Download or read book Thermal Behavior of Photovoltaic Devices written by Olivier Dupré and published by Springer. This book was released on 2016-12-02 with total page 142 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a comprehensive introduction to the thermal issues in photovoltaics. It also offers an extensive overview of the physics involved and insights into possible thermal optimizations of the different photovoltaic device technologies.In general, temperature negatively affects the efficiency of photovoltaic devices. The first chapter describes the temperature-induced losses in photovoltaic devices and reviews the strategies to overcome them. The second chapter introduces the concept of temperature coefficient, the underlying physics and some guidelines for reducing their negative impacts. Subsequent chapters offer a comprehensive and general thermal model of photovoltaic devices, and review how current and emerging technologies, mainly solar cells but also thermophotovoltaic devices, can benefit from thermal optimizations.Throughout the book, the authors argue that the energy yield of photovoltaic devices can be optimized by taking their thermal behavior and operating conditions into consideration in their design.

Download or read book Physics of the Thermal Behavior of Photovoltaic Devices written by Olivier Dupré and published by . This book was released on 2020 with total page 221 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Ph.D. thesis manuscript reports on a study about the physics of the thermal behavior of photovoltaic (PV) systems. While it is long known that the conversion efficiency of PV devices deteriorates when their temperature increases, a detailed analysis of all the mechanisms involved was not available to date in the literature. Part I of this manuscript gathers and extends the existing works on the topic in order to offer a comprehensive view of the physics involved in the temperature sensitivities of PV systems. First, temperature coefficients, which quantify the temperature dependences, are analyzed in the radiative limit (which is the fundamental limit for PV conversion). Then, the additional loss mechanisms of real PV devices are introduced and their impacts on the temperature coefficients are assessed. The existing theoretical expressions of the temperature coefficients of important solar cell parameters (namely open-circuit voltage, short-circuit current and fill factor) are reviewed. A new formulation of the temperature coefficient of the open-circuit voltage that incorporates the concept of External Radiative Efficiency (ERE) is proposed. The theoretical expressions are compared to experimental results on crystalline silicon cells from measurements made at the University of New South Wales (UNSW, Australia) and from the literature. Using the understanding of the relation between the temperature coefficients and device physics, the special cases of silicon heterojunction cells and cells made from compensated silicon are examined. Because temperature has a critical impact on the performances of PV devices, several studies aimed on the one hand at predicting the temperature of PV modules from their operating conditions and on the other hand at designing inexpensive cooling solutions. The goal of Part II of this manuscript is to propose an original approach to minimize the temperature-induced losses in PV systems. The idea is to include the operating conditions in the optimization of the system parameters in order to maximize the power produced in these conditions rather than in the Standard Test Conditions (STC). These original optimizations are based on a comprehensive thermal model of PV cells that captures all of the physical mechanisms involved in the generation of heat within the cell. Following the presentation of this thermal model, several examples of global optimization (i.e. a thermal criterion is added to the usual optical and electrical ones) are presented. Some of these examples apply to standard solar cells while others demonstrate that this kind of optimization can be applied to other PV systems such as thermophotovoltaic (TPV) converters (solar or near-field TPV). The recent trend of the PV industry towards the creation of products specifically adapted to a given use suggests that these original optimizations that take into account the system operating conditions could be implemented in the near future.

Download or read book The Physics of Solar Cells written by Jenny Nelson and published by World Scientific Publishing Company Incorporated. This book was released on 2003-01-01 with total page 363 pages. Available in PDF, EPUB and Kindle. Book excerpt: An introduction to the physics of the photovoltaic cell. It covers the fundamental principles of semiconductor physics and simple models used to describe solar cell operation. It presents theoretical approaches to efficient solar cell design and examines the main practical types of solar cell

Download or read book Step by Step Design of Large Scale Photovoltaic Power Plants written by Davood Naghaviha and published by John Wiley & Sons. This book was released on 2022-01-12 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: How to design a solar power plant, from start to finish In Step-by-Step Design of Large-Scale Photovoltaic Power Plants, a team of distinguished engineers delivers a comprehensive reference on PV power plants—and their design—for specialists, experts, and academics. Written in three parts, the book covers the detailed theoretical knowledge required to properly design a PV power plant. It goes on to explore the step-by-step requirements for creating a real-world PV power plant, including parts and components design, mathematical formulations and calculations, analyses, evaluations, and planning. The book concludes with a discussion of a sample solar plant design, as well as tips on how to avoid common design mistakes, and how to handle the operation and maintenance of PV power plants. Step-by-Step Design of Large-Scale Photovoltaic Power Plants also includes: Thorough introductions to the basic requirements of design, economic analyses, and investment revenue Comprehensive explorations of the requirements for feasibility study and grid connection study Introducing solar resource, and determining optimum tilt angle and module inter-row spacing Presenting methodology for design of large-scale PV plant, requirements of engineering document, and optimal design algorithm In-depth examinations for selecting PV module, inverter, string, and DC side equipment Practical discussions of system losses, as well as estimation of yearly electrical energy production, capacity factor, and performance ratio of large-scale PV plant Perfect for professionals in the solar power industry, Step-by-Step Design of Large-Scale Photovoltaic Power Plants will also earn a place in the libraries of equipment manufacturers and university professors seeking a one-stop resource for the design of PV power plants.

Download or read book Nanostructured Semiconductors written by Konstantinos Termentzidis and published by CRC Press. This book was released on 2017-09-01 with total page 574 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book is devoted to nanostructures and nanostructured materials containing both amorphous and crystalline phases with a particular focus on their thermal properties. It is the first time that theoreticians and experimentalists from different domains gathered to treat this subject. It contains two distinct parts; the first combines theory and simulations methods with specific examples, while the second part discusses methods to fabricate nanomaterials with crystalline and amorphous phases and experimental techniques to measure the thermal conductivity of such materials. Physical insights are given in the first part of the book, related with the existing theoretical models and the state of art simulations methods (molecular dynamics, ab-initio simulations, kinetic theory of gases). In the second part, engineering advances in the nanofabrication of crystalline/amorphous heterostructures (heavy ion irradiation, electrochemical etching, aging/recrystallization, ball milling, PVD, laser crystallization and magnetron sputtering) and adequate experimental measurement methods are analyzed (Scanning Thermal Microscopy, Raman, thermal wave methods and x-rays neutrons spectroscopy).

Download or read book Physics of Thin Film Photovoltaics written by Victor G. Karpov and published by John Wiley & Sons. This book was released on 2021-11-09 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: PHYSICS OF THIN-FILM PHOTOVOLTAICS Tackling one of the hottest topics in renewables, thin-film photovoltaics, the authors present the latest updates, technologies, and applications, offering the most up-to-date and thorough coverage available to the engineer, scientist, or student. It appears rather paradoxical that thin-film photovoltaics (PVs) are made of materials that seem unacceptable from the classical PV perspective, and yet they often outperform classical PV. This exciting new volume solves that paradox by switching to a new physics paradigm. Many concepts here fall beyond the classical PV scope. The differences lie in device thinness (microns instead of millimeters) and morphology (non-crystalline instead of crystalline). In such structures, the charge carriers can reach electrodes without recombination. On the other hand, thin disordered structures render a possibility of detrimental lateral nonuniformities (“recombination highways”), and their energy spectra give rise to new recombination modes. The mechanisms of thermal exchange and device degradation are correspondingly unique. The overall objective of this book is to give a self-contained in-depth discussion of the physics of thin-film systems in a manner accessible to both researchers and students. It covers most aspects of the physics of thin-film PV, including device operations, material structure and parameters, thin-film junction formation, analytical and numerical modeling, concepts of large area effects and lateral non-uniformities, physics of shunting (both shunt growth and effects), and device degradation. Also, it reviews a variety of physical diagnostic techniques proven with thin-film PV. Whether for the veteran engineer or the student, this is a must-have for any library. This outstanding new volume: Covers not only the state-of-the-art of thin-film photovoltaics, but also the basics, making this volume useful not just to the veteran engineer, but the new-hire or student as well Offers a comprehensive coverage of thin-film photovoltaics, including operations, modeling, non-uniformities, piezo-effects, and degradation Includes novel concepts and applications never presented in book format before Is an essential reference, not just for the engineer, scientist, and student, but the unassuming level of presentation also makes it accessible to readers with a limited physics background Is filled with workable examples and designs that are helpful for practical applications Is useful as a textbook for researchers, students, and faculty for understanding new ideas in this rapidly emerging field Audience: Industrial professionals in photovoltaics, such as engineers, managers, research and development staff, technicians, government and private research labs; also academic and research universities, such as physics, chemistry, and electrical engineering departments, and graduate and undergraduate students studying electronic devices, semiconductors, and energy disciplines

Download or read book Building Physics and Building Energy Systems written by Davide Astiaso Garcia and published by MDPI. This book was released on 2021-03-19 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt: The energy transition is one of the key approaches in the effort to halt climate changes, and it has become even more essential in the light of the recent COVID-19 pandemic. Fostering the energy efficiency and the energy independence of the building sector is a focal aim to move towards a decarbonized society. In this context, building physics and building energy systems are fundamental disciplines based on applied physics applications in civil, architectural, and environmental engineering, including technical themes related to the planning of energy and the environment, diagnostic methods, and mitigating techniques. This Special Issue contains information on experimental studies in the following research topics: renewable energy sources, building energy analysis, rational use of energy, heat transmission, heating and cooling systems, thermofluid dynamics, smart energy systems, and energy service management in buildings.

Download or read book Nanotechnology and Photovoltaic Devices written by Jan Valenta and published by CRC Press. This book was released on 2015-06-01 with total page 441 pages. Available in PDF, EPUB and Kindle. Book excerpt: Silicon is an abundant element and is produced in large quantities for the electronic industry. The falling price of this commodity also feeds the growth of solar photovoltaics (PV). However, solar cells (SCs) based on bulk semiconductors have quite limited maximum attainable performance. Therefore, new principles and materials are being investigat

Download or read book Photovoltaic and Photoactive Materials written by Joseph M. Marshall and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary objective of this NATO Advanced Study Institute (ASI) was to present an up-to-date overview of various current areas of interest in the field of photovoltaic and related photoactive materials. This is a wide-ranging subject area, of significant commercial and environmental interest, and involves major contributions from the disciplines of physics, chemistry, materials, electrical and instrumentation engineering, commercial realisation etc. Therefore, we sought to adopt an inter disciplinary approach, bringing together recognised experts in the various fields while retaining a level of treatment accessible to those active in specific individual areas of research and development. The lecture programme commenced with overviews of the present relevance and historical development of the subject area, plus an introduction to various underlying physical principles of importance to the materials and devices to be addressed in later lectures. Building upon this, the ASI then progressed to more detailed aspects of the subject area. We were also fortunately able to obtain a contribution from Thierry Langlois d'Estaintot of the European Commission Directorate, describing present and future EC support for activities in this field. In addition, poster sessions were held throughout the meeting, to allow participants to present and discuss their current activities. These were supported by what proved to be very effective feedback sessions (special thanks to Martin Stutzmann), prior to which groups of participants enthusiastically met (often in the bar) to identify and agree topics of common interest.

Download or read book Modelling and Design of Nanostructured Optoelectronic Devices written by Jagdish A. Krishnaswamy and published by Springer Nature. This book was released on 2022-04-02 with total page 293 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book approaches the design of functionally superior optoelectronic devices through the use of bio-inspired nanostructures and multiscale material structures through a step-by-step approach. The book combines both the fundamental theoretical concepts involved in understanding and numerically modelling optoelectronic devices and the application of such methods in addressing challenging research problems in nanostructured optoelectronic design and fabrication. The book offers comprehensive content in optoelectronic materials and engineering and can be used as a reference material by researchers in nanostructured optoelectronic design.

Download or read book Multi physics Modeling and Simulation of Photovoltaic Devices and Systems written by Timofey Golubev and published by . This book was released on 2020 with total page 239 pages. Available in PDF, EPUB and Kindle. Book excerpt: Physics-based computational modeling is an essential aspect of research and development of new photovoltaic (PV) technologies. For example, PV modeling allows us to improve our understanding of device physics, evaluate the potential of new device architectures prior to experimentation, and predict the energy production of PV systems. This dissertation describes the development of improvements to PV modeling at both the device and system levels, as well as the application of these models to obtain new insights into device physics and PV system performance.The first half of this thesis focuses on solar cell modeling using the drift-diffusion approach. Investigations into numerical instabilities of a drift-diffusion model for bilayer organic solar cells are described, and techniques for improving convergence behavior are presented. The drift-diffusion approach is then adapted for planar perovskite solar cells, validated against literature results, and utilized to understand a new experimental result involving the impact of ultrathin fullerene layers on device performance. The second half of this thesis expands our modeling to PV systems. Here, we focus on the effects of temperature and soiling (accumulation of particulate matter on PV module surfaces) on PV system energy production. A general semi-physical model for predicting annual PV soiling losses is developed and integrated with open-source PV performance models and commercial algorithms for PV system cleaning schedule optimization. Additionally, the potentials of machine learning approaches to soiling modeling are discussed and a proof-of-concept is demonstrated. In order to consider the impact of temperature on PV module performance, a coupled thermal-electrical modeling approach is developed by combining temperature-dependent equivalent circuit models with a commercial heat transfer solver. This approach also allows for predicting energy production of PV modules or films installed on irregular surfaces, such as vehicles. Application of the coupled thermal-electrical approach to simulation of residential rooftop and vehicle-integrated PV systems is demonstrated. Overall, this work has resulted in an improved understanding of the numerical methods necessary to ensure stability of drift-diffusion codes, insight into the role of fullerenes in perovskite solar cells, and the development of modeling approaches than can aid in PV system engineering and improve accuracy in PV system energy production forecasting.

Download or read book Organic Photovoltaics written by Christoph Brabec and published by John Wiley & Sons. This book was released on 2011-09-22 with total page 597 pages. Available in PDF, EPUB and Kindle. Book excerpt: Providing complementary viewpoints from academia as well as technology companies, this book covers the three most important aspects of successful device design: materials, device physics, and manufacturing technologies. It also offers an insight into commercialization concerns, such as packaging technologies, system integration, reel-to-reel large scale manufacturing issues and production costs. With an introduction by Nobel Laureate Alan Heeger.

Download or read book Handbook of the Physics of Thin Film Solar Cells written by Karl W. Böer and published by Springer Science & Business. This book was released on 2014-04-23 with total page 893 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is a compendium giving a comprehensive description of the basics of semiconductor physics relevant to the design and analysis of thin film solar cell materials. It starts from the basics of material science, describing the material and its growth, defect and electrical properties, the basics of its interaction with photons and the involved statistics, proceeding to space charge effects in semiconductors and pn-junctions. Most attention is given to analyze homo- and hetero-junction solar cells using various models and applying the field-of-direction analysis for discussing current voltage characteristics, and helping to discover the involvement of high-field effects in solar cells. The comprehensive coverage of the main topics of - and relating to - solar cells with extensive reference to literature helps scientists and engineers at all levels to reach a better understanding and improvement of solar cell properties and their production. The author is one of the founders of thin film solar cell research.

Download or read book The Physics of Solar Cells written by Juan Bisquert and published by CRC Press. This book was released on 2017-11-15 with total page 239 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book provides an explanation of the operation of photovoltaic devices from a broad perspective that embraces a variety of materials concepts, from nanostructured and highly disordered organic materials, to highly efficient devices such as the lead halide perovskite solar cells. The book establishes from the beginning a simple but very rich model of a solar cell, in order to develop and understand step by step the photovoltaic operation according to fundamental physical properties and constraints. It emphasizes the aspects pertaining to the functioning of a solar cell and the determination of limiting efficiencies of energy conversion. The final chapters of the book establish a more refined and realistic treatment of the many factors that determine the actual performance of experimental devices: transport gradients, interfacial recombination, optical losses and so forth. The book finishes with a short review of additional important aspects of solar energy conversion, such as the photonic aspects of spectral modification, and the direct conversion of solar photons to chemical fuel via electrochemical reactions.

Download or read book Handbook of Photovoltaic Science and Engineering written by Antonio Luque and published by John Wiley & Sons. This book was released on 2011-03-29 with total page 1172 pages. Available in PDF, EPUB and Kindle. Book excerpt: The most comprehensive, authoritative and widely cited reference on photovoltaic solar energy Fully revised and updated, the Handbook of Photovoltaic Science and Engineering, Second Edition incorporates the substantial technological advances and research developments in photovoltaics since its previous release. All topics relating to the photovoltaic (PV) industry are discussed with contributions by distinguished international experts in the field. Significant new coverage includes: three completely new chapters and six chapters with new authors device structures, processing, and manufacturing options for the three major thin film PV technologies high performance approaches for multijunction, concentrator, and space applications new types of organic polymer and dye-sensitized solar cells economic analysis of various policy options to stimulate PV growth including effect of public and private investment Detailed treatment covers: scientific basis of the photovoltaic effect and solar cell operation the production of solar silicon and of silicon-based solar cells and modules how choice of semiconductor materials and their production influence costs and performance making measurements on solar cells and modules and how to relate results under standardised test conditions to real outdoor performance photovoltaic system installation and operation of components such as inverters and batteries. architectural applications of building-integrated PV Each chapter is structured to be partially accessible to beginners while providing detailed information of the physics and technology for experts. Encompassing a review of past work and the fundamentals in solar electric science, this is a leading reference and invaluable resource for all practitioners, consultants, researchers and students in the PV industry.

Download or read book A Selected Listing of NASA Scientific and Technical Reports for written by United States. National Aeronautics and Space Administration. Scientific and Technical Information Division and published by . This book was released on 1964 with total page 1156 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book NASA Scientific and Technical Reports written by United States. National Aeronautics and Space Administration Scientific and Technical Information Division and published by . This book was released on 1965 with total page 1152 pages. Available in PDF, EPUB and Kindle. Book excerpt: