Download or read book Processing and Utilization of Wet Flue Gas Desulfurization Material written by and published by . This book was released on 1997 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cooperative Power's Coal Creek Station (CCS) became fully operational in 1981. The two 550-MW units at CCS burn North Dakota lignite. The resulting by-products are fly ash, bottom ash, and wet FGD material. Although disposal of the coal combustion by-products (CCBs) was included in the original site plant at CCS, even early on, consideration was given to utilization of the fly ash as a mineral admixture for concrete and as a partial sorbent replacement for the wet scrubbing system. CCS fly ash has been successfully marketed into North Dakota, Minnesota, and the surrounding region as a construction material that is environmentally benign, highly consistent, and an excellent performer in numerous construction applications. Attempts to use CCS fly ash as part of the scrubbing medium in the wet scrubbing system at the site were not as successful as first hoped, primarily due to the abrasive nature of the fly ash. Currently, CCS scrubbers use lime as the scrubbing medium for SO2 removal. CCS's efforts to market its fly ash have been successful, so with increased awareness of the economic advantages of by-product utilization, the favorable US Environmental Protection Agency (EPA) regulatory determination that CCBs are not hazardous, and the improved understanding of potential local and regional markets, Cooperative Power has taken additional steps to investigate the processing and utilization of its wet FGD material. These steps are discussed.
Download or read book Flue Gas Desulfurization and Industrial Minerals written by M. Michael Miller and published by . This book was released on 1993 with total page 720 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contains 4,101 references on FGD [Flue Gas Desulfurization] ... primarily from 1982 through June 1993. Complements the "Flue Gas Desulfurization and Denitrification" bibliography published by the U.S. Dept. of Energy in Jan. 1985. References were located on the Energy, Science and Technology, Pollution Abstracts, and Environmental Bibliography databases. Primarily covers FGD and the use of industrial minerals in the desulfurization process or in by-product utilization and disposal. Emphasizes post-combustion removal of sulfur dioxide through processes such as in-duct injection and wet and dry scrubbing.
Download or read book Dry Scrubbing Technologies for Flue Gas Desulfurization written by Barbara Toole-O'Neil and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 895 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dry sulfurization processes offer the significant advantages of low capital and low operating costs when compared to wet desulfurization. They hold great potential for the economical reduction of sulfur emissions from power utilities that use high-sulfur coal. Dry Scrubbing Technologies for Flue Gas Desulfurization represents a body of research that was sponsored by the State of Ohio's Coal Development Office for the development of technologies that use coal in an economic, environmentally-sound manner. One of the project's major goals was the development of dry, calcium-based sorption processes for removing sulfur dioxide from the combustion gases produced by high-sulfur coal. Dry Scrubbing Technologies for Flue Gas Desulfurization highlights a number of fundamental research findings that have had a significant and lasting impact in terms of scientific understanding. For example, the experimental investigation of the upper-furnace sulfur capture obtained time-resolved kinetic data in less than 100 millisecond time-scales for the first time ever, thereby revealing the true nature of the ultra-fast and overlapping phenomena. This was accomplished through the development of a unique entrained flow reactor system. The authors also identify a number of important areas for future research, including reaction mechanisms, sorbent material, transport effects, modeling, and process development. Dry Scrubbing Technologies for Flue Gas Desulfurization will appeal to both chemical and environmental engineers who examine different ways touse coal in a more environmentally benign manner. It will make an essential reference for air pollution control researchers from coal, lime, cement, and utility industries; for government policy-makers and environmental regulatory agencies; and for those who teach graduate courses in environmental issues, pollution control technologies, and environmental policy.
Download or read book Application and Development Trend of Flue Gas Desulfurization FGD Process written by Rehan Jamil and published by . This book was released on 2014-03-04 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: Scholarly Research Paper from the year 2013 in the subject Engineering - Chemical Engineering, grade: Master, course: Engineering, language: English, abstract: In 1927, the limestone desulfurization process was first applied in the Barthes and Bansside Power Plants (total 120MW) beside the Thames River in UK to protect high-rise building in London. Up to now, over 10 desulfurization processes have been launched and applied. Based on the desulfurizing agent being used, there include calcium process (limestone/lime), ammonia process, magnesium process, sodium process, alkali alumina process, copper oxide/zinc process, active carbon process, ammonium dihydrogen phosphate process, etc. The calcium process is commercially available and widely used in the world, i.e. more than 90%. Flue gas desulfurization processes, survey made by the coal research institute under the International Energy Agency shows that the wet-process desulfurization accounts for 85% of total installed capacity of flue gas desulfurization units across the world. The wet-process desulfurization is mainly applied in countries, like Japan (98%), USA (92%), Germany (90%), etc. The limestone-gypsum wet desulfurization process, the most mature technology, the most applications, the most reliable operation in the world, may have rate of desulfurization of more than 90%. Currently, the flue gas desulfurization technology used at thermal power plants at home and abroad tends to be higher rate of desulfurization, bigger installed capacity, more advanced technology, lower investment, less land acquisition, lower operation cost, higher level of automation, more excellent reliability, etc. This paper briefs current situations and trends of flue gas desulfurization technology also append short descript of different type of FDG and their category.
Download or read book Profiles in Flue Gas Desulfurization written by Richard R. Lunt and published by John Wiley & Sons. This book was released on 2010-08-27 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: As the need to control process emissions has increased, so have the number of FGD treatment and control strategies. The effectiveness of these treatments vary greatly, depending the types and levels of the materials, as well as the size of the facility. Profiles in Flue Gas Desulfurization will help engineers and managers identify the technologies that best fit their plant and/or processes. It’s a quick and easy reference to all “tail-end” SO2 control processes currently in commercial use or “on the brink,” providing an effective “snapshot” of where this technology stands in industry today. The technologies are divided into waste producing processes, where the end product is a “clean waste,” and byproduct processes, where the end product has market value. Each technology profile includes a schematic depicting its major equipment components and arrangement, laid out side-by-side with descriptive text on how the process works, where and how it is currently being utilized, its operational requirements, advantages and limitations for typical applications, and a brief list of principal suppliers.
Download or read book Nitrogen the Confer N s written by K. van der Hoek and published by Elsevier. This book was released on 2012-12-02 with total page 813 pages. Available in PDF, EPUB and Kindle. Book excerpt: The First International Nitrogen Conference provided an opportunity for researchers and decision-makers to exchange information on environmental pollution by nitrogen compounds on three scales: global, continental/regional and local. The main topics were air, ground water and surface water pollution; emission sources, atmospheric chemistry, deposition processes and effects; disturbance of nitrogen cycles, critical loads and levels; assessments, policy development and evaluation; target groups and abatement techniques; and new approaches leading to an integrated abatement strategy.The peer-reviewed papers from the Conference presented in this volume will provide readers with a comprehensive review of the transport, deposition and impact on ecosystems of nitrogen.
Download or read book Coal Combustion Products CCPs written by Tom Robl and published by Woodhead Publishing. This book was released on 2017-05-03 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Coal Combustion Products (CCPs): Their Nature, Utilization and Beneficiation is a valuable resource for engineers and scientists from the coal, cement, concrete, and construction industries seeking an in-depth guide to the characteristics, utilization, beneficiation, and environmental impacts of coal combustion by-products. Researchers in universities working in this area will also find much to expand their knowledge. The book provides a detailed overview of the different waste materials produced during power generation from coal, exploring their nature, beneficiation techniques, applications, and environmental impacts. Strong focus is placed on coal fly ash, bottom ash, and flue gas desulfurization materials, and their employment in cement, concrete, gypsum products, aggregates, road construction, geotechnics, and agriculture, among other products and industries. Part 1 focuses on the nature of coal ashes, with chapters on their origin, generation, and storage, both in ponds and landfill. The coal combustion by-products produced as a result of clean coal technologies are the focus of the final chapter in the section. The next group of chapters in Part 2 considers the utilization of different waste materials, including the key products coal fly ash, bottom ash, and flue gas desulfurization materials. This is followed by a contribution reviewing the latest research into innovative and advanced uses for coal ash. After an introduction to ash quality problems and quality monitoring, Part 3 concentrates on the essential area of by-product beneficiation techniques, in other words how to maximize the quality of materials for the end user. Topics covered include separation methods, thermal processing, and chemical passivation. The final section of the book addresses environmental issues, including the use of coal combustion by-products in green construction materials and the essential health and safety considerations associated with their use.
Download or read book State of the art Review of Materials related Problems in Flue Gas Desulfurization Systems written by and published by . This book was released on 1980 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This report characterizes the chemical and mechanical environments to which the structural components used in flue-gas desulfurization (FGD) are exposed. It summarizes the necessary background information pertinent to various FGD processes currently in use, with particular emphasis on lime/limestone scrubbing technology, so that the materials problems and processing variables encountered in FGD systems can be better defined and appreciated. The report also describes the materials currently used and their performance to date in existing wet scrubbers. There is little doubt that with more extensive use of coal and flue-gas scrubbers by utilities and other segments of private industry, a better understanding of the material failure mechanisms, performance limitations, and potential problem areas is required for the design of more reliable and cost-effective FGD systems. To meet the above objectives, a materials evaluation program is proposed. The important experimental variables and the number of tests required to evaluate a given material are discussed. 55 references, 9 figures, 6 tables.
Download or read book Technology Assessment Report for Industrial Boiler Applications written by J. Buroff and published by . This book was released on 1979 with total page 762 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Status of Flue Gas Desulfurization Applications in the United States written by United States. Federal Power Commission and published by . This book was released on 1977 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Centrifugal Separations in Biotechnology written by Wallace Woon-Fong Leung and published by Butterworth-Heinemann. This book was released on 2020-03-13 with total page 503 pages. Available in PDF, EPUB and Kindle. Book excerpt: Centrifugal Separations in Biotechnology, Second Edition, is the only book on the market devoted to centrifugal separation in biotechnology. Key topics covered include a full introduction to centrifugation, sedimentation and separation; detailed coverage of centrifuge types, including batch and semi-batch centrifuges, disk-stack and tubular decanter centrifuges; methods for increasing solids concentration; laboratory and pilot testing of centrifuges; selection and sizing centrifuges; scale-up of equipment, performance prediction and analysis of test results using numerical simulation. Centrifugal Separations in Biotechnology, Second Edition, provides guidance on troubleshooting and optimizing centrifuges, and then goes on to explore the commercial applications of centrifuges in biotechnology. It gives detailed process information and data to assist in the development of particular processes from existing systems. It is of value to professionals in the chemical, bioprocess, and biotech sectors, and all those concerned with bioseparation, bioprocessing, unit-operations and process engineering. - Provides a comprehensive guide to centrifuges, their optimal development, and their operation in the biotechnology industry - Updated throughout based on developments in industrial applications and advances in our understanding of centrifugal separations in biotechnology - Discusses applications for the separation of proteins, DNA, mitochondria, ribosomes, lysosomes and other cellular elements - Includes new sections on use of optimal polymer dosage in waste treatment, new centrifuge designs for applications in algae processing, biopharma, and more
Download or read book Phosphorus in Agriculture 100 Zero written by Ewald Schnug and published by Springer. This book was released on 2016-06-14 with total page 357 pages. Available in PDF, EPUB and Kindle. Book excerpt: The title ‘Phosphorus in Agriculture: 100 % Zero’ is synonymous for make-or-break. And it stands up to the promise. This book sends an important message as it delivers background information, intrinsic hypotheses, validation approaches and legal frameworks, all for balanced phosphorus fertilization in agriculture. This implies firstly that the phosphorus requirement of crop is fully satisfied by applying exclusively fertilizers which contain the nutrient in completely available form. Secondly, environmental demands through eutrophication and hazardous contaminants must not be compromised. The book identifies equally knowledge gaps and deficits in the transformation and implementation of research into practice. Bottom line is that research delivers the tools for a sustainable phosphorus management while legal frameworks are insufficient.
Download or read book Coal written by National Research Council and published by National Academies Press. This book was released on 2007-12-21 with total page 183 pages. Available in PDF, EPUB and Kindle. Book excerpt: Coal will continue to provide a major portion of energy requirements in the United States for at least the next several decades. It is imperative that accurate information describing the amount, location, and quality of the coal resources and reserves be available to fulfill energy needs. It is also important that the United States extract its coal resources efficiently, safely, and in an environmentally responsible manner. A renewed focus on federal support for coal-related research, coordinated across agencies and with the active participation of the states and industrial sector, is a critical element for each of these requirements. Coal focuses on the research and development needs and priorities in the areas of coal resource and reserve assessments, coal mining and processing, transportation of coal and coal products, and coal utilization.
Download or read book Combustion Ash Residue Management written by Richard W. Goodwin and published by William Andrew. This book was released on 2013-12-05 with total page 147 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion Ash and Residue Management assists owners and operators of Coal-fired and Resource Recovery Power Plants. By applying the principles and reviewing the case studies examples described within this book, accidents and upsets can be avoided and regulatory permitting can be achieved – reducing costs. This unique book is an essential reference for anybody responsible for disposal or utilization of combustion residues. It reflects over 30 years of engineering practice, applying the principles of concrete chemistry and civil engineering/soil mechanics as confirmed by field data. Dr. Richard Goodwin assesses the composition and environmental impact of combustion residues, and provides not only best practices for safe disposal, but also a blueprint for effective reuse, including applications like structural fill, grout, and capping material. Case studies and cost information for ash disposal options are included, in addition to the lessons learned by high-profile failures, such as the TVA Kingston fossil plant coal fly ash slurry spill in 2008. It also applies engineering principles to discuss how to avoid future upsets, including better operator training and monitoring methods. - A comprehensive update to reflect changes in legislation and practice, including new material on the safe disposal or beneficial use of coal ash - A straightforward engineering approach, providing practical guidance and field data - Written by an established expert in the field
Download or read book The Problems of Sulphur written by Sam Stuart and published by Butterworth-Heinemann. This book was released on 2013-10-22 with total page 366 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Problems of Sulphur discusses all aspects of the problems associated with sulfur in coal. The book is divided into three parts. Part 1 addresses the forms of sulfur in coal and evaluates processes directed at the chemical removal of sulphur. Part 2 expands on this to look at alternative means of removing sulfur both physically and biologically, sulfur removal during the combustion of coal and flue gas desulfurization processes. Part 3 looks at the role of sulphates in the atmosphere from the points of view of their formation, transport and deposition and of their effects on health, materials and the atmosphere. The book will be of value to engineers, environmentalists, and chemists.
Download or read book Proceedings written by and published by . This book was released on 1976 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Research Technology Transporter written by and published by . This book was released on 1998 with total page 10 pages. Available in PDF, EPUB and Kindle. Book excerpt:
