Download or read book Numerical modeling and simulation of particulate fouling on structured heat transfer surfaces using multiphase Eulerian Lagrangian LES written by Robert Kasper and published by Cuvillier Verlag. This book was released on 2021-04-30 with total page 178 pages. Available in PDF, EPUB and Kindle. Book excerpt: Durch die gezielte Strukturierung von wärmeübertragenden Oberflächen, wie beispielsweise durch Dellen oder Rippen, kann die örtliche Turbulenz und damit die thermische Durchmischung gesteigert werden. Dies kann die Effizienz von Wärmeübertragern oder Bauteilkühlsystemen erheblich erhöhen. Derartige Oberflächenstrukturrierungen begünstigen jedoch das Partikelfouling, daher die Ablagerung suspendierter Partikel, wie z.B. Sand, Schlamm oder Korrosionsprodukte. Gegenstand dieser Arbeit ist die Entwicklung eines universellen, numerischen CFD-Verfahrens zur Vorhersage des partikulären Foulings auf strukturierten Oberflächen, speziell Dellenoberflächen. Das entwickelte Verfahren basiert auf einer Kombination des Lagrangian-Particle-Trackings zur Beschreibung der dispersen Phase (Foulingpartikel), sowie räumlich und zeitlich aufgelöster Large-Eddy Simulation für die Berechnung der kontinuierlichen Phasen (Trägerfluid). Dieses Vorgehen ermöglicht nicht nur die Auswertung der infolge der Partikelablagerungen verminderten thermo-hydraulischen Effizienz, sondern auch die Untersuchung der Wechselwirkungen zwischen turbulenten Strömungsstrukturen und dem partikulärem Fouling. Dadurch kann gezeigt werden, dass die Verwendung von sphärischen Dellen als Oberflächenstrukturen nicht nur aus thermo-hydraulischer Sicht die optimale Wahl darstellt, sondern auch eine substantielle Verminderung des Partikelfoulings begünstigt. The application of structured heat transfer surfaces, such as dimples or ribs, increase the local turbulence and thus thermal mixing. This can improve the efficiency of heat exchangers or cooling systems significantly. However, structured surfaces are known to promote particulate fouling, hence the unwanted accumulation and deposition of suspended particles (e.g., silt, sludge or iron oxide). The scope of this work is the development of a universal numerical CFD method for the prediction of particulate fouling, especially on dimpled surfaces. The proposed approach is based on a combination of the Lagrangian point-particle tracking for the description of the disperse phase (fouling particles), and spatially and temporally resolved large-eddy simulations for the calculation of the continuous phase (carrier fluid). This approach allows not only the evaluation of the reduced thermo-hydraulic efficiency due to particle deposition, but also the investigation of the interaction between turbulent flow structures and the particulate fouling. It can be shown that the usage of spherical dimples as surface structures is not only the optimal choice from a thermo-hydraulic point of view, but also favors a substantial reduction of particulate fouling.
Download or read book OpenFOAM written by J. Miguel Nóbrega and published by Springer. This book was released on 2019-01-24 with total page 527 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains selected papers of the 11th OpenFOAM® Workshop that was held in Guimarães, Portugal, June 26 - 30, 2016. The 11th OpenFOAM® Workshop had more than 140 technical/scientific presentations and 30 courses, and was attended by circa 300 individuals, representing 180 institutions and 30 countries, from all continents. The OpenFOAM® Workshop provided a forum for researchers, industrial users, software developers, consultants and academics working with OpenFOAM® technology. The central part of the Workshop was the two-day conference, where presentations and posters on industrial applications and academic research were shown. OpenFOAM® (Open Source Field Operation and Manipulation) is a free, open source computational toolbox that has a larger user base across most areas of engineering and science, from both commercial and academic organizations. As a technology, OpenFOAM® provides an extensive range of features to solve anything from complex fluid flows involving chemical reactions, turbulence and heat transfer, to solid dynamics and electromagnetics, among several others. Additionally, the OpenFOAM technology offers complete freedom to customize and extend its functionalities.
Download or read book Comprehensive Dissertation Index written by and published by . This book was released on 1989 with total page 1116 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Multiphase Flow Analysis Using Population Balance Modeling written by Guan Heng Yeoh and published by Butterworth-Heinemann. This book was released on 2013-08-19 with total page 385 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by leading multiphase flow and CFD experts, this book enables engineers and researchers to understand the use of PBM and CFD frameworks. Population balance approaches can now be used in conjunction with CFD, effectively driving more efficient and effective multiphase flow processes. Engineers familiar with standard CFD software, including ANSYS-CFX and ANSYS–Fluent, will be able to use the tools and approaches presented in this book in the effective research, modeling and control of multiphase flow problems. - Builds a complete understanding of the theory behind the application of population balance models and an appreciation of the scale-up of computational fluid dynamics (CFD) and population balance modeling (PBM) to a variety of engineering and industry applications in chemical, pharmaceutical, energy and petrochemical sectors - The tools in this book provide the opportunity to incorporate more accurate models in the design of chemical and particulate based multiphase processes - Enables readers to translate theory to practical use with CFD software
Download or read book 1D and Multi D Modeling Techniques for IC Engine Simulation written by Angelo Onorati and published by SAE International. This book was released on 2020-04-06 with total page 552 pages. Available in PDF, EPUB and Kindle. Book excerpt: 1D and Multi-D Modeling Techniques for IC Engine Simulation provides a description of the most significant and recent achievements in the field of 1D engine simulation models and coupled 1D-3D modeling techniques, including 0D combustion models, quasi-3D methods and some 3D model applications.
Download or read book Bubbly Flows written by Martin Sommerfeld and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book summarises the outcom of a priority research programme: 'Analysis, Modelling and Computation of Multiphase Flows'. The results of 24 individual research projects are presented. The main objective of the research programme was to provide a better understanding of the physical basis for multiphase gas-liquid flows as they are found in numerous chemical and biochemical reactors. The research comprises steady and unsteady multiphase flows in three frequently found reactor configurations, namely bubble columns without interiors, airlift loop reactors, and aerated stirred vessels. For this purpose new and improved measurement techniques were developed. From the resulting knowledge and data, new and refined models for describing the underlying physical processes were developed, which were used for the establishment and improvement of analytic as well as numerical methods for predicting multiphase reactors. Thereby, the development, lay-out and scale-up of such processes should be possible on a more reliable basis.
Download or read book Heat Transfer in Polymer Composite Materials written by Nicolas Boyard and published by John Wiley & Sons. This book was released on 2016-03-28 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses general information, good practices and examples about thermo-physical properties, thermo-kinetic and thermo-mechanical couplings, instrumentation in thermal science, thermal optimization and infrared radiation.
Download or read book Fouling of Heat Exchangers written by T.R. Bott and published by Elsevier. This book was released on 1995-04-13 with total page 547 pages. Available in PDF, EPUB and Kindle. Book excerpt: This unique and comprehensive text considers all aspects of heat exchanger fouling from the basic science of how surfaces become fouled to very practical ways of mitigating the problem and from mathematical modelling of different fouling mechanisms to practical methods of heat exchanger cleaning. The problems that restrict the efficient operation of equipment are described and the costs, some of them hidden costs, that are associated with the fouling of heat exchangers are discussed. Some simple concepts and models of the fouling processes are presented as part of the introduction to the subject.Advice on the selection, design, installation and commissioning of heat exchangers to minimise fouling is given. A large part of the text is devoted to the use of chemical and other additives to reduce or eliminate the problem of fouling. Another large section is designed to give information on both on-line and off-line cleaning of heat exchangers. One of the difficulties faced by designers and operators of heat exchangers is anticipating the likely extent of fouling problems to be encountered with different flow streams. Another large section addresses the question and describes methods that have been used in attempting to define fouling potential. The book concludes with a chapter on how fouling information can be obtained using plant data, field tests and laboratory studies.
Download or read book Process Modelling and Simulation written by César de Prada and published by MDPI. This book was released on 2019-09-23 with total page 298 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since process models are nowadays ubiquitous in many applications, the challenges and alternatives related to their development, validation, and efficient use have become more apparent. In addition, the massive amounts of both offline and online data available today open the door for new applications and solutions. However, transforming data into useful models and information in the context of the process industry or of bio-systems requires specific approaches and considerations such as new modelling methodologies incorporating the complex, stochastic, hybrid and distributed nature of many processes in particular. The same can be said about the tools and software environments used to describe, code, and solve such models for their further exploitation. Going well beyond mere simulation tools, these advanced tools offer a software suite built around the models, facilitating tasks such as experiment design, parameter estimation, model initialization, validation, analysis, size reduction, discretization, optimization, distributed computation, co-simulation, etc. This Special Issue collects novel developments in these topics in order to address the challenges brought by the use of models in their different facets, and to reflect state of the art developments in methods, tools and industrial applications.
Download or read book Heat Transfer in Condensation and Boiling written by Karl Stephan and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: I welcome the opportunity to have my book translated, because of the great emphasis on two-phase flow and heat transfer in the English-speaking world, as related to research, university education, and industrial practice. The 1988 Springer-Verlag edition of "Warmeiibergang beim Kondensieren und beim Sieden" has been enlarged to include additional material on falling film evaporation (Chapter 12) and pressure drop in two-phase flow (Chapter 13). Minor errors in the original text have also been corrected. I would like to express my sincere appreciation to Professor Green, Asso ciate Professor of German at Rensselaer, for his excellent translation and co operation. My thanks go also to Professor Bergles for his close attention to technical and linguistic details. He carefully read the typescript and made many comments and suggestions that helped to improve the manuscript. I hope that the English edition will meet with' a favorable reception and contribute to better understanding and to progress in the field of heat transfer in condensation and boiling. February 1992 K. Stephan Preface to the German-Language Edition This book is a continuation of the series "Heat and Mass Transfer" edited by U. Grigull, in which three volumes have already been published. Its aim is to acquaint students and practicing engineers with heat transfer during condensa tion and boiling, and is intended primarily for students and engineers in mechanical, chemical, electrical, and industrial processing engineering.
Download or read book Two Phase Flow written by Cl Kleinstreuer and published by Routledge. This book was released on 2017-11-01 with total page 472 pages. Available in PDF, EPUB and Kindle. Book excerpt: This graduate text provides a unified treatment of the fundamental principles of two-phase flow and shows how to apply the principles to a variety of homogeneous mixture as well as separated liquid-liquid, gas-solid, liquid-solid, and gas-liquid flow problems, which may be steady or transient, laminar or turbulent.Each chapter contains several sample problems, which illustrate the outlined theory and provide approaches to find simplified analytic descriptions of complex two-phase flow phenomena.This well-balanced introductory text will be suitable for advanced seniors and graduate students in mechanical, chemical, biomedical, nuclear, environmental and aerospace engineering, as well as in applied mathematics and the physical sciences. It will be a valuable reference for practicing engineers and scientists. A solutions manual is available to qualified instructors.
Download or read book VDI Heat Atlas written by VDI Gesellschaft and published by Springer Science & Business Media. This book was released on 2010-07-21 with total page 1608 pages. Available in PDF, EPUB and Kindle. Book excerpt: For more than 50 years, the Springer VDI Heat Atlas has been an indispensable working means for engineers dealing with questions of heat transfer. Featuring 50% more content, this new edition covers most fields of heat transfer in industrial and engineering applications. It presents the interrelationships between basic scientific methods, experimental techniques, model-based analysis and their transfer to technical applications.
Download or read book Fouling Science and Technology written by L. Melo and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 720 pages. Available in PDF, EPUB and Kindle. Book excerpt: The fouling of heat exchangers, reactors and catalysts remains one of the most urgent problems facing the process industries. Over the past ten years there has been limited research and investigation into the underlying mechanisms which give rise to this problem. For convenience, particularly in heat exchanger technology, the mechanisms involved have been subdivided into different subject areas. It is often the situation that individuals or groups of workers have concentra ted efforts in one or two of these specialist areas and there is a need to integrate the ideas across the whole spectrum of the subject. In addition, topics such as adhesion and surface phenomena have not been properly taken into account up till now in the assessment of the fouling processes. For this reason it was considered essential that the recognised experts from around the world, who are actively concerned with research, development and design in the fieId, should meet and exchange ideas and experience. Such a meeting was held at Alvor, Portugal, in May 1987, sponsored by the NATO Advanced St~dy Institutes Programme. In order to obtain a common basis for the work of the Advanced Study Institute, the whole technological field was reviewed right from the basic concepts to the frontiers of present knowledge. Each invited contributor was asked to make an overall presentation covering his or her area of expertise.
Download or read book Heat Transfer written by Adrian Bejan and published by John Wiley & Sons. This book was released on 2022-04-05 with total page 612 pages. Available in PDF, EPUB and Kindle. Book excerpt: HEAT TRANSFER Provides authoritative coverage of the fundamentals of heat transfer, written by one of the most cited authors in all of Engineering Heat Transfer presents the fundamentals of the generation, use, conversion, and exchange of heat between physical systems. A pioneer in establishing heat transfer as a pillar of the modern thermal sciences, Professor Adrian Bejan presents the fundamental concepts and problem-solving methods of the discipline, predicts the evolution of heat transfer configurations, the principles of thermodynamics, and more. Building upon his classic 1993 book Heat Transfer, the author maintains his straightforward scientific approach to teaching essential developments such as Fourier conduction, fins, boundary layer theory, duct flow, scale analysis, and the structure of turbulence. In this new volume, Bejan explores topics and research developments that have emerged during the past decade, including the designing of convective flow and heat and mass transfer, the crucial relationship between configuration and performance, and new populations of configurations such as tapered ducts, plates with multi-scale features, and dendritic fins. Heat Transfer: Evolution, Design and Performance: Covers thermodynamics principles and establishes performance and evolution as fundamental concepts in thermal sciences Demonstrates how principles of physics predict a future with economies of scale, multi-scale design, vascularization, and hierarchical distribution of many small features Explores new work on conduction architecture, convection with nanofluids, boiling and condensation on designed surfaces, and resonance of natural circulation in enclosures Includes numerous examples, problems with solutions, and access to a companion website Heat Transfer: Evolution, Design and Performance is essential reading for undergraduate and graduate students in mechanical and chemical engineering, and for all engineers, physicists, biologists, and earth scientists.
Download or read book Thermal Spray Fabrication of Heat Transfer Surfaces and Devices written by Andre McDonald and published by Elsevier. This book was released on 2021-03-01 with total page 416 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermal Spray Fabrication of Heat Transfer Surfaces and Devices reviews the current state of research on select processes for the development of coatings-based heat transfer surfaces and devices, focusing on materials selection, fabrication processes and materials characterization. Analytical modeling and experiments aimed at quantifying the performance of heat transfer surfaces and devices are presented, along with case studies that reinforce the outcomes of analytical models. The included information helps guide readers to industrial situations in which the coatings or devices may be applied. Describes thermal-sprayed coatings in terms of their development as heat transfer surfaces or devices Provides predictive models for the thermal performance of surfaces or devices Presents case studies that describe potential, practical situations in which coatings or devices may be applied
Download or read book Mass Transfer written by Koichi Asano and published by John Wiley & Sons. This book was released on 2007-09-24 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: This didactic approach to the principles and modeling of mass transfer as it is needed in modern industrial processes is unique in combining a step-by-step introduction to all important fundamentals with the most recent applications. Based upon the renowned author's successful new modeling method as used for the O-18 process, the exemplary exercises included in the text are fact-proven, taken directly from existing chemical plants. Fascinating reading for chemists, graduate students, chemical and process engineers, as well as thermodynamics physicists.
Download or read book Particles Bubbles Drops written by Efstathios Michaelides and published by World Scientific. This book was released on 2006 with total page 425 pages. Available in PDF, EPUB and Kindle. Book excerpt: The field of multiphase flows has grown by leaps and bounds in the last thirty years and is now regarded as a major discipline. Engineering applications, products and processes with particles, bubbles and drops have consistently grown in number and importance. An increasing number of conferences, scientific fora and archived journals are dedicated to the dissemination of information on flow, heat and mass transfer of fluids with particles, bubbles and drops. Numerical computations and "thought experiments" have supplemented most physical experiments and a great deal of the product design and testing processes. The literature on computational fluid dynamics with particles, bubbles and drops has grown at an exponential rate, giving rise to new results, theories and better understanding of the transport processes with particles, bubbles and drops. This book captures and summarizes all these advances in a unified, succinct and pedagogical way. Contents: Fundamental Equations and Characteristics of Particles, Bubbles and Drops; Low Reynolds Number Flows; High Reynolds Number Flows; Non-Spherical Particles, Bubbles and Drops; Effects of Rotation, Shear and Boundaries; Effects of Turbulence; Electro-Kinetic, Thermo-Kinetic and Porosity Effects; Effects of Higher Concentration and Collisions; Molecular and Statistical Modeling; Numerical Methods-CFD. Key Features Summarizes the recent important results in the theory of transport processes of fluids with particles, bubbles and drops Presents the results in a unified and succinct way Contains more than 600 references where an interested reader may find details of the results Makes connections from all theories and results to physical and engineering applications Readership: Researchers, practicing engineers and physicists that deal with any aspects of Multiphase Flows. It will also be of interest to academics and researchers in the general fields of mechanical and chemical engineering.
