conductance and parasitic capacitances, a two-staged Class-E power amplifier is implemented in 0.18mum CMOS. The simulation results show that this power amplifier can deliver at least a 23dBm power to a 50Ohm load with 73.5% PAE at 2.4GHz. The good agreement between simulation results and the predicted values validates this design method and its applications in CMOS. This method could be applied to general design cases.
