Download or read book Plasma Properties Deposition and Etching written by J.J. Pouch and published by Trans Tech Publications Ltd. This book was released on 1993-10-28 with total page 749 pages. Available in PDF, EPUB and Kindle. Book excerpt: Containing 42 invited papers, this fine book covers a broad range of subjects on plasmas and applications. In the first section, plasma properties and methods used to characterize the plasma are addressed. Many of these papers also cover deposition or etching of particular materials. The second part focuses on the application of various plasma techniques used to deposit thin films, and on the resulting film properties. Finally, the application of plasma etching to the fabrication of silicon-based circuits, plasma etching of III-V compound semiconductors and other processing applications are discussed in the third and last section.
Download or read book Plasma Sources for Thin Film Deposition and Etching written by Maurice H. Francombe and published by Academic Press. This book was released on 2013-10-22 with total page 343 pages. Available in PDF, EPUB and Kindle. Book excerpt: This latest volume of the well-known Physics of Thin Films Series includes four chapters that discuss high-density plasma sources for materials processing, electron cyclotron resonance and its uses, unbalancedmagnetron sputtering, and particle formation in thin film processing plasma. Chapter One develops a unified framework from which all "high-efficiency" sources may be viewed and compared; outlines key elements of source design affecting processing results; and highlights areas where additional research and development are needed Chapter Two reviews and analyzes the main types of electron cyclotron resonance (ECR) plasma sources suitable for ECR PACVD of thin films, mainly ECR sources using magnet coils Chapter Three examines the benefits and limitations of the new technique, unbalanced magnetron sputtering (UBM), along with the motivation for its development, the basic principles of its operation and commercial applications, and some speculations regarding the future of UBM technology Chapter Four describes general phenomena observed in connection with particle formation in thin film processing plasmas; discusses particles in PECVD plasmas, sputtering plasmas, and RIE plasmas; presents an overview of the theoretical modeling of various aspects of particles in processing plasmas; examines issues of equipment design affecting particle formation; and concludes with remarks about the implications of this work for the control of process-induced particle contamination
Download or read book Plasma Deposition Treatment and Etching of Polymers written by Riccardo d'Agostino and published by Elsevier. This book was released on 2012-12-02 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: Plasma Deposition, Treatment, and Etching of Polymers takes a broad look at the basic principles, the chemical processes, and the diagnostic procedures in the interaction of plasmas with polymer surfaces. This recent technology has yielded a large class of new materials offering many applications, including their use as coatings for chemical fibers and films. Additional applications include uses for the passivation of metals, the surface hardening of tools, increased biocompatibility of biomedical materials, chemical and physical sensors, and a variety of micro- and optoelectronic devices. Appeals to a broad range of industries from microelectronics to space technology Discusses a wide array of new uses for plasma polymers Provides a tutorial introduction to the field Surveys various classes of plasma polymers, their chemical and morphological properties, effects of plasma process parameters on the growth and structure of these synthetic materials, and techniques for characterization Interests scientists, engineers, and students alike
Download or read book Handbook of Plasma Processing Technology written by Stephen M. Rossnagel and published by William Andrew. This book was released on 1990 with total page 523 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a comprehensive overview of the technology of plasma-based processing, written by an outstanding group of 29 contributors.
Download or read book Plasma Processing written by R. G. Frieser and published by . This book was released on 1981 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Plasma Technology written by M. Capitelli and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present book contains the proceedings of the workshop "Plasma Technology and Applications" which was held at 11 Ciocco (Lucca-Italy) during 5-6 July 1991. The workshop was organized just before ICPIG XX to emphasize the role of plasma physics and plasma chemistry in different fields of technology. Topics cover different applications such as lamps, plasma treatment of materials (etching, deposition, nitriding), plasma sources (microwave excitation, negative ion sources) and plasma destruction of pollutants. Several chapters deal with basic concepts in plasma physics, non equilibrium plasma modeling and plasma diagnostics as well as with laser interaction with solid targets. The authors gratefully acknowledge the financial support provided by university of Bari (Italy) and by CNR (Centro di Studio per la Chimica dei Plasmi, Istituto di Fisica Atomica e Molecolare (IFAM) and Progetto Finalizzato Materiali Speciali per Tecnologie Avanzate) as well as the sponsorship of ENEA. M. Capitelli C. Gorse v CONTENTS Plasmas in nature, laboratory and technology 1 A.M. Ignatov and A.A. Rukhadze Laser diagnostics of plasmas 11 L. Pyatnitsky Probe diagnostics of plasmas 27 G. Dilecce Theory, properties and applications of non equilibrium plasmas created by external energy sources 45 E. Son Non-Equilibrium plasma modeling 59 M. Capitel1i, R. Celiberto, G. Capriati, C. Gorse and S. Longo Gas discharge lamps 81 M. Koedam Plasma etching processes and diagnostics 93 R. d'Agostino and F. Fracassi Plasma deposition: processes and diagnostics 109 A
Download or read book Handbook of Advanced Plasma Processing Techniques written by R.J. Shul and published by Springer Science & Business Media. This book was released on 2011-06-28 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: Pattern transfer by dry etching and plasma-enhanced chemical vapor de position are two of the cornerstone techniques for modern integrated cir cuit fabrication. The success of these methods has also sparked interest in their application to other techniques, such as surface-micromachined sen sors, read/write heads for data storage and magnetic random access memory (MRAM). The extremely complex chemistry and physics of plasmas and their interactions with the exposed surfaces of semiconductors and other materi als is often overlooked at the manufacturing stage. In this case, the process is optimized by an informed "trial-and-error" approach which relies heavily on design-of-experiment techniques and the intuition of the process engineer. The need for regular cleaning of plasma reactors to remove built-up reaction or precursor gas products adds an extra degree of complexity because the interaction of the reactive species in the plasma with the reactor walls can also have a strong effect on the number of these species available for etching or deposition. Since the microelectronics industry depends on having high process yields at each step of the fabrication process, it is imperative that a full understanding of plasma etching and deposition techniques be achieved.
Download or read book Application of Particle and Laser Beams in Materials Technology written by P. Misaelides and published by Springer Science & Business Media. This book was released on 1995-01-31 with total page 702 pages. Available in PDF, EPUB and Kindle. Book excerpt: The development of advanced materials with preselected properties is one of the main goals of materials research. Of especial interest are electronics, high-temperature and superhard materials for various applications, as well as alloys with improved wear, corrosion and mechanical resistance properties. The technical challenge connected with the production of these materials is not only associated with the development of new specialised preparation techniques but also with quality control. The energetic charged particle, electron and photon beams offer the possibility of modifying the properties of the near-surface regions of materials without seriously affecting their bulk, and provide unique analytical tools for testing their quality. Application of Particle and Laser Beams in Materials Technology provides an overview of this rapidly expanding field. Fundamental aspects concerning the interactions and collisions on atomic, nuclear and solid state scale are presented in a didactic way, along with the application of a variety of techniques for the solution of problems ranging from the development of electronics materials to corrosion research and from archaeometry to environmental protection. The book is divided into six thematic units: Fundamentals, Surface Analysis Techniques, Laser Beams in Materials Technology, Accelerator-Based Techniques in Materials Technology, Materials Modification and Synchrotron Radiation.
Download or read book Plasma Processing of Materials written by National Research Council and published by National Academies Press. This book was released on 1991-02-01 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: Plasma processing of materials is a critical technology to several of the largest manufacturing industries in the worldâ€"electronics, aerospace, automotive, steel, biomedical, and toxic waste management. This book describes the relationship between plasma processes and the many industrial applications, examines in detail plasma processing in the electronics industry, highlights the scientific foundation underlying this technology, and discusses education issues in this multidisciplinary field. The committee recommends a coordinated, focused, and well-funded research program in this area that involves the university, federal laboratory, and industrial sectors of the community. It also points out that because plasma processing is an integral part of the infrastructure of so many American industries, it is important for both the economy and the national security that America maintain a strong leadership role in this technology.
Download or read book Plasma Etching written by M. Sugawara and published by OUP Oxford. This book was released on 1998-05-28 with total page 362 pages. Available in PDF, EPUB and Kindle. Book excerpt: The focus of this book is the remarkable advances in understanding of low pressure RF (radio frequency) glow discharges. A basic analytical theory and plasma physics are explained. Plasma diagnostics are also covered before the practicalities of etcher use are explored.
Download or read book Plasma Surface Interactions and Processing of Materials written by O. Auciello and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 548 pages. Available in PDF, EPUB and Kindle. Book excerpt: An understanding of the processes involved in the basic and applied physics and chemistry of the interaction of plasmas with materials is vital to the evolution of technologies such as those relevant to microelectronics, fusion and space. The subjects dealt with in the book include: the physics and chemistry of plasmas, plasma diagnostics, physical sputtering and chemical etching, plasma assisted deposition of thin films, ion and electron bombardment, and plasma processing of inorganic and polymeric materials. The book represents a concentration of a substantial amount of knowledge acquired in this area - knowledge which was hitherto widely scattered throughout the literature - and thus establishes a baseline reference work for both established and tyro research workers.
Download or read book Handbook of Physical Vapor Deposition PVD Processing written by D. M. Mattox and published by Cambridge University Press. This book was released on 2014-09-19 with total page 947 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers all aspects of physical vapor deposition (PVD) process technology from the characterizing and preparing the substrate material, through deposition processing and film characterization, to post-deposition processing. The emphasis of the book is on the aspects of the process flow that are critical to economical deposition of films that can meet the required performance specifications. The book covers subjects seldom treated in the literature: substrate characterization, adhesion, cleaning and the processing. The book also covers the widely discussed subjects of vacuum technology and the fundamentals of individual deposition processes. However, the author uniquely relates these topics to the practical issues that arise in PVD processing, such as contamination control and film growth effects, which are also rarely discussed in the literature. In bringing these subjects together in one book, the reader can understand the interrelationship between various aspects of the film deposition processing and the resulting film properties. The author draws upon his long experience with developing PVD processes and troubleshooting the processes in the manufacturing environment, to provide useful hints for not only avoiding problems, but also for solving problems when they arise. He uses actual experiences, called ""war stories"", to emphasize certain points. Special formatting of the text allows a reader who is already knowledgeable in the subject to scan through a section and find discussions that are of particular interest. The author has tried to make the subject index as useful as possible so that the reader can rapidly go to sections of particular interest. Extensive references allow the reader to pursue subjects in greater detail if desired. The book is intended to be both an introduction for those who are new to the field and a valuable resource to those already in the field. The discussion of transferring technology between R&D and manufacturing provided in Appendix 1, will be of special interest to the manager or engineer responsible for moving a PVD product and process from R&D into production. Appendix 2 has an extensive listing of periodical publications and professional societies that relate to PVD processing. The extensive Glossary of Terms and Acronyms provided in Appendix 3 will be of particular use to students and to those not fully conversant with the terminology of PVD processing or with the English language.
Download or read book Handbook of Physical Vapor Deposition PVD Processing written by Donald M. Mattox and published by William Andrew. This book was released on 1998-12-31 with total page 944 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers all aspects of physical vapor deposition (PVD) process technology from the characterizing and preparing the substrate material, through deposition processing and film characterization, to post-deposition processing. The emphasis of the book is on the aspects of the process flow that are critical to economical deposition of films that can meet the required performance specifications. The book covers subjects seldom treated in the literature: substrate characterization, adhesion, cleaning and the processing. The book also covers the widely discussed subjects of vacuum technology and the fundamentals of individual deposition processes. However, the author uniquely relates these topics to the practical issues that arise in PVD processing, such as contamination control and film growth effects, which are also rarely discussed in the literature. In bringing these subjects together in one book, the reader can understand the interrelationship between various aspects of the film deposition processing and the resulting film properties. The author draws upon his long experience with developing PVD processes and troubleshooting the processes in the manufacturing environment, to provide useful hints for not only avoiding problems, but also for solving problems when they arise. He uses actual experiences, called ""war stories"", to emphasize certain points. Special formatting of the text allows a reader who is already knowledgeable in the subject to scan through a section and find discussions that are of particular interest. The author has tried to make the subject index as useful as possible so that the reader can rapidly go to sections of particular interest. Extensive references allow the reader to pursue subjects in greater detail if desired. The book is intended to be both an introduction for those who are new to the field and a valuable resource to those already in the field. The discussion of transferring technology between R&D and manufacturing provided in Appendix 1, will be of special interest to the manager or engineer responsible for moving a PVD product and process from R&D into production. Appendix 2 has an extensive listing of periodical publications and professional societies that relate to PVD processing. The extensive Glossary of Terms and Acronyms provided in Appendix 3 will be of particular use to students and to those not fully conversant with the terminology of PVD processing or with the English language.
Download or read book Film Deposition by Plasma Techniques written by Mitsuharu Konuma and published by Springer. This book was released on 1992-04-30 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt: Properties of thin films depend strongly upon the deposition technique and conditions chosen. In order to achieve the desired film, optimum deposition conditions have to be found by carrying out experiments in a trial-and error fashion with varying parameters. The data obtained on one growth apparatus are often not transferable to another. This is especially true for film deposition processes using a cold plasma because of our poor under standing of the mechanisms. Relatively precise studies have been carried out on the role that physical effects play in film formation such as sputter deposition. However, there are many open questions regarding processes that involve chemical reactions, for example, reactive sputter deposition or plasma enhanced chemical vapor deposition. Much further research is re quired in order to understand the fundamental deposition processes. A sys tematic collection of basic data, some of which may be readily available in other branches of science, for example, reaction cross sections for gases with energetic electrons, is also required. The need for pfasma deposition techniques is felt strongly in industrial applications because these techniques are superior to traditional thin-film deposition techniques in many ways. In fact, plasma deposition techniques have developed rapidly in the semiconductor and electronics industries. Fields of possible application are still expanding. A reliable plasma reactor with an adequate in situ system for monitoring the deposition conditions and film properties must be developed to improve reproducibility and pro ductivity at the industrial level.
Download or read book Cathodic Arcs written by André Anders and published by Springer Science & Business Media. This book was released on 2009-07-30 with total page 555 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cathodic arcs are among the longest studied yet least understood objects in science. Plasma-generating, tiny spots appear on the cathode; they are highly dynamic and hard to control. With an approach emphasizing the fractal character of cathode spots, strongly fluctuating plasma properties are described such as the presence of multiply charged ions that move with supersonic velocity. Richly illustrated, the book also deals with practical issues, such as arc source construction, macroparticle removal, and the synthesis of dense, well adherent coatings. The book spans a bridge from plasma physics to coatings technology based on energetic condensation, appealing to scientists, practitioners and graduate students alike.
Download or read book Plasma Processing of Semiconductors written by P.F. Williams and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 610 pages. Available in PDF, EPUB and Kindle. Book excerpt: Plasma Processing of Semiconductors contains 28 contributions from 18 experts and covers plasma etching, plasma deposition, plasma-surface interactions, numerical modelling, plasma diagnostics, less conventional processing applications of plasmas, and industrial applications. Audience: Coverage ranges from introductory to state of the art, thus the book is suitable for graduate-level students seeking an introduction to the field as well as established workers wishing to broaden or update their knowledge.
Download or read book Plasma Processing for VLSI written by Norman G. Einspruch and published by Academic Press. This book was released on 2014-12-01 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: VLSI Electronics: Microstructure Science, Volume 8: Plasma Processing for VLSI (Very Large Scale Integration) discusses the utilization of plasmas for general semiconductor processing. It also includes expositions on advanced deposition of materials for metallization, lithographic methods that use plasmas as exposure sources and for multiple resist patterning, and device structures made possible by anisotropic etching. This volume is divided into four sections. It begins with the history of plasma processing, a discussion of some of the early developments and trends for VLSI. The second section, Deposition, discusses deposition techniques for VLSI such as sputtering metals for metallization and contacts, plasma-enhanced chemical vapor deposition of metals and suicides, and plasma enhanced chemical vapor deposition of dielectrics. The part on Lithography presents the high-resolution trilayer resist system, pulsed x-ray sources for submicrometer x-ray lithography, and high-intensity deep-UV sources. The last part, Etching, provides methods in etching, like ion-beam etching using reactive gases, low-pressure reactive ion etching, and the uses of inert-gas ion milling. The theory and mechanisms of plasma etching are described and a number of new device structures made possible by anisotropic etching are enumerated as well. Scientists, engineers, researchers, device designers, and systems architects will find the book useful.
