Download or read book Performance based Measurement of Optimum Moisture for Soil Compaction written by Bradley J. Hansen and published by . This book was released on 2013 with total page 41 pages. Available in PDF, EPUB and Kindle. Book excerpt: Part of the challenge achieving maximum field density in subgrade materials is transferring the optimal compaction and moisture content data from laboratory testing to the field. This research investigated the proficiency of four different instruments at accurately predicting moisture contents of three subgrade soils (loam, silt, silty/clay) commonly used in Minnesota roadway construction projects. The four instruments were; DOT600 (moisture content), WP4C dewpoint potentiometer (matric suction), the Button Heat Pulse Sensor (BHPS) (temperature rise vs. moisture content), and an exudation pressure test device. The DOT600 showed a strong correlation between the output period (measured in micro-seconds) and volumetric water content. The WP4C did not accurately measure matric suction for any of the loam, silt or silt/clay soils at suctions below 250 kPa. Published data shows that the matric suction of soils compacted at optimum moisture content is usually in the range of 200 - 300 kPa. The BHPS showed a strong correlation between measured temperature rise and water content but in its current configuration is not rigorous enough to withstand field conditions. The exudation pressure device was applied to soils compacted in a AASHTO T99 mold at various moisture contents. Water was exuded from the packed samples at pressures between 100 and 500 psi corresponding to AASHTO-T99 moisture contents of 10 to 25%. Accurate moisture content readings from any of these instruments may not be as important as a more precise and simple calibration between the measurement units of the instrument and the optimum moisture content determined from the AASHTO T99 test.
Download or read book Earth Manual written by United States. Bureau of Reclamation and published by . This book was released on 1990 with total page 356 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book QA QC of Subgrade and Embankment Construction written by Eshan Ganju and published by . This book was released on 2015-09-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The Dynamic Cone Penetrometer (DCP) is a device that is used for the estimation of in situ compaction quality of constructed subgrades and embankments. It is a relatively inexpensive, light-weight and easy to use device that measures the dynamic penetration resistance of the compacted soil, from which an estimate of soil strength and stiffness characteristics can be made. Owing to its ease of use, many DOTs in the U.S. have employed the DCP in their compaction quality control procedures, and over the past few decades, extensive research has been carried out on the development of correlations between the results of the DCP test and the results of strength and stiffness tests performed on compacted soils (e.g., California bearing ratio, and resilient modulus)The objectives of this research are to refine DCP-based quality assurance and quality control correlations for compaction quality control developed by previous research studies carried out at Purdue for the Indiana Department of Transportation, especially focusing on (1) grouping of the soils based on their mechanical response to the DCP loading, and (2) limiting the in situ moisture range of the soils used for development of correlations within -2% of the optimum moisture content of the tested soil. The factors outlined above are studied, and in particular, soil grouping is examined critically. The AASHTO ('A-based') classification employed previously for classification of soils is replaced with a new classification criteria specifically developed for the DCP test. Soils are grouped into one of the two categories of coarse-grained or fine-grained soils on the basis of the size of the dominant particle in the soil. The criteria developed for the classification of soil into one of these two categories is based on index properties of the soil, such as the standard Proctor maximum dry density, optimum moisture content, plasticity index (PI) and fines content.
Download or read book Precision of Soil Compaction Tests Maximum Dry Density and Optimum Moisture Content written by and published by . This book was released on 1994 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Landfill and Surface Impoundment Performance Evaluation Manual written by Charles A. Moore and published by . This book was released on 1983 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings First North American Workshop on Modeling the Mechanics of Off Road Mobility 5 6 May 1994 written by Roger W. Meier and published by . This book was released on 1994 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Electrical Measuring Instruments and Measurements written by S.C. Bhargava and published by CRC Press. This book was released on 2012-12-27 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book, written for the benefit of engineering students and practicing engineers alike, is the culmination of the author's four decades of experience related to the subject of electrical measurements, comprising nearly 30 years of experimental research and more than 15 years of teaching at several engineering institutions. The unique feature of this book, apart from covering the syllabi of various universities, is the style of presentation of all important aspects and features of electrical measurements, with neatly and clearly drawn figures, diagrams and colour and b/w photos that illustrate details of instruments among other things, making the text easy to follow and comprehend. Enhancing the chapters are interspersed explanatory comments and, where necessary, footnotes to help better understanding of the chapter contents. Also, each chapter begins with a "recall" to link the subject matter with the related science or phenomenon and fundamental background. The first few chapters of the book comprise "Units, Dimensions and Standards"; "Electricity, Magnetism and Electromagnetism" and "Network Analysis". These topics form the basics of electrical measurements and provide a better understanding of the main topics discussed in later chapters. The last two chapters represent valuable assets of the book, and relate to (a) "Magnetic Measurements", describing many unique features not easily available elsewhere, a good study of which is essential for the design and development of most electric equipment – from motors to transformers and alternators, and (b) "Measurement of Non-electrical Quantities", dealing extensively with the measuring techniques of a number of variables that constitute an important requirement of engineering measurement practices. The book is supplemented by ten appendices covering various aspects dealing with the art and science of electrical measurement and of relevance to some of the topics in main chapters. Other useful features of the book include an elaborate chapter-by-chapter list of symbols, worked examples, exercises and quiz questions at the end of each chapter, and extensive authors' and subject index. This book will be of interest to all students taking courses in electrical measurements as a part of a B.Tech. in electrical engineering. Professionals in the field of electrical engineering will also find the book of use.
Download or read book Earth Manual written by and published by . This book was released on 1990 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Soil Improvement and Ground Modification Methods written by Peter G. Nicholson and published by Butterworth-Heinemann. This book was released on 2014-08-29 with total page 474 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by an author with more than 25 years of field and academic experience, Soil Improvement and Ground Modification Methods explains ground improvement technologies for converting marginal soil into soil that will support all types of structures. Soil improvement is the alteration of any property of a soil to improve its engineering performance. Some sort of soil improvement must happen on every construction site. This combined with rapid urbanization and the industrial growth presents a huge dilemma to providing a solid structure at a competitive price. The perfect guide for new or practicing engineers, this reference covers projects involving soil stabilization and soil admixtures, including utilization of industrial waste and by-products, commercially available soil admixtures, conventional soil improvement techniques, and state-of-the-art testing methods. - Conventional soil improvement techniques and state-of-the-art testing methods - Methods for mitigating or removing the risk of liquefaction in the event of major vibrations - Structural elements for stabilization of new or existing construction industrial waste/by-products, commercially available soil - Innovative techniques for drainage, filtration, dewatering, stabilization of waste, and contaminant control and removal
Download or read book A Comparison of Density Based and Modulus Based In Situ Test Measurements for Compaction Control written by Christopher L. Meehan and published by . This book was released on 2012 with total page 13 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper presents and compares the results from a series of in situ density-based and modulus-based compaction control tests that were conducted during construction of a coarse-grained soil embankment. To simulate current construction practices as closely as possible, these in situ tests were performed on an embankment that was constructed and compacted by a vibratory smooth drum roller in a series of lifts. During construction of the test embankment, the compaction process was monitored using the nuclear density gauge device and a number of alternative modulus-based devices, including the lightweight deflectometer, the dynamic cone penetrometer, and the soil stiffness gauge. Comparison of the in situ test results illustrates that point-to-point variability in measured values is quite common for each of these test devices, to varying degrees for the different devices that were examined. Consistent increases in measured soil properties from pass-to-pass of the compactor are considered critical for proper control of the compaction process, with some devices faring better than others in this area of performance. The measured modulus values correlated poorly to the nuclear density gauge dry unit weights, and also correlated poorly with other measured moduli when the results from different devices were compared. This lack of agreement was likely caused by a variety of factors including: variations in the magnitude of strain and rate of strain application between the different modulus-based devices, variations in the tested volume between the different devices, and variations in the local moisture content and matrix suction conditions. Finally, the effect of soil moisture content was shown to be critically important when interpreting the results from modulus-based tests, and the utility of multiple regression analyses was explored for including this effect.
Download or read book Mechanics of Residual Soils Second Edition written by Geoffrey E. Blight and published by CRC Press. This book was released on 2012-05-03 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: Residual soils are found in many parts of the world and are used extensively as construction materials for roads, embankments and dams, and to support the foundations of buildings, bridges and load-bearing pavements. The characteristics and engineering properties of residual soils can differ significantly from those of the more familiar transported soils. The fact that residual soils occur often in areas with tropical and sub-tropical climates and (extensively) in semi-arid climates, adds another dimension to their engineering performance, that of unsaturation. Although there are many books that deal with the mechanics of soils, these are based mainly on the characteristics and behaviour of saturated transported soils. The first edition of this book was the first book to be written specifically about the mechanics of residual soils. The book was prepared by a panel of authors drawn from the Technical Committee on Tropical and Residual Soils of the International Society for Soil Mechanics and Foundation Engineering. It was written as a practical professional guide for geotechnical engineers working with residual soils. The second edition has retained the valuable information contained in the first edition. The present editors and authors have extensively revised and augmented the content to bring it completely up to date, adding significantly to the sections on unsaturated soil mechanics and expanding the range and number of instructive case histories. Furthermore, sections on pedocretes, dispersive soils and karst have been added.
Download or read book Proceedings of the 4th International Conference on Performance Based Design in Earthquake Geotechnical Engineering Beijing 2022 written by Lanmin Wang and published by Springer Nature. This book was released on 2022-09-19 with total page 2417 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 4th International Conference on Performance-based Design in Earthquake Geotechnical Engineering (PBD-IV) is held in Beijing, China. The PBD-IV Conference is organized under the auspices of the International Society of Soil Mechanics and Geotechnical Engineering - Technical Committee TC203 on Earthquake Geotechnical Engineering and Associated Problems (ISSMGE-TC203). The PBD-I, PBD-II, and PBD-III events in Japan (2009), Italy (2012), and Canada (2017) respectively, were highly successful events for the international earthquake geotechnical engineering community. The PBD events have been excellent companions to the International Conference on Earthquake Geotechnical Engineering (ICEGE) series that TC203 has held in Japan (1995), Portugal (1999), USA (2004), Greece (2007), Chile (2011), New Zealand (2015), and Italy (2019). The goal of PBD-IV is to provide an open forum for delegates to interact with their international colleagues and advance performance-based design research and practices for earthquake geotechnical engineering.
Download or read book Soil Survey written by and published by . This book was released on 1975 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Concepts Terms Definitions and Methods of Measurement for Soil Compaction written by Joint ASAE-SSSA Soil Compaction Committee and published by . This book was released on 1958 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Constructing and Controlling Compaction of Earth Fills written by Donald W. Shanklin and published by ASTM International. This book was released on 2000 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Presents 22 papers, from the July 1999 symposium, written on the use of various standardized methods for specifying and controlling the compaction of soil for engineered constructed earth fills. Perspectives include the historical background, current state-of-the- art practices, case histories of challenging situations, concerns regarding appropriate design parameters for compaction control, and new methods to evaluate soil compaction and related qualities. Annotation copyrighted by Book News, Inc., Portland, OR.
Download or read book Soil Survey of various Counties Etc written by and published by . This book was released on 1963 with total page 410 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Soil Survey of Sussex County Delaware written by William Ireland and published by . This book was released on 1974 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt:
