Download or read book Reliability Testing of Polysilicon For MEMs Devices written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Mission critical applications of MEMS devices require knowledge of the distribution in their material properties and long-term reliability of the small-scale structures. This project reports on a new testing program at Sandia to quantify the strength distribution using samples that reflect the dimensions of critical MEMS components. The strength of polysilicon fabricated with Sandia's SUMMiT 4-layer process was successfully measured using samples with gage sections 2.5[micro]m thick by 1.7[micro]m wide and lengths of 15 and 25[micro]m. These tensile specimens have a freely moving pivot on one end that anchors the sample to the silicon die and prevents off axis loading during testing. Each sample is loaded in uniaxial tension by pulling laterally with a flat tipped diamond in a computer-controlled Nanoindenter. The stress-strain curve is calculated using the specimen cross section and gage length dimensions verified by measuring against a standard in the SEM. The first 48 samples had a means strength of 2.24[+-] 0.35 GPa. Fracture strength measurements grouped into three strength levels, which matched three failure modes observed in post mortem examinations. The seven samples in the highest strength group failed in the gage section (strength of 2.77[+-] 0.04 GPa), the moderate strength group failed at the gage section fillet and the lowest strength group failed at a dimple in the hub. With this technique, multiple tests can be programmed at one time and performed without operator assistance at a rate of 20-30 per day allowing the collection of significant populations of data. Since the new test geometry has been proven, the project is moving to test the distributions seen from real geometric features typical to MEMS such as the effect of gage length, fracture toughness, bonding between layers, etch holes, dimples and shear of gear teeth.
Download or read book Reliability of MEMS written by Osamu Tabata and published by John Wiley & Sons. This book was released on 2014-07-21 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: This first book to cover exclusively and in detail the principles, tools and methods for determining the reliability of microelectromechanical materials, components and devices covers both component materials as well as entire MEMS devices. Divided into two major parts, following a general introductory chapter to reliability issues, the first part looks at the mechanical properties of the materials used in MEMS, explaining in detail the necessary measuring technologies -- nanoindenters, bulge methods, bending tests, tensile tests, and others. Part Two treats the actual devices, organized by important device categories such as pressure sensors, inertial sensors, RF MEMS, and optical MEMS.
Download or read book Reliability Testing and Characterization of MEMS MOEMS written by and published by . This book was released on 2001 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book MEMS Reliability written by Allyson L. Hartzell and published by Springer Science & Business Media. This book was released on 2010-11-02 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt: The successful launch of viable MEMs product hinges on MEMS reliability, the reliability and qualification for MEMs based products is not widely understood. Companies that have a deep understanding of MEMs reliability view the information as a competitive advantage and are reluctant to share it. MEMs Reliability, focuses on the reliability and manufacturability of MEMS at a fundamental level by addressing process development and characterization, material property characterization, failure mechanisms and physics of failure (POF), design strategies for improving yield, design for reliability (DFR), packaging and testing.
Download or read book Reliability of MEMS written by Osamu Tabata and published by John Wiley & Sons. This book was released on 2008-09-08 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edition of 'Reliability of MEMS' was originally published in the successful series 'Advanced Micro & Nanosystems'. Here, one of the most important hurdles to commercialization for microelectromechanical systems is covered in detail: the reliability of MEMS materials and devices. Due to their microscale size combined with novel functionalities, a whole new category of challenges arises, and proper determination of a given device's reliability is instrumental in determining its range of usability and application fields. Any kind of gadget's performance, lifetime and safety will depend on the continued and predictable functioning of both the electronic as well as the micromechanical parts. MEMS reliability therefore can be as serious as human life-and-death matters - quite literally in the case of roll-over sensors for cars, for example.
Download or read book Strength of Polysilicon for MEMS Devices written by and published by . This book was released on 1999 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: The safe, secure and reliable application of Microelectromechanical Systems (MEMS) devices requires knowledge about the distribution in material and mechanical properties of the small-scale structures. A new testing program at Sandia is quantifying the strength distribution using polysilicon samples that reflect the dimensions of critical MEMS components. The strength of polysilicon fabricated at Sandia's Microelectronic Development Laboratory was successfully measured using samples 2.5 microns thick, 1.7 microns wide with lengths between 15 and 25 microns. These tensile specimens have a freely moving hub on one end that anchors the sample to the silicon die and allows free rotation. Each sample is loaded in uniaxial tension by pulling laterally with a flat tipped diamond in a computer-controlled Nanoindenter. The stress-strain curve is calculated using the specimen cross section and gage length dimensions verified by measuring against a standard in the SEM.
Download or read book Handbook of Silicon Based MEMS Materials and Technologies written by Markku Tilli and published by William Andrew. This book was released on 2015-09-02 with total page 827 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Handbook of Silicon Based MEMS Materials and Technologies, Second Edition, is a comprehensive guide to MEMS materials, technologies, and manufacturing that examines the state-of-the-art with a particular emphasis on silicon as the most important starting material used in MEMS. The book explains the fundamentals, properties (mechanical, electrostatic, optical, etc.), materials selection, preparation, manufacturing, processing, system integration, measurement, and materials characterization techniques, sensors, and multi-scale modeling methods of MEMS structures, silicon crystals, and wafers, also covering micromachining technologies in MEMS and encapsulation of MEMS components. Furthermore, it provides vital packaging technologies and process knowledge for silicon direct bonding, anodic bonding, glass frit bonding, and related techniques, shows how to protect devices from the environment, and provides tactics to decrease package size for a dramatic reduction in costs. Provides vital packaging technologies and process knowledge for silicon direct bonding, anodic bonding, glass frit bonding, and related techniques Shows how to protect devices from the environment and decrease package size for a dramatic reduction in packaging costs Discusses properties, preparation, and growth of silicon crystals and wafers Explains the many properties (mechanical, electrostatic, optical, etc.), manufacturing, processing, measuring (including focused beam techniques), and multiscale modeling methods of MEMS structures Geared towards practical applications rather than theory
Download or read book MEMS Reliability for Critical and Space Applications written by Russell A. Lawton and published by SPIE-International Society for Optical Engineering. This book was released on 1999 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: A selection of scientific papers on the reliability of microelectromechanical systems (MEMS) for critical and space applications.
Download or read book Mechanics of Microsystems written by Alberto Corigliano and published by John Wiley & Sons. This book was released on 2017-11-20 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechanics of Microsystems Alberto Corigliano, Raffaele Ardito, Claudia Comi, Attilio Frangi, Aldo Ghisi and Stefano Mariani, Politecnico di Milano, Italy A mechanical approach to microsystems, covering fundamental concepts including MEMS design, modelling and reliability Mechanics of Microsystems takes a mechanical approach to microsystems and covers fundamental concepts including MEMS design, modelling and reliability. The book examines the mechanical behaviour of microsystems from a ‘design for reliability’ point of view and includes examples of applications in industry. Mechanics of Microsystems is divided into two main parts. The first part recalls basic knowledge related to the microsystems behaviour and offers an overview on microsystems and fundamental design and modelling tools from a mechanical point of view, together with many practical examples of real microsystems. The second part covers the mechanical characterization of materials at the micro-scale and considers the most important reliability issues (fracture, fatigue, stiction, damping phenomena, etc) which are fundamental to fabricate a real working device. Key features: Provides an overview of MEMS, with special focus on mechanical-based Microsystems and reliability issues. Includes examples of applications in industry. Accompanied by a website hosting supplementary material. The book provides essential reading for researchers and practitioners working with MEMS, as well as graduate students in mechanical, materials and electrical engineering.
Download or read book Fatigue of Polycrystalline Silicon in MEMS Devices written by Angela S. Choy and published by . This book was released on 1999 with total page 60 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced Mechatronics and MEMS Devices II written by Dan Zhang and published by Springer. This book was released on 2016-10-18 with total page 719 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book introduces the state-of-the-art technologies in mechatronics, robotics, and MEMS devices in order to improve their methodologies. It provides a follow-up to "Advanced Mechatronics and MEMS Devices" (2013) with an exploration of the most up-to-date technologies and their applications, shown through examples that give readers insights and lessons learned from actual projects. Researchers on mechatronics, robotics, and MEMS as well as graduate students in mechanical engineering will find chapters on: Fundamental design and working principles on MEMS accelerometers Innovative mobile technologies Force/tactile sensors development Control schemes for reconfigurable robotic systems Inertial microfluidics Piezoelectric force sensors and dynamic calibration techniques ...And more. Authors explore applications in the areas of agriculture, biomedicine, advanced manufacturing, and space. Micro-assembly for current and future industries is also considered, as well as the design and development of micro and intelligent manufacturing.
Download or read book MEMS Reliability written by and published by . This book was released on 2000 with total page 169 pages. Available in PDF, EPUB and Kindle. Book excerpt: The burgeoning new technology of Micro-Electro-Mechanical Systems (MEMS) shows great promise in the weapons arena. We can now conceive of micro-gyros, micro-surety systems, and micro-navigators that are extremely small and inexpensive. Do we want to use this new technology in critical applications such as nuclear weapons? This question drove us to understand the reliability and failure mechanisms of silicon surface-micromachined MEMS. Development of a testing infrastructure was a crucial step to perform reliability experiments on MEMS devices and will be reported here. In addition, reliability test structures have been designed and characterized. Many experiments were performed to investigate failure modes and specifically those in different environments (humidity, temperature, shock, vibration, and storage). A predictive reliability model for wear of rubbing surfaces in microengines was developed. The root causes of failure for operating and non-operating MEMS are discussed. The major failure mechanism for operating MEMS was wear of the polysilicon rubbing surfaces. Reliability design rules for future MEMS devices are established.
Download or read book Reliability of MEMS written by Osamu Tabata and published by John Wiley & Sons. This book was released on 2008-02-04 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt: This first book to cover exclusively and in detail the principles, tools and methods for determining the reliability of microelectromechanical materials, components and devices covers both component materials as well as entire MEMS devices. Divided into two major parts, following a general introductory chapter to reliability issues, the first part looks at the mechanical properties of the materials used in MEMS, explaining in detail the necessary measuring technologies -- nanoindenters, bulge methods, bending tests, tensile tests, and others. Part Two treats the actual devices, organized by important device categories such as pressure sensors, inertial sensors, RF MEMS, and optical MEMS.
Download or read book MEMS Reliability for Critical Applications written by Russell A. Lawton and published by SPIE-International Society for Optical Engineering. This book was released on 2000 with total page 162 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Reliability Packaging Testing and Characterization of MEMS MOEMS IV written by Danelle Mary Tanner and published by SPIE-International Society for Optical Engineering. This book was released on 2005 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of SPIE present the original research papers presented at SPIE conferences and other high-quality conferences in the broad-ranging fields of optics and photonics. These books provide prompt access to the latest innovations in research and technology in their respective fields. Proceedings of SPIE are among the most cited references in patent literature.
Download or read book Tribology Issues and Opportunities in MEMS written by Bharat Bhushan and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 652 pages. Available in PDF, EPUB and Kindle. Book excerpt: Micro Electro Mechanical Systems (MEMS) is already about a billion dollars a year industry and is growing rapidly. So far major emphasis has been placed on the fabrication processes for various devices. There are serious issues related to tribology, mechanics, surfacechemistry and materials science in the operationand manufacturingof many MEMS devices and these issues are preventing an even faster commercialization. Very little is understood about tribology and mechanical properties on micro- to nanoscales of the materials used in the construction of MEMS devices. The MEMS community needs to be exposed to the state-of-the-artoftribology and vice versa. Fundamental understanding of friction/stiction, wear and the role of surface contamination and environmental debris in micro devices is required. There are significantadhesion, friction and wear issues in manufacturing and actual use, facing the MEMS industry. Very little is understood about the tribology of bulk silicon and polysilicon films used in the construction ofthese microdevices. These issues are based on surface phenomenaand cannotbe scaled down linearly and these become increasingly important with the small size of the devices. Continuum theory breaks down in the analyses, e. g. in fluid flow of micro-scale devices. Mechanical properties ofpolysilicon and other films are not well characterized. Roughness optimization can help in tribological improvements. Monolayers of lubricants and other materials need to be developed for ultra-low friction and near zero wear. Hard coatings and ion implantation techniques hold promise.
Download or read book Component Reliability for Electronic Systems written by Titu I. Băjenescu and published by Artech House. This book was released on 2010 with total page 706 pages. Available in PDF, EPUB and Kindle. Book excerpt: The main reason for the premature breakdown of today's electronic products (computers, cars, tools, appliances, etc.) is the failure of the components used to build these products. Today professionals are looking for effective ways to minimize the degradation of electronic components to help ensure longer-lasting, more technically sound products and systems. This practical book offers engineers specific guidance on how to design more reliable components and build more reliable electronic systems. Professionals learn how to optimize a virtual component prototype, accurately monitor product reliability during the entire production process, and add the burn-in and selection procedures that are the most appropriate for the intended applications. Moreover, the book helps system designers ensure that all components are correctly applied, margins are adequate, wear-out failure modes are prevented during the expected duration of life, and system interfaces cannot lead to failure.
