Download or read book Particle Size Measurement written by Terence Allen and published by Springer Science & Business Media. This book was released on 1996-12-31 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the fifth edition of the highly successful work first published in 1968, comprising two definitive volumes on particle characterisation. The first volume is devoted to sampling and particle size measurement, while surface area and pore size determination are reviewed in volume 2. Particle size and characterisation are central to understanding powder properties and behaviour. This book describes numerous potential measuring devices, how they operate and their advantages and disadvantages. It comprise a fully comprehensive treatise on the wide range of available equipment with an extensive literature survey, and a list of manufacturers and suppliers. The author's blend of academic and industrial experience results in a readable technical book with information on how to analyse, present, and extract useful information from data. This is an essential reference book for both industrial and academic research workers in a variety of areas including: pharmaceuticals, food science, pollution analysis and control, electronic materials, agricultural products, polymers, pigments and chemicals.
Download or read book Particle Size Measurement written by Terence Allen and published by Springer. This book was released on 1996-12-31 with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the fifth edition of the highly successful work first published in 1968, comprising two definitive volumes on particle characterisation. The first volume is devoted to sampling and particle size measurement, while surface area and pore size determination are reviewed in volume 2. Particle size and characterisation are central to understanding powder properties and behaviour. This book describes numerous potential measuring devices, how they operate and their advantages and disadvantages. It comprise a fully comprehensive treatise on the wide range of available equipment with an extensive literature survey, and a list of manufacturers and suppliers. The author's blend of academic and industrial experience results in a readable technical book with information on how to analyse, present, and extract useful information from data. This is an essential reference book for both industrial and academic research workers in a variety of areas including: pharmaceuticals, food science, pollution analysis and control, electronic materials, agricultural products, polymers, pigments and chemicals.
Download or read book Particle Size Measurement written by Terence Allen and published by Springer. This book was released on 1996-12-31 with total page 824 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the fifth edition of the highly successful work first published in 1968, comprising two definitive volumes on particle characterisation. The first volume is devoted to sampling and particle size measurement, while surface area and pore size determination are reviewed in volume 2. Particle size and characterisation are central to understanding powder properties and behaviour. This book describes numerous potential measuring devices, how they operate and their advantages and disadvantages. It comprise a fully comprehensive treatise on the wide range of available equipment with an extensive literature survey, and a list of manufacturers and suppliers. The author's blend of academic and industrial experience results in a readable technical book with information on how to analyse, present, and extract useful information from data. This is an essential reference book for both industrial and academic research workers in a variety of areas including: pharmaceuticals, food science, pollution analysis and control, electronic materials, agricultural products, polymers, pigments and chemicals.
Download or read book Particle Size Measurement Surface area and pore size determination written by Terence Allen and published by . This book was released on 1997 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Particle Size Measurement written by Terence Allen and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 830 pages. Available in PDF, EPUB and Kindle. Book excerpt: Powder technology is a subject in its own right, and powder characterization is central to an understanding of this discipline. In the eight years since the printing of the third edition of Particle Size Measurement there have been two big changes in my life. After thirty years of academia I have returned to industry, and after a lifetime in Great Britain I have emigrated to the United States. In industry the initial demand is to relate powder properties to product performance and then to maintain powder consistency. This requires on-line or rapid off-line analysis which, in turn, has led to the demand for a whole range of new instruments whose primary function is process monitoring. Historically, chemical engineering courses have concentrated on the be haviour of fluids, and engineers enter industry relatively unschooled in the subject of powder behaviour . Yet, when my colleagues Reg Davies and John Boughton surveyed three thousand Dupont products, they discovered that 80% involved powder at some stage of their manufacture. The results of this survey illustrate the need for more training in this key subject. This edition reflects the changing image of powder characterization towards in-process size analysis. Hence the chapter covering on-line analysis has been largely re-written. Apart from this, I have expanded certain sections and describe the new instruments that have been introduced since the last edition.
Download or read book Particle Size and Surface Area Measurement written by and published by . This book was released on 1972 with total page 92 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Particle Size Analysis written by N G Stanley-Wood and published by Royal Society of Chemistry. This book was released on 2007-10-31 with total page 557 pages. Available in PDF, EPUB and Kindle. Book excerpt: Particle Size Analysis reviews the development of particle characterization over the past 25 years and also speculates on its future. Interest in the subject has increased enormously over the years and this book highlights the changes and advances made within the field. This book is comprehensive in its coverage of particle size analysis and includes contributions on such characterization techniques as microscopy using fractal analysis, light diffraction, light scattering with the phase doppler technique, light observation, and photon correlation spectroscopy. A number of chapters address the interest in on-line in-stream particle size analysis and illustrate the progress being made in achieving this long sought after ideal of in-situ in-process particle characterization. Applications to other technological fields are detailed by chapters covering biological systems and the pharmaceutical industry. The subject of surface area determination is considered with particular emphasis on the measurements on porosity of powders, the characterization and comparability of reference materials, and the need for standards. Particle Size Analysis should provide stimulating reading for technologists, scientists, and engineers involved in particle characterization and powder technology worldwide.
Download or read book Characterization of Porous Solids and Powders Surface Area Pore Size and Density written by S. Lowell and published by Springer Science & Business Media. This book was released on 2012-09-14 with total page 365 pages. Available in PDF, EPUB and Kindle. Book excerpt: The growth of interest in newly developed porous materials has prompted the writing of this book for those who have the need to make meaningful measurements without the benefit of years of experience. One might consider this new book as the 4th edition of "Powder Surface Area and Porosity" (Lowell & Shields), but for this new edition we set out to incorporate recent developments in the understanding of fluids in many types of porous materials, not just powders. Based on this, we felt that it would be prudent to change the title to "Characterization of Porous Solids and Powders: Surface Area, Porosity and Density". This book gives a unique overview of principles associated with the characterization of solids with regard to their surface area, pore size, pore volume and density. It covers methods based on gas adsorption (both physi and chemisorption), mercury porosimetry and pycnometry. Not only are the theoretical and experimental basics of these techniques presented in detail but also, in light of the tremendous progress made in recent years in materials science and nanotechnology, the most recent developments are described. In particular, the application of classical theories and methods for pore size analysis are contrasted with the most advanced microscopic theories based on statistical mechanics (e.g. Density Functional Theory and Molecular Simulation). The characterization of heterogeneous catalysts is more prominent than in earlier editions; the sections on mercury porosimetry and particularly chemisorption have been updated and greatly expanded.
Download or read book Fine Particle Measurement Size Surface and Pore Volume written by Clyde Orr and published by . This book was released on 1959 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Powder Surface Area and Porosity written by S. Lowell and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 261 pages. Available in PDF, EPUB and Kindle. Book excerpt: The rapid growth of interest in powders and their surface properties in many diverse industries prompted the writing of this book for those who have the need to make meaningful measurements without the benefit of years of experience. It is intended as an introduction to some of the elementary theory and experimental methods used to study the surface area, porosity, density, and particle size of powders. It may be found useful by those with little or no training in solid surfaces who have the need to learn quickly the rudiments of surface area, density, pore size, and particle size measurements. S. Lowell J.E. Shields Symbols Use of symbols for purposes other than those indicated in the following table are so defined in the text. Some symbols not shown in the table are also defined in the text. d adsorbate cross-sectional area A area; condensation coefficient; collision frequency C BET constant c concentration D diameter; coefficient of thermal diffusion E adsorption potential permeability aspect factor f F flow rate; force; feed rate g gravitational constant G Gibbs free energy S G free surface energy h heat of immersion per unit area; height H enthalpy heat of immersion Hi heat of adsorption Hsv BET intercept; filament current k thermal conductivity; specific reaction rate K Harkins-Jura constant C length L heat of liquefaction M mass M molecular weight MPa megapascals number of moles n number of molecules; number of particles N N Avogadro's num'ber molecular collisions per square cm per second
Download or read book Powder Surface Area and Porosity written by S. Lowell and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: The rapid growth of interest in powders and their surface properties in many diverse industries prompted the writing of this book for those who have the need to make meaningful measurements without the benefit of years of experience. It is intended as an introduction to some of the elementary theory and experimental methods used to study the surface area, porosity and density of powders. It may be found useful by those with little or no training in solid surfaces who have the need to quickly learn the rudiments of surface area, density and pore-size measurements. Syosset, New York S. Lowell May, 1983 J. E. Shields Xl List of symbols Use of symbols for purposes other than those indicated in the following list are so defined in the text. Some symbols not shown in this list are defined in the text. d adsorbate cross-sectional area A area; condensation coefficient; collision frequency C BET constant c concentration D diameter; coefficient of thermal diffusion E adsorption potential f permeability aspect factor F flow rate; force; feed rate 9 gravitational constant G Gibbs free energy GS free surface energy h heat of immersion per unit area; height H enthalpy Hi heat of immersion Hsv heat of adsorption BET intercept; filament current k thermal conductivity; specific reaction rate K Harkins-Jura constant I length L heat of liquefaction M mass M molecular weight n number of moles N number of molecules; number of particles N Avagadro's number .
Download or read book Experimental Methods and Instrumentation for Chemical Engineers written by Gregory S. Patience and published by Elsevier. This book was released on 2017-09-08 with total page 426 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experimental Methods and Instrumentation for Chemical Engineers, Second Edition, touches many aspects of engineering practice, research, and statistics. The principles of unit operations, transport phenomena, and plant design constitute the focus of chemical engineering in the latter years of the curricula. Experimental methods and instrumentation is the precursor to these subjects. This resource integrates these concepts with statistics and uncertainty analysis to define what is necessary to measure and to control, how precisely and how often.The completely updated second edition is divided into several themes related to data: metrology, notions of statistics, and design of experiments. The book then covers basic principles of sensing devices, with a brand new chapter covering force and mass, followed by pressure, temperature, flow rate, and physico-chemical properties. It continues with chapters that describe how to measure gas and liquid concentrations, how to characterize solids, and finally a new chapter on spectroscopic techniques such as UV/Vis, IR, XRD, XPS, NMR, and XAS. Throughout the book, the author integrates the concepts of uncertainty, along with a historical context and practical examples.A problem solutions manual is available from the author upon request. Includes the basics for 1st and 2nd year chemical engineers, providing a foundation for unit operations and transport phenomena Features many practical examples Offers exercises for students at the end of each chapter Includes up-to-date detailed drawings and photos of equipment
Download or read book Characterization of Porous Solids and Powders Surface Area Pore Size and Density written by Seymour Lowell and published by Springer Science & Business Media. This book was released on 2006-04-24 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: The growth of interest in newly developed porous materials has prompted the writing of this book for those who have the need to make meaningful measurements without the benefit of years of experience. One might consider this new book as the 4th edition of "Powder Surface Area and Porosity" (Lowell & Shields), but for this new edition we set out to incorporate recent developments in the understanding of fluids in many types of porous materials, not just powders. Based on this, we felt that it would be prudent to change the title to "Characterization of Porous Solids and Powders: Surface Area, Porosity and Density". This book gives a unique overview of principles associated with the characterization of solids with regard to their surface area, pore size, pore volume and density. It covers methods based on gas adsorption (both physi and chemisorption), mercury porosimetry and pycnometry. Not only are the theoretical and experimental basics of these techniques presented in detail but also, in light of the tremendous progress made in recent years in materials science and nanotechnology, the most recent developments are described. In particular, the application of classical theories and methods for pore size analysis are contrasted with the most advanced microscopic theories based on statistical mechanics (e.g. Density Functional Theory and Molecular Simulation). The characterization of heterogeneous catalysts is more prominent than in earlier editions; the sections on mercury porosimetry and particularly chemisorption have been updated and greatly expanded.
Download or read book Design and Processing of Particulate Products written by Jim Litster and published by Cambridge University Press. This book was released on 2016-10-20 with total page 343 pages. Available in PDF, EPUB and Kindle. Book excerpt: A unique text providing comprehensive coverage of fundamental particle science, processing and technology. Including quantitative tools, real-world case studies and end-of-chapter problems, it is ideal for students in engineering and applied sciences, as well as for practitioners in a range of industries manufacturing particulate products.
Download or read book Particle Size Measurements written by Henk G. Merkus and published by Springer Science & Business Media. This book was released on 2009-01-07 with total page 535 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the practical aspects of particle size measurement: a major difference with existing books, which have a more theoretical approach. Of course, the emphasis still lies on the measurement techniques. For optimum application, their theoretical background is accompanied by quantitative quality aspects, limitations and problem identification. In addition the book covers the phenomena of sampling and dispersion of powders, either of which may be dominant in the overall analysis error. Moreover, there are chapters on the general aspects of quality for particle size analysis, quality management, reference materials and written standards, in- and on-line measurement, definitions and multilingual terminology, and on the statistics required for adequate interpretation of results. Importantly, a relation is made to product performance, both during processing as well as in final application. In view of its set-up, this book is well suited to support particle size measurement courses.
Download or read book Handbook of Non Ferrous Metal Powders written by Oleg D Neikov and published by Elsevier. This book was released on 2009-02-24 with total page 644 pages. Available in PDF, EPUB and Kindle. Book excerpt: The manufacture and use of the powders of non-ferrous metals has been taking place for many years in what was previously Soviet Russia, and a huge amount of knowledge and experience has built up in that country over the last forty years or so. Although accounts of the topic have been published in the Russian language, no English language account has existed until now. Six prominent academics and industrialists from the Ukraine and Russia have produced this highly-detailed account which covers the classification, manufacturing methods, treatment and properties of the non-ferrous metals ( aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, lead, tin, bismuth, noble metals and earth metals). The result is a formidable reference source for those in all aspects of the metal powder industry. Covers the manufacturing methods, properties and importance of the following metals: aluminium, titanium, magnesium, copper, nickel, cobalt, zinc, cadmium, noble metals, rare earth metals, lead, tin and bismuth Expert Russian team of authors, all very experienced English translation and update of book previously published in Russian
Download or read book Particle Size Analysis written by Zdeněk K. Jelínek and published by . This book was released on 1974 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt:
