Download or read book Performance Evaluation of Corrosion Inhibitors and Galvanized Steel in Concrete Exposure Specimens written by Jerzy Zemajtis and published by . This book was released on 1999 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion inhibitor admixtures (CIA) and galvanized reinforcing steel (GS) are used for the corrosion protection for reinforced concrete bridges. The results of a 3.5-year evaluation of exposure specimens containing CIA from three different manufacturers and GS are presented. The specimens were built to simulate four exposure conditions typical for concrete bridges located in the coastal region or inland where deicing salts are used. The exposure conditions were Horizontal, Vertical, Tidal, and Immersed Zones. The specimens were kept inside the laboratory and were exposed to weekly ponding cycles of 6% sodium chloride solution by weight. The methods used to assess the condition of the specimens included chloride concentration measurements, corrosion potentials, and corrosion rates. Additionally, visual observations were performed for identification of rust stains and cracking on concrete surfaces. The results of chloride testing indicate that the amount of chlorides present at the bar level is more than sufficient to initiate corrosion. Chloride and rapid permeability data indicate no significant difference either in a rate of chloride ingress or in the diffusion coefficients for concretes with and without CIA. Corrosion potentials were the most negative for the Bare Steel (BS) specimen prepared with the Armatec 2000 corrosion inhibitor and generally indicated a 90% probability of active corrosion. Corrosion potentials were similar for the two BS control specimens and the BS specimen prepared with Rheocrete 222 and generally indicated an uncertain probability of corrosion. Corrosion potentials were the least negative for the BS specimen prepared with DCI-S corrosion inhibitor and generally indicated a 90% probability of no corrosion. Rate of corrosion measurements were the highest for the BS control specimens and the one prepared with A2000 and the most recent data suggest corrosion damage in 2 to 10 years. Although early rate of corrosion measurements were higher or about the same as for BS control specimens, recent measurements were slightly lower for the specimen prepared with Rheocrete 222 and suggest corrosion damage in 10 to 15 years. Rate of corrosion measurements were consistently the lowest for the BS specimens prepared with DCI-S and indicate corrosion damage is expected in 10 to 15 years. The corrosion potential and rate of corrosion data indicate that DCI-S is the only CIA evaluated that clearly provides some level of corrosion protection. A direct comparison of the GS specimens to the BS specimens is not possible because the measured potential refers to the zinc oxide and not to the steel. Nevertheless, the potential data agree with the chloride and permeability data, as well as with the visual observations, and indicate the damaging effect of a high concentration of chloride ions on the GS. At low and moderate chloride exposures, however, GS does provide corrosion protection. Recommendations are to continue monitoring until sufficient cracking has occurred in all specimens to provide for making a better estimate of the service lives of CIA and GS used in the construction of concrete bridge components in Virginia. The specimens with CIA and one control (continuous reinforcement in the legs) should be taken to the Hampton Road North Tunnel Island and placed in the brackish water to a depth of the Immersed Zone at low tide for further exposure to chloride. The specimens with GS and the other control (non-continuous reinforcement in the legs) should remain in an outdoor exposure in Southwest Virginia like the Civil Engineering Materials Research Laboratory in Blacksburg, Virginia.
Download or read book Corrosion of Reinforcing Steel in Concrete written by D. E. Tonini and published by ASTM International. This book was released on 1980 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Performance Evaluation of Various Corrosion Protection Systems of Bridges in Colorado written by Yunping Xi and published by . This book was released on 2004 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion of reinforced concrete structures has been a significant problem for many state and transportation agencies since the application of deicing salts was introduced. Much research has been conducted to develop corrosion protection systems that can prolong the life span of reinforced concrete structures. The Colorado Department of Transportation (CDOT) has several routine and experimental measures to prevent corrosion of the rebar including epoxy-coated rebar, calcium nitrite admixture, organic corrosion inhibitors, a thick cover of quality concrete, and a waterproofing membrane covered by an asphalt overlay. An extensive literature review was performed to collect information on various corrosion protection systems that have been used in the U.S. and around the world. Current CDOT practices in terms of corrosion protection measures were reviewed. A draft inspection plan for Colorado's bridge structures was proposed.
Download or read book Evaluation of Corrosion Protection Methods for Reinforced Concrete Highway Structures written by Jennifer L. Kepler and published by . This book was released on 2000 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the 1970s, research projects and field studies have been conducted on different methods for protecting reinforced concrete bridges from corrosion damage. The methods include alternative reinforcement and slab design, barrier methods, electrochemical methods, and corrosion inhibitors. Each method and its underlying principles are described, performance results of laboratory and/or field trials are reviewed, and systems are evaluated based on the results of the trials. Using performance results from the studies and costs obtained from transportation agencies, an economic analysis is used to estimate the cost of each system over a 75-year economic life using discount rates of 2%, 4% and 6%.
Download or read book Corrosion of Reinforcing Steel in Concrete written by J. Tonini and published by ASTM International. This book was released on 1980 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion Protection Performance of Corrosion Inhibitors and Epoxy coated Reinforcing Steel in a Simulated Concrete Pore Water Solution written by Wioleta A. Pyć and published by . This book was released on 1998 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt: We used a simulated concrete pore water solution to evaluate the corrosion protection performance of concrete corrosion-inhibiting admixtures and epoxy-coated reinforcing bars (ECR). We evaluated three commercial corrosion inhibitors, ECR from three coaters removed from job sites, one ECR shipped directly from the coater's plant, and one ECR removed from a job site plus a corrosion inhibitor. The corrosion inhibitors were calcium nitrite, an aqueous mixture of esters and amines, and a mixture of alcohol and amine. Corrosion protection performance was based on the amount of visually observed corroded surface area. For bare steel tested with and without corrosion inhibitors, corrosion increased with increasing chloride concentration, and specimens saturated with oxygen were more corroded than specimens saturated with breathing air. The amount of corrosion over the 90-day test period was controlled by the amount of oxygen in solution at the higher chloride concentrations. The ester-amine and alcohol-amine did not inhibit corrosion. Calcium nitrite inhibited corrosion at all levels of chloride concentration. For ECR, corrosion occurred both at sites where the coating was damaged and underneath the coating. Coating debondment was greatest in pore water solutions containing chloride. The least coating debondment and corrosion occurred in the solution containing calcium nitrite and the ECR shipped directly from the manufacturer. Coating debondment and corrosion of ECR are directly related to the amount of damage as holes; mashed, dented, and cracked areas; and holidays. The researchers recommend that the developed test method be adopted as a standard test for concrete corrosion inhibitors and that calcium nitrite remain the only concrete corrosion inhibitor approved for use in Virginia.
Download or read book Evaluation of Economical and Efficient Method for Corrosion Protection of Structural Concrete written by Branko N. Popov and published by . This book was released on 1998 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt: In situ corrosion studies were carried out on steel and galvanized steel rods embedded in concrete cylinders. The concrete samples were prepared with different contents of DCI and Rh222 inhibitors in the concrete mix. The corrosion testing was carried out in absence and presence of chlorides in the electrolyte using standard electrochemical methods. The results were compared with the corrosion studies performed on steel substrates and on galvanized steel in model solutions which simulated the rebar-concrete interface. A transient one dimensional mathematical model has been developed and used to predict the corrosion initiation time in a concrete cylinder.
Download or read book Galvanized Steel Reinforcement in Concrete written by Stephen Yeomans and published by Elsevier. This book was released on 2004-11-26 with total page 316 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reinforced concrete is one of the most widely used modern materials of construction. It is comparatively cheap, readily available, and suitable for a variety of building and construction applications. Galvanized Steel Reinforcement in Concrete provides a detailed resource covering all aspects of this important material. Both servicability and durability aspects are well covered, with all the information needed maximise the life of buildings constructed from it. Containing an up-to-date and comprehensive collection of technical information and data from world renound authors, it will be a valuable source of reference for academics, researchers, students and professionals alike. Provides information vital to prolong the life of buildings constructed from this versatile material Brings together a disparate body of knowledge from many parts of the world into a concise and authoritative text Containing an up-to-date and comprehensive collection of technical information
Download or read book Durability of Galvanized Steel in Concrete written by K. W. J. Treadaway and published by . This book was released on with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Evaluation of Corrosion Inhibitors in Chloride contaminated Reinforced Concrete written by Roumiana Hristova and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The report describes research to determine the effectiveness of commercial corrosion-inhibiting admixtures on the corrosion of reinforcing steel in chloride contaminated concrete. Domestic and foreign publications were reviewed to locate performance data and current practices related to the use, testing and evaluation of corrosion inhibiting admixtures. The study consisted of identification and evaluation of the currently used corrosion-inhibiting admixtures in the United States and other countries. A list of available corrosion-inhibiting admixtures were appraised. Consideration was given to performance predictability, practicality, cost, and other pertinent factors. Five-year old "lollipop" concrete speciments containing sodium nitrite and dinitrobenzoic acid as corrosion inhibitors, and comparison with control specimens were studied using linear polarization and impedance spectroscopy. All mixes had different amounts of calcium chloride added. An equivalent circuit model considering the physical characteristics of the rebar/concrete interface was used to simulate the impedance spectra. The RC parameters obtained from the impedance simulation, including maximum phase angle shift, surface impedance and capacitive responses, were utilized to characterize the surface corrosion of embedded steel and to evaluate the effect of inhibitors with chloride content. The corrosion current densities determined by impedance measurement were compared with those determined using linear polarization and good agreement between the two methods was obtained.
Download or read book Corrosion of Steel in Concrete Structures written by Amir Poursaee and published by Woodhead Publishing. This book was released on 2016-02-17 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion of reinforcing steel is now recognized as the major cause of degradation of concrete structures in many parts of the world. Despite this, infrastructure expenditure is being unreasonably decreased by sequestration and the incredible shrinking discretionary budget. All components of our infrastructure including highways, airports, water supply, waste treatment, energy supply, and power generation require significant investment and are subjected to degradation by corrosion, which significantly reduces the service life, reliability, functionality of structures and equipment, and safety. Corrosion of Steel in Concrete Structures provides a comprehensive review of the subject, in addition to recent advances in research and technological developments, from reinforcing materials to measurement techniques and modelling. This book contains not only all the important aspects in the field of corrosion of steel reinforced concrete but also discusses new topics and future trends. Part One of the book tackles theoretical concepts of corrosion of steel in concrete structures. The second part moves on to analyse the variety of reinforcing materials and concrete, including stainless steel and galvanized steel. Part Three covers measurements and evaluations, such as electrochemical techniques and acoustic emission. Part Four reviews protection and maintenance methods, whilst the final section analyses modelling, latest developments and future trends in the field. The book is essential reading for researchers, practitioners and engineers who are involved in materials characterisation and corrosion of steel in concrete structures. Provides comprehensive coverage on a broad range of topics related to the corrosion of steel bars in concrete Discusses the latest measuring methods and advanced modeling techniques Reviews the range of reinforcing materials and types of concrete
Download or read book Corrosion Inhibitors in Concrete written by and published by . This book was released on 2002 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: The overall objective of this work in progress is to assess the effectiveness of corrosion inhibitors for steel in concrete. Three commercially available inhibitors, DCI-S (calcium nitrite-based), and FerroGard 901 and Rheocrete 222+ (both based on organic compounds), were selected for detailed examination. To determine the amount of inhibitor remaining in concrete, an accurate method to analyze for calcium nitrite was developed, and analyses for the other two inhibitors are being explored. The ability of calcium nitrite to stay in place was examined by laboratory experiments of inhibitor diffusion in concrete and by examination of available concrete samples exposed for long times to the outdoors environment.
Download or read book Corrosion of Steel in Concrete Structures written by Amir Poursaee and published by Woodhead Publishing. This book was released on 2023-02-20 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt: Essential reading for researchers, practitioners, and engineers, this book covers not only all the important aspects in the field of corrosion of steel reinforced concrete but also discusses new topics and future trends. Theoretical concepts of corrosion of steel in concrete structures, the variety of reinforcing materials and concrete, including stainless steel and galvanized steel, measurements and evaluations, such as electrochemical techniques and acoustic emission, protection and maintenance methods, and modelling, latest developments, and future trends in the field are discussed. Comprehensive coverage of the corrosion of steel bars in concrete, investigating the range of reinforcing materials, and types of concrete Introduces the latest measuring methods, data collection, and advanced modeling techniques Second edition covers a range of new, emerging topics such as the concept of chloride threshold value, concrete permeability and chloride diffusion, the role of steel microstructure, and innovations in corrosion detection devices
Download or read book Project Titled written by Branko N. Popov and published by . This book was released on 2003 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion of Steel in Concrete written by Luca Bertolini and published by John Wiley & Sons. This book was released on 2013-02-26 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: Steel-reinforced concrete is used ubiquitously as a building material due to its unique combination of the high compressive strength of concrete and the high tensile strength of steel. Therefore, reinforced concrete is an ideal composite material that is used for a wide range of applications in structural engineering such as buildings, bridges, tunnels, harbor quays, foundations, tanks and pipes. To ensure durability of these structures, however, measures must be taken to prevent, diagnose and, if necessary, repair damage to the material especially due to corrosion of the steel reinforcement. The book examines the different aspects of corrosion of steel in concrete, starting from basic and essential mechanisms of the phenomenon, moving up to practical consequences for designers, contractors and owners both for new and existing reinforced and prestressed concrete structures. It covers general aspects of corrosion and protection of reinforcement, forms of attack in the presence of carbonation and chlorides, problems of hydrogen embrittlement as well as techniques of diagnosis, monitoring and repair. This second edition updates the contents with recent findings on the different topics considered and bibliographic references, with particular attention to recent European standards. This book is a self-contained treatment for civil and construction engineers, material scientists, advanced students and architects concerned with the design and maintenance of reinforced concrete structures. Readers will benefit from the knowledge, tools, and methods needed to understand corrosion in reinforced concrete and how to prevent it or keep it within acceptable limits.
Download or read book Structural Performance Evaluation of the Postrite Post treatment Corrosion Inhibitor System written by Jonanthan Matthew Winkler and published by . This book was released on 1996 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Field Evaluation of Corrosion Inhibitors for Concrete written by Michael M. Sprinkel and published by . This book was released on 2003 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt:
