Download or read book Numerical Simulation of Delamination Growth in Composite Materials written by P. P. Camanho and published by . This book was released on 2001 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: The use of decohesion elements for the simulation of delamination in composite materials is reviewed. The test methods available to measure the interfacial fracture toughness used in the formulation of decohesion elements are described initially. After a brief presentation of the virtual crack technique most widely used to simulate delamination growth, the formulation of interfacial decohesion elements is described. Problems related with decohesion element constitutive equations, mixed-mode crack growth, element numerical integration and solution procedures are discussed. Based on these investigations, it is concluded that the use of interfacial decohesion elements is a promising technique that avoids the need for a pre-existing crack and pre-interfacial decohesion elements is a promising technique that avoids the need for a pre-existing crack and predefined crack paths, and that these elements can be used to simulate both delamination onset and growth.
Download or read book Numerical Simulation of Delamination Growth in Composite Materials written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-16 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: The use of decohesion elements for the simulation of delamination in composite materials is reviewed. The test methods available to measure the interfacial fracture toughness used in the formulation of decohesion elements are described initially. After a brief presentation of the virtual crack closure technique, the technique most widely used to simulate delamination growth, the formulation of interfacial decohesion elements is described. Problems related with decohesion element constitutive equations, mixed-mode crack growth, element numerical integration and solution procedures are discussed. Based on these investigations, it is concluded that the use of interfacial decohesion elements is a promising technique that avoids the need for a pre-existing crack and pre-defined crack paths, and that these elements can be used to simulate both delamination onset and growth. Camanho, P. P. and Davila, C. G. and Ambur, D. R. Langley Research Center NASA/TP-2001-211041, L-18101, NAS 1.60:211041
Download or read book Numerical Simulation of Delamination Growth in Composite Materials Nasa tp 2001 211041 Oct 11 2001 written by United States. National Aeronautics and Space Administration and published by . This book was released on 2004* with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Virtual Crack Closure Technique History Approach and Applications written by Ronald Krueger and published by . This book was released on 2002 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: An overview of the virtual crack closure technique is presented. The approach used is discussed, the history summarized, and insight into its applications provided. Equations for two-dimensional quadrilateral elements with linear and quadratic shape functions are given. Formula for applying the technique in conjuction with three-dimensional solid elements as well as plate/shell elements are also provided. Necessary modifications for the use of the method with geometrically nonlinear finite element analysis and corrections required for elements at the crack tip with different lengths and widths are discussed. The problems associated with cracks or delaminations propagating between different materials are mentioned briefly, as well as a strategy to minimize these problems. Due to an increased interest in using a fracture mechanics based approach to assess the damage tolerance of composite structures in the design phase and during certification, the engineering problems selected as examples and given as references focus on the application of the technique to components made of composite materials.
Download or read book Mixed Mode Decohesion Finite Elements for the Simulation of Delamination in Composite Materials written by and published by . This book was released on 2002 with total page 44 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Numerical Modelling of Failure in Advanced Composite Materials written by Pedro P. Camanho and published by Woodhead Publishing. This book was released on 2015-08-07 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Numerical Modelling of Failure in Advanced Composite Materials comprehensively examines the most recent analysis techniques for advanced composite materials. Advanced composite materials are becoming increasingly important for lightweight design in aerospace, wind energy, and mechanical and civil engineering. Essential for exploiting their potential is the ability to reliably predict their mechanical behaviour, particularly the onset and propagation of failure. Part One investigates numerical modeling approaches to interlaminar failure in advanced composite materials. Part Two considers numerical modelling approaches to intralaminar failure. Part Three presents new and emerging advanced numerical algorithms for modeling and simulation of failure. Part Four closes by examining the various engineering and scientific applications of numerical modeling for analysis of failure in advanced composite materials, such as prediction of impact damage, failure in textile composites, and fracture behavior in through-thickness reinforced laminates. Examines the most recent analysis models for advanced composite materials in a coherent and comprehensive manner Investigates numerical modelling approaches to interlaminar failure and intralaminar failure in advanced composite materials Reviews advanced numerical algorithms for modeling and simulation of failure Examines various engineering and scientific applications of numerical modelling for analysis of failure in advanced composite materials
Download or read book Delamination Behaviour of Composites written by Srinivasan Sridharan and published by Elsevier. This book was released on 2008-10-21 with total page 787 pages. Available in PDF, EPUB and Kindle. Book excerpt: Given such advantages as low weight compared to strength and toughness, laminated composites are now used in a wide range of applications. Their increasing use has underlined the need to understand their principal mode of failure, delamination. This important book reviews key research in understanding and preventing delamination. The first part of the book reviews general issues such as the role of fracture mechanics in understanding delamination, design issues and ways of testing delamination resistance. Part two describes techniques for detecting and characterising delamination such as piezoelectric sensors, the use of lamb waves and acoustic emission techniques. The next two sections of the book discuss ways of studying and modelling delamination behaviour. The final part of the book reviews research on delamination behaviour in particular conditions such as shell and sandwich structures, z-pin bridging and resin bonding. With its distinguished editor and international team of contributors, Delamination behaviour of composites is a standard reference for all those researching laminated composites and using them in such diverse applications as microelectronics, aerospace, marine, automotive and civil engineering. Reviews the role of fracture mechanics in understanding delamination, design issues and ways of testing delamination resistance Discuss ways of studying and modelling delamination behaviour A standard reference for all those researching laminated composites
Download or read book Delamination Buckling of Composite Materials written by L. Kachanov and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 101 pages. Available in PDF, EPUB and Kindle. Book excerpt: LIOn Delamination of Laminated Composites (a) Fiber-Reinforced Composites Considerable technological advances in the production of high-strength fibers (graphite, boron, etc.) have led to a wide use of light high-strength composite materials (graphite epoxy, boron-epoxy, etc.). It is expedient, to make thin walled composite rods, plates, and shells from such materials. Plates can be made by bonding a set of unidirectional thin fiber layers, Fig.l.l. Such plates are orthotropic, as a rule. A random short-fiber composite is shown in Fig. 1.2. Fiber-reinforced composites are widely used in thin-walled aircraft structures because of their specific high strength. For example, the graphite-epoxy composite is characterized by a unidirectional tensile strength of 1.4 GPa while the density is 1.6 Mg/rrt? . For comparison, we may take a steel (steel 4340) whose corresponding properties are identified by values like 1.2 GPa and 7.8 Mg/rrt? . 1. INTRODUCTION Figure 1.1 2 1.1. On Delamination of Laminated Composites Figure 1.2 3 1. INTRODUCTION It is characteristic for laminated plastic material to possess a fairly low bonding. Therefore, low-velocity impacts and defects in manufacturing lead to local delamination. (b) Linear Problems of Delamination Buckling Delamination can significantly reduce the compressive strength and stiffness of the laminate. Local delamination can be considered as a crack in the bond. Under buckling there appears a high interlaminate stress at the crack edge that leads to a spreading of the crack. Delamination growth can lead to structural instability.
Download or read book Damage Growth in Aerospace Composites written by Aniello Riccio and published by Springer. This book was released on 2015-01-07 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents novel methods for the simulation of damage evolution in aerospace composites that will assist in predicting damage onset and growth and thus foster less conservative designs which realize the promised economic benefits of composite materials. The presented integrated numerical/experimental methodologies are capable of taking into account the presence of damage and its evolution in composite structures from the early phases of the design (conceptual design) through to the detailed finite element method analysis and verification phase. The book is based on the GARTEUR Research Project AG-32, which ran from 2007 to 2012, and documents the main results of that project. In addition, the state of the art in European projects on damage evolution in composites is reviewed. While the high specific strength and stiffness of composite materials make them suitable for aerospace structures, their sensitivity to damage means that designing with composites is a challenging task. The new approaches described here will prove invaluable in meeting that challenge.
Download or read book Multiscale Modeling and Simulation of Composite Materials and Structures written by Young Kwon and published by Springer Science & Business Media. This book was released on 2007-12-04 with total page 634 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the state-of-the-art in multiscale modeling and simulation techniques for composite materials and structures. It focuses on the structural and functional properties of engineering composites and the sustainable high performance of components and structures. The multiscale techniques can be also applied to nanocomposites which are important application areas in nanotechnology. There are few books available on this topic.
Download or read book Damage and Fracture of Composite Materials and Structures written by Mohd Nasir Tamin and published by Springer Science & Business Media. This book was released on 2012-01-03 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: This monograph presents recent research findings on fracture properties and behavior of the composites, and their damage and cracking process under both quasi-static and impact loading conditions. Theoretical treatment, experimental investigation and numerical simulation aspects of the mechanics of composites, including sandwich structures are included.
Download or read book Delamination Growth in Composite Materials written by and published by . This book was released on 1986 with total page 218 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mixed Mode Decohesion Finite Elements for the Simulation of Delamination in Composite Materials written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-06-03 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt: A new decohesion element with mixed-mode capability is proposed and demonstrated. The element is used at the interface between solid finite elements to model the initiation and non-self-similar growth of delaminations. A single relative displacement-based damage parameter is applied in a softening law to track the damage state of the interface and to prevent the restoration of the cohesive state during unloading. The softening law for mixed-mode delamination propagation can be applied to any mode interaction criterion such as the two-parameter power law or the three-parameter Benzeggagh-Kenane criterion. To demonstrate the accuracy of the predictions and the irreversibility capability of the constitutive law, steady-state delamination growth is simulated for quasistatic loading-unloading cycles of various single mode and mixed-mode delamination test specimens.Camanho, Pedro P. and Davila, Carlos G.Langley Research CenterDAMAGE; DELAMINATING; FRACTURE MECHANICS; COMPOSITE MATERIALS; MATHEMATICAL MODELS; FINITE ELEMENT METHOD; KINEMATICS; EPOXY COMPOUNDS
Download or read book Defects and Damage in Composite Materials and Structures written by Rikard Benton Heslehurst and published by CRC Press. This book was released on 2014-04-21 with total page 206 pages. Available in PDF, EPUB and Kindle. Book excerpt: The advantages of composite materials include a high specific strength and stiffness, formability, and a comparative resistance to fatigue cracking and corrosion. However, not forsaking these advantages, composite materials are prone to a wide range of defects and damage that can significantly reduce the residual strength and stiffness of a structu
Download or read book Finite Element Analysis of Composite Materials using AbaqusTM written by Ever J. Barbero and published by CRC Press. This book was released on 2013-04-18 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt: Developed from the author's graduate-level course on advanced mechanics of composite materials, Finite Element Analysis of Composite Materials with Abaqus shows how powerful finite element tools address practical problems in the structural analysis of composites. Unlike other texts, this one takes the theory to a hands-on level by actually solving
Download or read book Analysis of Instability related Growth of a Through width Delamination written by J. D. Whitcomb and published by . This book was released on 1984 with total page 122 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Scaled Boundary Finite Element Method written by Chongmin Song and published by John Wiley & Sons. This book was released on 2018-06-19 with total page 504 pages. Available in PDF, EPUB and Kindle. Book excerpt: An informative look at the theory, computer implementation, and application of the scaled boundary finite element method This reliable resource, complete with MATLAB, is an easy-to-understand introduction to the fundamental principles of the scaled boundary finite element method. It establishes the theory of the scaled boundary finite element method systematically as a general numerical procedure, providing the reader with a sound knowledge to expand the applications of this method to a broader scope. The book also presents the applications of the scaled boundary finite element to illustrate its salient features and potentials. The Scaled Boundary Finite Element Method: Introduction to Theory and Implementation covers the static and dynamic stress analysis of solids in two and three dimensions. The relevant concepts, theory and modelling issues of the scaled boundary finite element method are discussed and the unique features of the method are highlighted. The applications in computational fracture mechanics are detailed with numerical examples. A unified mesh generation procedure based on quadtree/octree algorithm is described. It also presents examples of fully automatic stress analysis of geometric models in NURBS, STL and digital images. Written in lucid and easy to understand language by the co-inventor of the scaled boundary element method Provides MATLAB as an integral part of the book with the code cross-referenced in the text and the use of the code illustrated by examples Presents new developments in the scaled boundary finite element method with illustrative examples so that readers can appreciate the significant features and potentials of this novel method—especially in emerging technologies such as 3D printing, virtual reality, and digital image-based analysis The Scaled Boundary Finite Element Method: Introduction to Theory and Implementation is an ideal book for researchers, software developers, numerical analysts, and postgraduate students in many fields of engineering and science.
