Download or read book Refractory Metal Alloys Metallurgy and Technology written by I. Machlin and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 493 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication documents Proceedings of the Symposium on Metal lurgy and Technology of Refractory Metal Alloys, held in Washington, D.C. at the Washington Hilton Hotel on April 25-26, 1968, under sponsorship of the Refractory Metals Committee, Institute of Metals Division, of the Metallurgical Society of AIME, and the National Aeronautics and Space Administration. The Symposium presented critical reviews of selected topics in refractory metal alloys, thereby contributing to an in-depth understanding of the state-of-the-art, and establishing a base line for further research, development, and application. This Symposium is fifth in a series of conferences on refractory metals, sponsored by the Metallurgical Society of AlME. Publications issuing from the conferences are valuable technical and historical source books, tracing the evolution of refractory metals from early laboratory alloying studies to their present status as useful engineering materials. Refractory metals are arbitrarily defined by melting point. A 0 melting temperature of over 3500 F was selected as the minimum for this Symposium, thus excluding chromium and vanadium, which logically could be treated with other refractory metals in Groups VA and VIA of the periodic table. The Refractory Metals Committee is planning reviews of chromium and vanadium in subsequent conferences.
Download or read book Physical Metallurgy of Refractory Metals and Alloys written by E. M. Savitskii and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: The principal reasons which induced the authors to write this book and the features of the book are set forth in the preface to the Russian edition. That section of the science of metals which in Russian is called "metallovedenie" or the "physical chemistry of metals" is generally referred to in scientific and technical literature published in the English language by the term "physical metallurgy." These concepts are much broader than the term" metallography," used in the scientific and technical literature of various countries, and applied solely to research on the interrelationships of the structure and proper ties of metals and alloys. Each science must have its own subject and its own method of research. Certainly, all specialists will agree that metals and alloys, including their solid solutions, mechanical mix tures, and metallic compounds, form the subject of "physical metallurgy" or "physical chemis try of metals." The aim of this science. is to produce a theory and to elucidate the experimental relationships which ought finally to make it possible to calculate quantitatively alloys Of given properties for any working conditions and parameters.
Download or read book ASM Metals Reference Book 3rd Edition written by Michael Bauccio and published by ASM International. This book was released on 1993-01-01 with total page 628 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference book makes it easy for anyone involved in materials selection, or in the design and manufacture of metallic structural components to quickly screen materials for a particular application. Information on practically all ferrous and nonferrous metals including powder metals is presented in tabular form for easy review and comparison between different materials. Included are chemical compositions, physical and mechanical properties, manufacturing processes, applications, pertinent specifications and standards, and test methods. Contents Overview: Glossary of metallurgical terms Selection of structural materials (specifications and standards, life cycle and failure modes, materials properties and design, and properties and applications) Physical data on the elements and alloys Testing and inspection Chemical composition and processing characteristics
Download or read book Alloys written by Fathi Habashi and published by John Wiley & Sons. This book was released on 2008-11-21 with total page 321 pages. Available in PDF, EPUB and Kindle. Book excerpt: In industry very few metals are used in their pure form; the majority are employed as a combination of a metal with other metals, nonmetals or metalloids. In this way some specific properties are improved, making the alloy more attractive than the pure metal. The present work comprises essential information on alloys in one compact volume. Classification, properties, preparation, applications, and economic aspects are discussed for alloy steels, primary-metal alloys, light-metal alloys, and some other alloy systems. The work is based on more than 30 articles from Ullmann's Encyclopedia of Industrial Chemistry and represents the effort of over 60 specialists. It supplies hundreds of top-quality illustrations, diagrams, and charts and provides hand-picked references for further study. An introductory overview of the subject is provided by the editor. The book is a handy yet authoritative reference work for the practicing metallurgist, but also for physical metallurgists, engineers and scientists in industry.
Download or read book Ultra High Temperature Materials I written by Igor L. Shabalin and published by Springer. This book was released on 2016-09-27 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This exhaustive work in three volumes with featuring cross-reference system provides a thorough overview of ultra-high temperature materials – from elements and chemical compounds to alloys and composites. Topics included are physical (crystallographic, thermodynamic, thermo-physical, electrical, optical, physico-mechanical, nuclear) and chemical (solid-state diffusion, interaction with chemical elements and compounds, interaction with gases, vapours and aqueous solutions) properties of the individual physico-chemical phases and multi-phase materials with melting (or sublimation) points over or about 2500 °C. The first volume focuses on carbon (graphite/graphene) and refractory metals (W, Re, Os, Ta, Mo, Nb, Ir). The second and third volumes are dedicated solely to refractory (ceramic) compounds (oxides, nitrides, carbides, borides, silicides) and to the complex materials – refractory alloys, carbon and ceramic composites, respectively. It will be of interest to researchers, engineers, postgraduate, graduate and undergraduate students in various disciplines alike. The reader is provided with the full qualitative and quantitative assessment for the materials, which could be applied in various engineering devices and environmental conditions at ultra-high temperatures, on the basis of the latest updates in the field of physics, chemistry, materials science, nanotechnology and engineering.
Download or read book ASM Specialty Handbook written by Joseph R. Davis and published by ASM International. This book was released on 1997-01-01 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials covered include carbon, alloy and stainless steels; alloy cast irons; high-alloy cast steels; superalloys; titanium and titanium alloys; refractory metals and alloys; nickel-chromium and nickel-thoria alloys; structural intermetallics; structural ceramics, cermets, and cemented carbides; and carbon-composites.
Download or read book Structural Materials for Generation IV Nuclear Reactors written by Pascal Yvon and published by Woodhead Publishing. This book was released on 2016-08-27 with total page 684 pages. Available in PDF, EPUB and Kindle. Book excerpt: Operating at a high level of fuel efficiency, safety, proliferation-resistance, sustainability and cost, generation IV nuclear reactors promise enhanced features to an energy resource which is already seen as an outstanding source of reliable base load power. The performance and reliability of materials when subjected to the higher neutron doses and extremely corrosive higher temperature environments that will be found in generation IV nuclear reactors are essential areas of study, as key considerations for the successful development of generation IV reactors are suitable structural materials for both in-core and out-of-core applications. Structural Materials for Generation IV Nuclear Reactors explores the current state-of-the art in these areas. Part One reviews the materials, requirements and challenges in generation IV systems. Part Two presents the core materials with chapters on irradiation resistant austenitic steels, ODS/FM steels and refractory metals amongst others. Part Three looks at out-of-core materials. Structural Materials for Generation IV Nuclear Reactors is an essential reference text for professional scientists, engineers and postgraduate researchers involved in the development of generation IV nuclear reactors. Introduces the higher neutron doses and extremely corrosive higher temperature environments that will be found in generation IV nuclear reactors and implications for structural materials Contains chapters on the key core and out-of-core materials, from steels to advanced micro-laminates Written by an expert in that particular area
Download or read book Electric Refractory Materials written by Yukinobu Kumashiro and published by CRC Press. This book was released on 2000-08-24 with total page 778 pages. Available in PDF, EPUB and Kindle. Book excerpt: An exploration of electric refractory materials, this book covers developments of blue light-emitting diodes using GaN-based nitrides for laser and high-temperature and -frequency devices. Electric Refractory Materials introduces growth and evaluation standards of films and bulk crystals, with consideration of band structure, surface electronic structure, and lattice vibrations. It also covers heat capacity and thermal conductivity, irradiation properties, and selective surfaces. Focusing on diamond material, the book examines its synthesis and characterization as well as its electrical, optical, and conductive properties. The book also discusses the use of silicon carbide, boron compounds, and other material used in electronic and light-emitting devices.
Download or read book Refractory Metal Alloys written by I. Machlin and published by . This book was released on 1968 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Refractory Metals written by F. H. Buttner and published by . This book was released on 1968 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: The memorandum discusses the supply, production, consumption, and applications of the refractory metals, columbium, tantalum, molybdenum, tungsten, and rhenium. Lists of manufacturers of mill products of these metals are included. (Author).
Download or read book High temperature Oxidation resistant Coatings written by National Research Council (U.S.). Committee on Coatings and published by National Academies. This book was released on 1970-01-01 with total page 236 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Aerospace Materials and Material Technologies written by N. Eswara Prasad and published by Springer. This book was released on 2016-11-11 with total page 586 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is a comprehensive compilation of chapters on materials (both established and evolving) and material technologies that are important for aerospace systems. It considers aerospace materials in three Parts. Part I covers Metallic Materials (Mg, Al, Al-Li, Ti, aero steels, Ni, intermetallics, bronzes and Nb alloys); Part II deals with Composites (GLARE, PMCs, CMCs and Carbon based CMCs); and Part III considers Special Materials. This compilation has ensured that no important aerospace material system is ignored. Emphasis is laid in each chapter on the underlying scientific principles as well as basic and fundamental mechanisms leading to processing, characterization, property evaluation and applications. This book will be useful to students, researchers and professionals working in the domain of aerospace materials.
Download or read book Alloy Materials and Their Allied Applications written by Inamuddin and published by John Wiley & Sons. This book was released on 2020-06-16 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: Alloy Materials and Their Allied Applications provides an in-depth overview of alloy materials and applications. The 11 chapters focus on the fabrication methods and design of corrosion-resistant, magnetic, biodegradable, and shape memory alloys. The industrial applications in the allied areas, such as biomedical, dental implants, abrasive finishing, surface treatments, photocatalysis, water treatment, and batteries, are discussed in detail. This book will help readers solve fundamental and applied problems faced in the field of allied alloys applications.
Download or read book Sintering of Advanced Materials written by Zhigang Zak Fang and published by Elsevier. This book was released on 2010-09-27 with total page 502 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sintering is a method for manufacturing components from ceramic or metal powders by heating the powder until the particles adhere to form the component required. The resulting products are characterised by an enhanced density and strength, and are used in a wide range of industries. Sintering of advanced materials: fundamentals and processes reviews important developments in this technology and its applicationsPart one discusses the fundamentals of sintering with chapters on topics such as the thermodynamics of sintering, kinetics and mechanisms of densification, the kinetics of microstructural change and liquid phase sintering. Part two reviews advanced sintering processes including atmospheric sintering, vacuum sintering, microwave sintering, field/current assisted sintering and photonic sintering. Finally, Part three covers sintering of aluminium, titanium and their alloys, refractory metals, ultrahard materials, thin films, ultrafine and nanosized particles for advanced materials.With its distinguished editor and international team of contributors, Sintering of advanced materials: fundamentals and processes reviews the latest advances in sintering and is a standard reference for researchers and engineers involved in the processing of ceramics, powder metallurgy, net-shape manufacturing and those using advanced materials in such sectors as electronics, automotive and aerospace engineering. Explores the thermodynamics of sintering including sinter bonding and densification Chapters review a variety of sintering methods including atmosphere, vacuum, liquid phase and microwave sintering Discusses sintering of a variety of materials featuring refractory metals, super hard materials and functionally graded materials
Download or read book The Science and Engineering of Materials written by Donald R. Askeland and published by Springer. This book was released on 2013-11-11 with total page 870 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Science and Engineering of Materials, Third Edition, continues the general theme of the earlier editions in providing an understanding of the relationship between structure, processing, and properties of materials. This text is intended for use by students of engineering rather than materials, at first degree level who have completed prerequisites in chemistry, physics, and mathematics. The author assumes these stu dents will have had little or no exposure to engineering sciences such as statics, dynamics, and mechanics. The material presented here admittedly cannot and should not be covered in a one-semester course. By selecting the appropriate topics, however, the instructor can emphasise metals, provide a general overview of materials, concentrate on mechani cal behaviour, or focus on physical properties. Additionally, the text provides the student with a useful reference for accompanying courses in manufacturing, design, or materials selection. In an introductory, survey text such as this, complex and comprehensive design problems cannot be realistically introduced because materials design and selection rely on many factors that come later in the student's curriculum. To introduce the student to elements of design, however, more than 100 examples dealing with materials selection and design considerations are included in this edition.
Download or read book ENGINEERING MATERIALS written by C. P. SHARMA and published by PHI Learning Pvt. Ltd.. This book was released on 2003-01-01 with total page 270 pages. Available in PDF, EPUB and Kindle. Book excerpt: This compact and student-friendly book provides a thorough understanding of properties of metallic materials and explains the metallurgy of a large number of metals and alloys. The text first exposes the reader to the structure-property correlation of materials, that form the basis for predicting their behaviour during manufacturing and other service conditions, and then discusses the factors governing the selection of a material for specific applications. It further introduces the various specifications/designations, (including AISI/SAE system) used for steels and the alloying elements. The text also gives detailed coverage on mechanical behaviour of other engineering metals including Al, Mg, Cu, Ni, Zn and Pb. Profusely illustrated with graphs and tables, the book presents a large number of questions and answers framed on the pattern of the university examinations. It thus enables the students to format compact and to-the-point answers. This book would be highly valued by students of metallurgical engineering and also those pursuing various other engineering as well as polytechnic courses, besides professionals who deal with selection of materials.
Download or read book The Structure of Metals and Alloys written by William Hume-Rothery and published by . This book was released on 1950 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt:
