Download or read book Observation of Dust in DIII D Divertor and SOL by Visible Imaging written by and published by . This book was released on 2007 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: Dust is commonly found in fusion devices. Though generally of no concern in the present day machines, dust may pose serious safety and operational concerns for ITER. Micron-size dust usually dominates the samples collected from tokamaks. During a plasma discharge micron-size dust particles can become highly mobile and travel over distances of a few meters. Once inside the plasma, dust particles heat up to over 3000 K and emit thermal radiation that can be detected by visible imaging techniques. Observations of naturally occurring and artificially introduced dusts have been performed in DIII-D divertor and scrape-off layer (SOL) using standard frame rate CMOS cameras, a gated-intensified CID camera, and a fast-framing CMOS camera. In the first 2-3 plasma discharges after a vent with personnel entry inside the vacuum vessel ('dirty vent') dust levels were quite high with thousands of particles observed in each discharge. Individual particles moving at velocities of up to a few hundred m/s and breakup of larger particles into pieces were observed. After about 15 discharges dust was virtually gone during the stationary portion of a discharge, and appeared at much reduced levels during the plasma initiation and termination phases. After a few days of plasma operations (about 70 discharges) dust levels were further reduced to just a few observed events per discharge except in discharges with current disruptions that produced significant amounts of dust. An injection of a few milligram of micron-size (6 micron median diameter) carbon dust into a high-power lower single-null ELMing H-mode discharge with strike points swept across the lower divertor floor was performed. A significant increase of the core carbon radiation was observed for about 250 ms after the injection, as the total radiated power increased twofold. Dust particles from the injection were observed by the fast framing camera in the outboard SOL near the midplane. The amount of dust observed by the fast camera immediately after the injection was.
Download or read book A Fast Visible Camera Divertor Imaging Diagnostic on DIII D written by and published by . This book was released on 2007 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent campaigns, the Photron Ultima SE fast framing camera has proven to be a powerful diagnostic when applied to imaging divertor phenomena on the National Spherical Torus Experiment (NSTX). Active areas of NSTX divertor research addressed with the fast camera include identification of types of EDGE Localized Modes (ELMs)[1], dust migration, impurity behavior and a number of phenomena related to turbulence. To compare such edge and divertor phenomena in low and high aspect ratio plasmas, a multi-institutional collaboration was developed for fast visible imaging on NSTX and DIII-D. More specifically, the collaboration was proposed to compare the NSTX small type V ELM regime [2] and the residual ELMs observed during Type I ELM suppression with external magnetic perturbations on DIII-D[3]. As part of the collaboration effort, the Photron camera was installed recently on DIII-D with a tangential view similar to the view implemented on NSTX, enabling a direct comparison between the two machines. The rapid implementation was facilitated by utilization of the existing optics that coupled the visible spectral output from the divertor vacuum ultraviolet UVTV system, which has a view similar to the view developed for the divertor tangential TV camera [4]. A remote controlled filter wheel was implemented, as was the radiation shield required for the DIII-D installation. The installation and initial operation of the camera are described in this paper, and the first images from the DIII-D divertor are presented.
Download or read book Dust Studies in DIII D and TEXTOR written by and published by . This book was released on 2009 with total page 41 pages. Available in PDF, EPUB and Kindle. Book excerpt: Studies of naturally occurring and artificially introduced carbon dust are conducted in DIII-D and TEXTOR. In DIII-D, dust does not present operational concerns except immediately after entry vents. Submicron sized dust is routinely observed using Mie scattering from a Nd:Yag laser. The source is strongly correlated with the presence of Type I edge localized modes (ELMs). Larger size (0.005-1 mm diameter) dust is observed by optical imaging, showing elevated dust levels after entry vents. Inverse dependence of the dust velocity on the inferred dust size is found from the imaging data. Direct heating of the dust particles by the neutral beam injection (NBI) and acceleration of dust particles by the plasma flows are observed. Energetic plasma disruptions produce significant amounts of dust. Large flakes or debris falling into the plasma may result in a disruption. Migration of pre-characterized carbon dust is studied in DIII-D and TEXTOR by introducing micron-size dust in plasma discharges. In DIII-D, a sample holder filled with (almost equal to)30 mg of dust is introduced in the lower divertor and exposed to high-power ELMing H-mode discharges with strike points swept across the divertor floor. After a brief exposure ((almost equal to)0.1 s) at the outer strike point, part of the dust is injected into the plasma, raising the core carbon density by a factor of 2-3 and resulting in a twofold increase of the radiated power. In TEXTOR, instrumented dust holders with 1-45 mg of dust are exposed in the scrape-off layer 0-2 cm radially outside of the last closed flux surface in discharges heated with neutral beam injection (NBI) power of 1.4 MW. At the given configuration of the launch, the dust did not penetrate the core plasma and only moderately perturbed the edge plasma, as evidenced by an increase of the edge carbon content.
Download or read book Migration of Artificially Introduced Micron Size Carbon Dust in the DIII D Divertor written by and published by . This book was released on 2006 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt: Migration of pre-characterized carbon dust in a tokamak environment was studied by introducing about 30 milligrams of dust flakes 5-10 [mu]m in diameter in the lower divertor of DIII-D using the DiMES sample holder. The dust was exposed to high power ELMing Hmode discharges in lower-single-null magnetic configuration with the strike points swept across the divertor floor. When the outer strike point (OSP) passed over the dust holder exposing it to high particle and heat fluxes, part of the dust was injected into the plasma. In about 0.1 sec following the OSP pass over the dust, 1-2% of the total dust carbon content (2-4 x 1019 carbon atoms, equivalent to a few million dust particles) penetrated the core plasma, raising the core carbon density by a factor of 2-3. When the OSP was inboard of the dust holder, the dust injection continued at a lower rate. Individual dust particles were observed moving at velocities of 10-100 m/s, predominantly in the toroidal direction for deuteron flow to the outer divertor target, consistent with the ion drag force. The observed behavior of the dust is in qualitative agreement with modeling by the 3D DustT code.
Download or read book A Tangentially Viewing Visible TV System for the DIII D Divertor written by and published by . This book was released on 1996 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: A video camera system has been installed on the DIII-D tokamak for 2-D spatial studies of line emission in the lower divertor region. The system views the divertor tangentially from an outer port at approximately the height of the X-point. At the tangency plane the entire divertor from inner wall to outside the DIII-D bias ring is viewed with spatial resolution of approximately 1 cm. The image contains information from approximately 90 degrees of toroidal angle. In a recent upgrade, remotely controllable filter changers were added which have produced images from nominally identical shots using a series of spectral lines. Software was developed to calculate the response function matrix using distributed computing techniques and assuming toroidal symmetry. Standard sparse matrix algorithms are then used to invert the 3-D images onto a poloidal plane. Spatial resolution of the inverted images is 2 cm; higher resolution simply increases the size of the response function matrix. Initial results from a series of experiments with multiple identical shots show that the emission from CII and CIII, which appears along the inner scrape-off layer above and below the X-point during ELMing H-mode, moves outward and becomes localized near the X-point in Partially Detached Divertor (PDD) operation.
Download or read book Radiation Distributions in Detached Divertor Operation on DIII D written by and published by . This book was released on 1995 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: Enhanced radiative losses with accompanying divertor heat flux reductions have been achieved on DIII-D by the puffing of deuterium and/or neon gas. In addition these highly radiating, reduced divertor heat flux regimes have been extended to lower core plasma density through cryopumping in the divertor. This paper describes the magnitude, distribution and other characteristics of the radiation obtained during these experiments. Radiated power is measured by two poloidally separated 24-channel bolometer arrays. One array views from above, the other from below the midplane. The radiated power profile is reconstructed by assuming constant emissivity on a flux surface for the core and SOL plasma and paramterizating the divertor radiation by flux surface and distance above the divertor floor. Images of visible line radiation in the divertor provide information about the distribution of impurities; e.g., a tangential image is inverted to provide a poloidal profile of the emissivity. The core plasma impurity densities are measured by charge-exchange spectroscopy techniques.
Download or read book Evolution of 2D Visible and VUV Divertor Emission Profiles During DIII D H MODE Detachment Transitions written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The peak heat flux to divertor target surfaces (P[sub div]) must be reduced, compared with present experimental levels, before a tokamak operating in the high confinement regime (H-mode) can be extrapolated to a reactor. Partially Detached Divertor (PDD) operation[1], in which deuterium gas is injected into an H-mode plasma, reduces P[sub div] by factors of 3-5 in DIII-D.A key element in the physics model of PDD operation is that carbon radiation near the X-point dissipates the energy flowing in the scrape-off-layer (SOL) before it enters the divertor[2]. This allows the divertor temperature to be low, density to be high and thereby reduces the heat flux and ion particle flux to the targets both by reduced recycling and increased recombination. Previous line integrated SPRED measurements[3] and computer simulations indicated that the 155 nm[Delta]n= 0 transition of C[sup 3+] was the main power radiator from carbon during PDD operation. This paper presents the first 2D profiles of 155 nm CIV emission in any tokamak divertor. The images were obtained on DIII-D with a new tangentially viewing VUV camera[4] and established image reconstruction techniques[5]. The discharges were lower single null configurations with, I[sub p]= 1.75 MA, B[sub T]= 2.1[Tau], q[sub 95]= 3.2, P[sub inj]= 9 MW, [kappa]= 1.9 and the[nabla]B drift toward the lower divertor. After establishing an ELMing H-mode with neutral beam injection, deuterium gas was injected at 17 Pa m[sup 3]/s (130 T[ell]/s) to increase the divertor density and produce a transition to PDD operation. A practical discharge scenario is given in Ref.[2].
Download or read book Visible Spectroscopy in the DIII D Divertor written by and published by . This book was released on 1996 with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt: Spectroscopy measurements in the DIII-D divertor have been carried out with a survey spectrometer which provides simultaneous registration of the visible spectrum over the region 400--900 nm with a resolution of 0.2 nm. Broad spectral coverage is achieved through use of a fiberoptic transformer assembly to map the curved focal plane of a fast (f/3) Rowland-circle spectrograph into a rastered format on the rectangular sensor area of a two-dimensional CCD camera. Vertical grouping of pixels during CCD readout integrates the signal intensity over the height of each spectral segment in the rastered image, minimizing readout time. For the full visible spectrum, readout time is 50 ms. Faster response time (
Download or read book Analysis of Particle Flow in the DIII D SOL and Divertor written by and published by . This book was released on 1995 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: The scrape-off layer (SOL) and divertor plasma in the DEEI-D tokamak has been modeled using the 2-D fluid code UEDGE. The resulting simulated plasmas are compared in detail with the numerous diagnostics available on the device. Good agreement is obtained between the experimental measurements and the simulations when relatively small values of the assumed anomalous perpendicular transport coefficients are used. We use a purely diffusive model for perpendicular transport, with transport coefficients which are constant in space. The value of each of these transport coefficients is varied in the simulation to match the measured upstream density and temperature profiles. The resulting plasma parameters are then compared with all other diagnostics which measure parameters at various poloidal locations in the SOL.
Download or read book Plasma Surface Interactions in Controlled Fusion Devices written by and published by . This book was released on 1978 with total page 658 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sputtering by Particle Bombardment written by Rainer Behrisch and published by Springer Science & Business Media. This book was released on 2007-07-26 with total page 527 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a long-needed survey of new results. Especially welcome is a new summary of the measured and calculated sputtering yields with an algebraic approximation formula for the energy and angular dependence of the yields, which is useful for researchers who need sputtering yields for physics research or applied problems. The book offers a critical review of computational methods for calculating sputtering yields and also includes molecular dynamics calculations.
Download or read book Magnetic Fusion Technology written by Thomas J. Dolan and published by Springer Science & Business Media. This book was released on 2014-02-10 with total page 816 pages. Available in PDF, EPUB and Kindle. Book excerpt: Magnetic Fusion Technology describes the technologies that are required for successful development of nuclear fusion power plants using strong magnetic fields. These technologies include: • magnet systems, • plasma heating systems, • control systems, • energy conversion systems, • advanced materials development, • vacuum systems, • cryogenic systems, • plasma diagnostics, • safety systems, and • power plant design studies. Magnetic Fusion Technology will be useful to students and to specialists working in energy research.
Download or read book Progress in Fine Particle Plasmas written by Tetsu Mieno and published by BoD – Books on Demand. This book was released on 2020-08-26 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the field of plasma physics, plasmas (including charged fine particles) have been actively studied for more than 40 years, and special features of wave phenomena, self-organizations of the particles, potential formations, fluid-like motions of the particles, generations of fine particles in the plasmas, etc. have been investigated. Here, these plasmas are called “fine particle plasmas”, which are also called “dusty plasmas” and “complex plasmas”. This book intends to provide the reader with the recent progress of studies of fine particle plasmas from the viewpoints of wide and interdisciplinary directions, such as self-organized fine particles, Coulomb crystal formation, behaviors of fine particles, their stability, and syntheses of nano-sized particles in reactive plasmas. Further, the phenomena of dense grain particles and the effects of massive neutrinos in galaxy clustering are included.
Download or read book Principles of Plasma Diagnostics written by I. H. Hutchinson and published by Cambridge University Press. This book was released on 2005-07-14 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a systematic introduction to the physics of plasma diagnostics measurements. It develops from first principles the concepts needed to plan, execute and interpret plasma measurements, making it a suitable book for graduate students and professionals with little plasma physics background. The book will also be a valuable reference for seasoned plasma physicists, both experimental and theoretical, as well as those with an interest in space and astrophysical applications. This second edition is thoroughly revised and updated, with new sections and chapters covering recent developments in the field.
Download or read book Making Choices about Hydrogen written by Lynn Krieger Mytelka and published by IDRC. This book was released on 2008 with total page 416 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the mid-1990s, the emergence of a hydrogen economy and the speed with which it will arrive have been vigorously debated. As a disruptive technology, dominant designs for the production, storage and distribution of hydrogen have not yet been established. Neither have performance characteristics been achieved to compete with the existing combustion engine, though the efficiency and durability of hydrogen fuel cells are improving. This publication highlights the uncertainties involved in making choices about hydrogen and fuel cells in planning the development policies on national energy, environment and transport sector.--Publisher's description.
Download or read book On the Edge of Magnetic Fusion Devices written by Sergei Krasheninnikov and published by Springer. This book was released on 2021-09-09 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews the current state of understanding concerning edge plasma, which bridges hot fusion plasma, with a temperature of roughly one million degrees Kelvin with plasma-facing materials, which have melting points of only a few thousand degrees Kelvin. In a fact, edge plasma is one of the keys to solution for harnessing fusion energy in magnetic fusion devices. The physics governing the processes at work in the edge plasma involves classical and anomalous transport of multispecies plasma, neutral gas dynamics, atomic physics effects, radiation transport, plasma-material interactions, and even the transport of plasma species within the plasma-facing materials. The book starts with simple physical models, then moves on to rigorous theoretical considerations and state-of-the-art simulation tools that are capable of capturing the most important features of the edge plasma phenomena. The authors compare the conclusions arising from the theoretical and computational analysis with the available experimental data. They also discuss the remaining gaps in their models and make projections for phenomena related to edge plasma in magnetic fusion reactors.
Download or read book Powders and Bulk Solids written by Dietmar Schulze and published by Springer Nature. This book was released on 2021-09-02 with total page 625 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book concentrates on powder flow properties, their measurement and applications. These topics are explained starting from the interactions between individual particles up to the design of silos. A wide range of problems are discussed – such as flow obstructions, segregation, and vibrations. The goal is to provide a deeper understanding of the powder flow, and to show practical solutions.
