Download or read book Potential of Water Injection for Gasoline Engines by Means of a 3D CFD Virtual Test Bench written by Antonino Vacca and published by Springer Nature. This book was released on 2020-12-15 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: Water injection is one of the most promising technologies to improve the engine combustion efficiency, by mitigating knock occurrences and controlling exhaust gas temperature before turbine. As result, the engine can operate at stoichiometric conditions over the whole engine map, even during the more power-demanding RDE cycles. Antonino Vacca presents a methodology to study and optimize the effect of water injection for gasoline engines by investigating different engine layouts and injection strategies through the set-up of a 3D-CFD virtual test bench. He investigates indirect and direct water injection strategies to increase the engine knock limit and to reduce exhaust gas temperature for several operating points.

Download or read book Investigation of Innovative Water Injection Strategies for Gasoline Engines by Means of a 3D CFD Virtual Engine Test Bench written by Edoardo Rossi and published by Springer Nature. This book was released on 2024 with total page 185 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the investigation of innovative engine technologies that can improve the efficiency of internal combustion engines and reduce their environmental impact. In particular, water injection is examined as a means of improving engine behavior. The possible combination of water injection with renewable fuels is also a topic of the book. The results of this experimental and numerical research show positive results that can be used for further research and development of engines. Content 3D-CFD Simulation Environment: the Virtual Engine Test Bench Experimental Spray Analysis and 3D-CFD Injection Model Calibration Applicability of Water Injection in Combination with an eFuel Water-in-Fuel Emulsions at the Virtual Engine Test Bench Target Groups Students and researchers in the field of automotive engineering, esp. engine technology Engineers in the automotive industry About the Author Edoardo Rossi is a project manager in the virtual engine development department at the FKFS, where he did his PhD. He works on innovative solutions for future powertrain technologies for motor vehicles. .

Download or read book Potential of Water Injection for Gasoline Engines by Means of a 3D CFD Virtual Test Bench written by Antonino Vacca and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Water injection is one of the most promising technologies to improve the engine combustion efficiency, by mitigating knock occurrences and controlling exhaust gas temperature before turbine. As result, the engine can operate at stoichiometric conditions over the whole engine map, even during the more power-demanding RDE cycles. Antonino Vacca presents a methodology to study and optimize the effect of water injection for gasoline engines by investigating different engine layouts and injection strategies through the set-up of a 3D-CFD virtual test bench. He investigates indirect and direct water injection strategies to increase the engine knock limit and to reduce exhaust gas temperature for several operating points. Contents Influence of Water Vapour on Flame Speed and Auto-Ignition Optimization of the Water Injector Targeting Mixture Formation Induced by Water Injection Water Injection in Combination with Miller Cycle Target Groups Researchers and students in the field of automotive engineering Automotive engineers About the Author Antonino Vacca obtained a PhD at the research Institute of Automotive Engineering (IFS), University of Stuttgart and he is currently project leader at FKFS (Stuttgart, Germany) responsible for the development of innovative combustion concepts for gasoline and gas engines.

Download or read book Emission Reduction with an Alternative Diesel Combustion Process written by Marvin Sascha Wahl and published by Springer Nature. This book was released on 2023-07-29 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: Marvin Sascha Wahl presents the possibilities for optimising diesel engine combustion. In the advanced process of partially premixed diesel combustion, nitrogen oxide and soot emissions can be minimised at the same time. A new feature is the possibility of applying this strategy up to 2000 revolutions and 10 bar indicated mean pressure. In this work, various effective parameters are also compared and correlated with each other. A final comparison with conventional diesel combustion shows the advantages and disadvantages and evaluates them.

Download or read book A Simulative Approach to Predict Energy Consumption of Future Powertrain Configurations for the Year 2040 written by Tobias Stoll and published by Springer Nature. This book was released on 2023-07-29 with total page 245 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with the simulative prediction of efficiency and CO2-emissions of future powertrain systems for the year 2040. For this purpose, a suitable simulation environment is first created. This is followed by a technology extrapolation of all relevant powertrain systems, for example: combustion engines, electric drives, fuel cells as well as all relevant additional components. These components are then used to build 57 vehicle variants for the simulation. Finally, extensive simulations of the vehicle variants are carried out, evaluated and compared. Comprehensive tables of results are available for all simulated vehicle variants. The evaluations are of interest to anyone concerned with energy consumption and CO2-emissions of future vehicles.

Download or read book Annual Index abstracts of SAE Technical Papers written by and published by . This book was released on 2007 with total page 1218 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Two Stroke Cycle Engine written by JohnB. Heywood and published by Routledge. This book was released on 2017-11-01 with total page 425 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses the two-stroke cycle internal combustion engine, used in compact, lightweight form in everything from motorcycles to chainsaws to outboard motors, and in large sizes for marine propulsion and power generation. It first provides an overview of the principles, characteristics, applications, and history of the two-stroke cycle engine, followed by descriptions and evaluations of various types of models that have been developed to predict aspects of two-stroke engine operation.

Download or read book An Innovative 3D CFD Approach towards Virtual Development of Internal Combustion Engines written by Marco Chiodi and published by Springer Science & Business Media. This book was released on 2011-03-07 with total page 275 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the engine development process, simulation and predictive programs have continuously gained in reliance. Due to the complexity of future internal combustion engines the application of simulation programs towards a reliable “virtual engine development” is a need that represents one of the greatest challenges. Marco Chiodi presents an innovative 3D-CFD-tool, exclusively dedicated and optimized for the simulation of internal combustion engines. Thanks to improved or newly developed 3D-CFD-models for the description of engine processes, this tool ensures an efficient and reliable calculation also by using coarse 3D-CFD-meshes. Based on this approach the CPU-time can be reduced up to a factor 100 in comparison to traditional 3D-CFD-simulations. In addition an integrated and automatic “evaluation tool” establishes a comprehensive analysis of the relevant engine parameters. Due to the capability of a reliable “virtual development” of full-engines, this fast response 3D-CFD-tool makes a major contribution to the engine development process. Südwestmetall-Förderpreis 2010

Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1994 with total page 1036 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of Diesel Engines written by Klaus Mollenhauer and published by Springer Science & Business Media. This book was released on 2010-06-22 with total page 632 pages. Available in PDF, EPUB and Kindle. Book excerpt: This machine is destined to completely revolutionize cylinder diesel engine up through large low speed t- engine engineering and replace everything that exists. stroke diesel engines. An appendix lists the most (From Rudolf Diesel’s letter of October 2, 1892 to the important standards and regulations for diesel engines. publisher Julius Springer. ) Further development of diesel engines as economiz- Although Diesel’s stated goal has never been fully ing, clean, powerful and convenient drives for road and achievable of course, the diesel engine indeed revolu- nonroad use has proceeded quite dynamically in the tionized drive systems. This handbook documents the last twenty years in particular. In light of limited oil current state of diesel engine engineering and technol- reserves and the discussion of predicted climate ogy. The impetus to publish a Handbook of Diesel change, development work continues to concentrate Engines grew out of ruminations on Rudolf Diesel’s on reducing fuel consumption and utilizing alternative transformation of his idea for a rational heat engine fuels while keeping exhaust as clean as possible as well into reality more than 100 years ago. Once the patent as further increasing diesel engine power density and was filed in 1892 and work on his engine commenced enhancing operating performance.

Download or read book Combustion Engines Development written by Günter P. Merker and published by Springer Science & Business Media. This book was released on 2011-09-24 with total page 660 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion Engines Development nowadays is based on simulation, not only of the transient reaction of vehicles or of the complete driveshaft, but also of the highly unsteady processes in the carburation process and the combustion chamber of an engine. Different physical and chemical approaches are described to show the potentials and limits of the models used for simulation.

Download or read book Mixture Formation in Internal Combustion Engines written by Carsten Baumgarten and published by Springer Science & Business Media. This book was released on 2006-09-28 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: A systematic control of mixture formation with modern high-pressure injection systems enables us to achieve considerable improvements of the combustion pr- ess in terms of reduced fuel consumption and engine-out raw emissions. However, because of the growing number of free parameters due to more flexible injection systems, variable valve trains, the application of different combustion concepts within different regions of the engine map, etc., the prediction of spray and m- ture formation becomes increasingly complex. For this reason, the optimization of the in-cylinder processes using 3D computational fluid dynamics (CFD) becomes increasingly important. In these CFD codes, the detailed modeling of spray and mixture formation is a prerequisite for the correct calculation of the subsequent processes like ignition, combustion and formation of emissions. Although such simulation tools can be viewed as standard tools today, the predictive quality of the sub-models is c- stantly enhanced by a more accurate and detailed modeling of the relevant pr- esses, and by the inclusion of new important mechanisms and effects that come along with the development of new injection systems and have not been cons- ered so far. In this book the most widely used mathematical models for the simulation of spray and mixture formation in 3D CFD calculations are described and discussed. In order to give the reader an introduction into the complex processes, the book starts with a description of the fundamental mechanisms and categories of fuel - jection, spray break-up, and mixture formation in internal combustion engines.

Download or read book Vehicle Propulsion Systems written by Lino Guzzella and published by Springer Science & Business Media. This book was released on 2007-09-21 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: The authors of this text have written a comprehensive introduction to the modeling and optimization problems encountered when designing new propulsion systems for passenger cars. It is intended for persons interested in the analysis and optimization of vehicle propulsion systems. Its focus is on the control-oriented mathematical description of the physical processes and on the model-based optimization of the system structure and of the supervisory control algorithms.

Download or read book Charging the Internal Combustion Engine written by Hermann Hiereth and published by Springer Science & Business Media. This book was released on 2007-11-04 with total page 283 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers all aspects of supercharging internal combustion engines. It details charging systems and components, the theoretical basic relations between engines and charging systems, as well as layout and evaluation criteria for best interaction. Coverage also describes recent experiences in design and development of supercharging systems, improved graphical presentations, and most advanced calculation and simulation tools.

Download or read book Handbook of Air Pollution from Internal Combustion Engines written by Eran Sher and published by Academic Press. This book was released on 1998-03-20 with total page 689 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is an important and valuable source for engineers and researchers in the area of internal combustion engines pollution control. It provides an excellent updated review of available knowledge in this field and furnishes essential and useful information on air pollution constituents, mechanisms of formation, control technologies, effects of engine design, effects of operation conditions, and effects of fuel formulation and additives. The text is rich in explanatory diagrams, figures and tables, and includes a considerable number of references. - An important resource for engineers and researchers in the area of internal combustion engines and pollution control - Presents and excellent updated review of the available knowledge in this area - Written by 23 experts - Provides over 700 references and more than 500 explanatory diagrams, figures and tables

Download or read book Ignition Systems for Gasoline Engines written by Michael Günther and published by Springer. This book was released on 2016-11-18 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: The volume includes selected and reviewed papers from the 3rd Conference on Ignition Systems for Gasoline Engines in Berlin in November 2016. Experts from industry and universities discuss in their papers the challenges to ignition systems in providing reliable, precise ignition in the light of a wide spread in mixture quality, high exhaust gas recirculation rates and high cylinder pressures. Classic spark plug ignition as well as alternative ignition systems are assessed, the ignition system being one of the key technologies to further optimizing the gasoline engine.

Download or read book Systems Engineering for Automotive Powertrain Development written by Hannes Hick and published by Springer. This book was released on 2021-02-25 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: For the last century, the automotive industry has been dominated by internal combustion engines. Their flexibility of application, driving range, performance and sporty characteristics has resulted in several generations of this technology and has formed generations of engineers. But that is not the end of the story. Stricter legislation and increased environmental awareness have resulted in the development of new powertrain technologies in addition and parallel to the highly optimized internal combustion engine. Hybrid powertrains systems, pure battery electric systems and fuel cell systems, in conjunction with a diverse range of applications, have increased the spectrum of powertrain technologies. Furthermore, automated driving together with intelligent and highly connected systems are changing the way to get from A to B. Not only is the interaction of all these new technologies challenging, but also several different disciplines have to collaborate intensively in order for new powertrain systems to be successfully developed. These new technologies and the resulting challenges lead to an increase in system complexity. Approaches such as systems engineering are necessary to manage this complexity. To show how systems engineering manages the increasing complexity of modern powertrain systems, by providing processes, methods, organizational aspects and tools, this book has been structured into five parts. Starting with Challenges for Powertrain Development, which describes automotive-related challenges at different levels of the system hierarchy and from different point of views. The book then continues with the core part, Systems Engineering, in which all the basics of systems engineering, model-based systems engineering, and their related processes, methods, tools, and organizational matters are described. A special focus is placed on important standards and the human factor. The third part, Automotive Powertrain Systems Engineering Approach, puts the fundamentals of systems engineering into practice by adding the automotive context. This part focuses on system development and also considers the interactions to hardware and software development. Several approaches and methods are presented based on systems engineering philosophy. Part four, Powertrain Development Case Studies, adds the practical point of view by providing a range of case studies on powertrain system level and on powertrain element level and discusses the development of hybrid powertrain, internal combustion engines, e-drives, transmissions, batteries and fuel cell systems. Two case studies on a vehicle level are also presented. The final part, Outlook, considers the development of systems engineering itself with particular focus on information communication technologies. Even though this book covers systems engineering from an automotive perspective, many of the challenges, fundamental principles, conclusions and outlooks can be applied to other domains too. Therefore, this book is not only relevant for automotive engineers and students, but also for specialists in scientific and industrial positions in other domains and anyone who has to cope with the challenge of successfully developing complex systems with a large number of collaborating disciplines.