Download or read book Reactive Sputter Deposition of Vanadium Oxide written by Steven D. Hansen and published by . This book was released on 1984 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book REACTIVE SPUTTER DEPOSITION OF VANADIUM NICKEL AND MOLYBDENUM OXIDE THIN FILMS FOR USE IN UNCOOLED INFRARED IMAGING written by Yao Jin and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A vanadium oxide (VO x) thin film is the most common imaging layer used in commercial uncooled focal plane arrays for infrared cameras. These VOx thin films have an x value ranging from 1.3 to 2 and have low resistivity (0.1 to 10 [omega] cm), high temperature coefficient of resistance (TCR) (-2 to -3 %/K), and low 1/f noise. Reactive ion beam sputtering is typically used to deposit these VOx thin films for commercial thermal imaging cameras. However, the reactive ion beam deposition system for the VOx is reported to have less than desirable throughput and a narrow process window. In this work, the potential for reactive pulsed-dc magnetron sputtering of nanocomposite VOx thin films for microbolometer applications was investigated. VOx thin films with resistivity from 10-4 to 105 [omega] cm with a TCR from 0 to -4.3 %/K were deposited by reactive sputtering from a metallic vanadium target in argon/oxygen mixtures with substrate bias. Magnetron sputtered VOx shows bolometric properties comparable to those of commercial-grade IBD prepared VOx. Important limitations for manufacturing implementation of reactive magnetron sputtering such as hysteresis oxidation and non-uniform oxidation of the vanadium target surface were evaluated. The VOx film deposition rate, resistivity, and temperature coefficient of resistance were correlated to oxygen to argon ratio, processing pressure, target-to-substrate distance, and oxygen inlet positions. To deposit VOx in the resistivity range of 0.1--10 [omega] cm with good uniformity and process control, it was found that a lower processing pressure, larger target-to-substrate distance, and an oxygen inlet near the substrate are useful. Other processing methods employing magnetron sputtering were investigated such as co-sputtering of V and V2O5 target, sputtering from a VC target, a V2O5 target, and a V2Ox target but initial investigation of these methods did not yield a superior process to the simple sputtering of a pure metallic vanadium target. Another technique, biased target ion beam deposition (BTIBD), was investigated for deposition VOx thin films with potential alloy additions. In this BTIBD system, ions with energy lower than 25 eV were generated remotely and vanadium targets are negatively biased independently for sputtering. High TCR (

Download or read book Reactive Sputter Deposition written by Diederik Depla and published by Springer Science & Business Media. This book was released on 2008-06-24 with total page 584 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this valuable work, all aspects of the reactive magnetron sputtering process, from the discharge up to the resulting thin film growth, are described in detail, allowing the reader to understand the complete process. Hence, this book gives necessary information for those who want to start with reactive magnetron sputtering, understand and investigate the technique, control their sputtering process and tune their existing process, obtaining the desired thin films.

Download or read book Effect of Rf Substrate Bias on Vanadium Oxide Thin Films During Reactive Pulsed Dc Magnetron Sputter Deposition written by Hitesh Arjun Basantani and published by . This book was released on 2011 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Process Parameter growth Environment film Property Relationships for Radio Frequency Reactive Sputter Deposited Vanadium Oxides in Rare Gas oxygen Discharges written by Nada M. Abuhadba and published by . This book was released on 1992 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Low Temperature Film Growth of the Oxides of Zinc Aluminum and Vanadium and Related Systems Oxides of Gold and Germanium Nitrides of Aluminum and Tungsten by Reactive Sputter Deposition written by Carolyn R. Aita and published by . This book was released on 1988 with total page 140 pages. Available in PDF, EPUB and Kindle. Book excerpt: The research involved investigation of process parameter growth environment film property relationships for various binary oxide and nitride films grown on unheated substrates by reactive sputter deposition using an elemental target. In situ optical emission spectroscopy and glow discharge mass spectrometry were used to determine gas phase species in the plasma volume. A battery of techniques were used to characterize (post-deposition) film crystallography, chemistry, microstructure, electrical resistivity, and optical behavior. Keywords: Sputter deposition, Glow discharges, Glow discharge diagnostics, Optical emission, Mass spectrometry, Aluminum oxide, Vanadium, Pentoxide, Gold oxide, Tungsten nitride, Aluminum nitride, Germanium dioxide.

Download or read book Reactive sputter Deposition Characterization and Application of Ruthenium Oxide Thin Films written by Qi Wang and published by . This book was released on 1996 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Vanadium Oxide Thin Films Obtained by Thermal Annealing of Layers Deposited by RF Magnetron Sputtering at Room Temperature written by Hernan M. R. and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This chapter describes a new deposition method proposed to achieve Vanadium Oxide VOx/V2O5 thin films with high temperature coefficient of resistance (TCR), intended to be used as functional material in IR microsensors (bolometers). The main aim of the work is to attain a deposition method compatible with the lift-off microstructuring technique in order to avoid the use of a reactive-ion etching (RIE) process step to selectively remove the VOx/V2O5 deposited layer in the course of the definition of the bolometer geometry, preventing the harmful effects linked to the spatial variability and the lack of selectivity of the RIE process. The proposed technique makes use of a two-stage process to produce the well-controlled VOx or V2O5 thin films by applying a suitable thermal annealing to a previously deposited layer, which was obtained before at room temperature by RF magnetron sputtering and patterned by lift-off. A set of measurements has been carried out with thin films attained in order to check the quality and properties of the materials achieved with this method. The results reached with V2O5 pure phase films are consistent with a charge transport model based on the small polarons hopping derived from Mott's model under the Schnakenberg form.

Download or read book Handbook of Sputter Deposition Technology written by Kiyotaka Wasa and published by William Andrew. This book was released on 2012-11-20 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thoroughly updated new edition includes an entirely new team of contributing authors with backgrounds specializing in the various new applications of sputtering technology. It forms a bridge between fundamental theory and practical application, giving an insight into innovative new materials, devices and systems. Organized into three parts for ease of use, this Handbook introduces the fundamentals of thin films and sputtering deposition, explores the theory and practices of this field, and also covers new technology such as nano-functional materials and MEMS. Wide varieties of functional thin film materials and processing are described, and experimental data is provided with detailed examples and theoretical descriptions. A strong applications focus, covering current and emerging technologies, including nano-materials and MEMS (microelectrolmechanical systems) for energy, environments, communications, and/or bio-medical field. New chapters on computer simulation of sputtering and MEMS completes the update and insures that the new edition includes the most current and forward-looking coverage available All applications discussed are supported by theoretical discussions, offering readers both the "how" and the "why" of each technique 40% revision: the new edition includes an entirely new team of contributing authors with backgrounds specializing in the various new applications that are covered in the book and providing the most up-to-date coverage available anywhere

Download or read book Intelligent Coatings for Corrosion Control written by Atul Tiwari and published by Butterworth-Heinemann. This book was released on 2014-10-25 with total page 747 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intelligent Coatings for Corrosion Control covers the most current and comprehensive information on the emerging field of intelligent coatings. The book begins with a fundamental discussion of corrosion and corrosion protection through coatings, setting the stage for deeper discussion of the various types of smart coatings currently in use and in development, outlining their methods of synthesis and characterization, and their applications in a variety of corrosion settings. Further chapters provide insight into the ongoing research, current trends, and technical challenges in this rapidly progressing field. Reviews fundamentals of corrosion and coatings for corrosion control before delving into a discussion of intelligent coatings—useful for researchers and grad students new to the subject Covers the most current developments in intelligent coatings for corrosion control as presented by top researchers in the field Includes many examples of current and potential applications of smart coatings to a variety of corrosion problems

Download or read book Physical vapor deposition and thermal stability of hard oxide coatings written by Ludvig Landälv and published by Linköping University Electronic Press. This book was released on 2019-04-26 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt: The state-of-the-art tools for machining metals are primarily based on a metal-ceramic composite (WC-Co) coated with different combinations of carbide, nitride, and oxide coatings. Combinations of these coating materials are optimized to withstand specific wear conditions. Oxide coatings, mainly α-Al2O3, are especially desired because of their high hot-hardness, chemical inertness with respect to the workpiece, and their low friction. The search for possible alloy elements, which may facilitate the deposition of such oxides by means of physical vapor deposition (PVD) techniques, has been the goal of this thesis. The sought alloy should form thermodynamically stable or metastable compounds, compatible with the temperature of use in metal cutting application. This thesis deals with process development and coating characterization of such new oxide alloy thin films, focusing on the Al-V-O, Al-Cr-Si-O, and Cr-Zr-O systems. Alloying aluminum oxide with iso-valent vanadium is a candidate for forming the desired alloys. Therefore, coatings of (Al1-xVx)2O3, with x ranging from 0 to 1, were deposited with reactive sputter deposition. X-ray diffraction showed three different crystal structures depending on V-metal fraction in the coating: α-V2O3 rhombohedral structure for 100 at.% V, a defect spinel structure for the intermediate region, (63 - 42 at.% V), and a gamma-alumina-like solid solution at lower V-content, (18 and 7 at.%), were observed, the later was shifted to larger d-spacing compared to the pure γ-Al2O3 sample obtained if deposited with only Al-target. Annealing the Al-rich coatings in air resulted in formation of V2O5 crystals on the surface of the coating after annealing to 500 °C for 42 at.% V and 700 °C for 18 at.% V metal fraction respectively. The highest thermal stability was shown for pure γ-Al2O3-coating which transformed to α-Al2O3 after annealing to 1100° C. Highest hardness was observed for the Al-rich oxides, ~24 GPa. The hardness then decreases with increasing V-content, larger than 7 at.% V metal fraction. Doping the Al2O3 coating with 7 at.% V resulted in a significant surface smoothening compared to the binary oxide. The measured hardness after annealing in air decreased in conjunction with the onset of further oxidation of the coatings. This work increases the understanding of this complicated material system with respect to possible phases formed with pulsed DC magnetron sputtering deposition as well as their response to annealing in air. The inherent difficulties of depositing insulating oxide films with PVD, requiring a closed electrical circuit, makes the investigation of process stability an important part of this research. In this context, I investigated the influence of adding small amount of Si in Al-Cr cathode on the coating properties in a pulsed DC industrial cathodic arc system and the plasma characteristics, process parameters, and coating properties in a lab DC cathodic arc system. Si was chosen here due to a previous study showing improved erosion behavior of Al-Cr-Si over pure Al-Cr cathode without Si incorporation in the coating. The effect of Si in the Al-Cr cathode in the industrial cathodic arc system showed slight improvements on the cathode erosion but Si was found in all coatings where Si was added in the cathode. The Si addition promoted the formation of the B1-like metastable cubic oxide phase and the incorporation led to reduced or equal hardness values compared to the corresponding Si-free processes. The DC-arc plasma study on the same material system showed only small improvements in the cathode erosion and process stability (lower pressure and cathode voltage) when introducing 5 at.% Si in the Al70Cr30-cathode. The presence of volatile SiO species could be confirmed through plasma analysis, but the loss of Si through these species was negligible, since the coating composition matched the cathode composition also under these conditions. The positive effect of added Si on the process stability at the cathode surface, should be weighed against Si incorporation in the coating. This incorporation seems to lead to a reduction in mechanical properties in the as-deposited coatings and promote the formation of a B1-like cubic metastable oxide structure for the (Al,Cr)2O3 oxide. This formation may or may not be beneficial for the final application since literature indicates a slight stabilization of the metastable phase upon Si-incorporation, contrary to the effect of Cr, which stabilizes the α-phase. The thermal stability of alloys for metal cutting application is crucial for their use. Previous studies on another alloy system, Cr-Zr-O, had shown solid solution, for Cr-rich compositions in that material system, in the sought corundum structure. The thermal stability of α-Cr0.28Zr0.10O0.61 coating deposited by reactive radio frequency (RF)-magnetron sputtering at 500 °C was therefore investigated here after annealing in vacuum up to 870 °C. The annealed samples showed transformation of α-(Cr,Zr)2O3 and amorphous ZrOx-rich areas into tetragonal ZrO2 and bcc-Cr. The instability of the α-(Cr,Zr)2O3 is surprising and possibly related to the annealing being done under vacuum, facilitating the loss of oxygen. Further in situ synchrotron XRD annealing studies on the α-Cr0.28Zr0.10O0.61 coating in air and in vacuum showed increased stability for the air annealed sample up to at least 975 °C, accompanied with a slight increase in ex-situ measured nanohardness. The onset temperature for formation of tetragonal ZrO2 was similar to that for isothermally vacuum annealing. The synchrotron-vacuum annealed coating again decomposed into bcc-Cr and t-ZrO2, with an addition of monoclinic–ZrO2 due to grain growth. The stabilization of the room temperature metastable tetragonal ZrO2 phase, due to surface energy effects present with small grains sizes, may prove to be useful for metal cutting applications. The observed phase segregation of α-(Cr,Zr)2O3 and formation of tetragonal ZrO2 with corresponding increase in hardness for this pseudobinary oxide system also opens up design routes for pseudobinary oxides with tunable microstructural and mechanical properties.

Download or read book Modern Technologies for Creating the Thin film Systems and Coatings written by Nikolay Nikitenkov and published by BoD – Books on Demand. This book was released on 2017-03-08 with total page 446 pages. Available in PDF, EPUB and Kindle. Book excerpt: Development of the thin film and coating technologies (TFCT) made possible the technological revolution in electronics and through it the revolution in IT and communications in the end of the twentieth century. Now, TFCT penetrated in many sectors of human life and industry: biology and medicine; nuclear, fusion, and hydrogen energy; protection against corrosion and hydrogen embrittlement; jet engine; space materials science; and many others. Currently, TFCT along with nanotechnologies is the most promising for the development of almost all industries. The 20 chapters of this book present the achievements of thin-film technology in many areas mentioned above but more than any other in medicine and biology and energy saving and energy efficiency.

Download or read book Reactive Sputter Deposition of Piezoelectric Zinc Oxide Thin Films written by Eugenia Mirica and published by . This book was released on 2002 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Energy Research Abstracts written by and published by . This book was released on 1990 with total page 852 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Research in Progress written by and published by . This book was released on 1983 with total page 644 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Vanadium Dioxide Based Thermochromic Smart Windows written by Yi Long and published by CRC Press. This book was released on 2021-05-27 with total page 416 pages. Available in PDF, EPUB and Kindle. Book excerpt: The usage of building energy accounts for 30–40% of total energy consumption in developed countries, exceeding the amount for industry or transportation. Around 50% energy for building services is contributed by heating, ventilation, and air-conditioning (HVAC) systems. More importantly, both building and HVAC energy consumptions are predicted to increase in the next two decades. Windows are considered as the least energy-efficient components of buildings. Therefore, smart windows are becoming increasingly important as they are capable of reducing HVAC energy usage by tuning the transmitted sunlight in a smart and favoured way: blocking solar irradiation on hot days, while letting it pass through on cold days. Compared with other type of smart windows, thermochromic windows have the unique advantages of cost-effectiveness, rational stimulus, and passive response. This book covers fabrication of vanadium dioxide–based smart windows, discusses various strategies to enhance their performance, and shares perspectives from the top scientists in this particular field.

Download or read book Reduced process temperature of vanadium dioxide films sputtered in reactive O H plasmas written by Ho-chul Joung and published by . This book was released on 1993 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: