Download or read book Numerical and Experimental Studies on Combustion Engines and Vehicles written by Paweł Woś and published by BoD – Books on Demand. This book was released on 2020-11-26 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt: The matters discussed and presented in the chapters of this book cover a wide spectrum of topics and research methods commonly used in the field of engine combustion technology and vehicle functional systems. This book contains the results of both computational analyses and experimental studies on jet and reciprocating combustion engines as well heavy-duty onroad vehicles. Special attention is devoted to research and measures toward preventing the emission of harmful exhaust components, reducing fuel consumption or using unconventional methods of engine fueling or using renewable and alternative fuels in different applications. Some technical improvements in design and control of vehicle systems are also presented.
Download or read book Automotive Spark Ignited Direct Injection Gasoline Engines written by F. Zhao and published by Elsevier. This book was released on 2000-02-08 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt: The process of fuel injection, spray atomization and vaporization, charge cooling, mixture preparation and the control of in-cylinder air motion are all being actively researched and this work is reviewed in detail and analyzed. The new technologies such as high-pressure, common-rail, gasoline injection systems and swirl-atomizing gasoline fuel injections are discussed in detail, as these technologies, along with computer control capabilities, have enabled the current new examination of an old objective; the direct-injection, stratified-charge (DISC), gasoline engine. The prior work on DISC engines that is relevant to current GDI engine development is also reviewed and discussed. The fuel economy and emission data for actual engine configurations have been obtained and assembled for all of the available GDI literature, and are reviewed and discussed in detail. The types of GDI engines are arranged in four classifications of decreasing complexity, and the advantages and disadvantages of each class are noted and explained. Emphasis is placed upon consensus trends and conclusions that are evident when taken as a whole; thus the GDI researcher is informed regarding the degree to which engine volumetric efficiency and compression ratio can be increased under optimized conditions, and as to the extent to which unburned hydrocarbon (UBHC), NOx and particulate emissions can be minimized for specific combustion strategies. The critical area of GDI fuel injector deposits and the associated effect on spray geometry and engine performance degradation are reviewed, and important system guidelines for minimizing deposition rates and deposit effects are presented. The capabilities and limitations of emission control techniques and after treatment hardware are reviewed in depth, and a compilation and discussion of areas of consensus on attaining European, Japanese and North American emission standards presented. All known research, prototype and production GDI engines worldwide are reviewed as to performance, emissions and fuel economy advantages, and for areas requiring further development. The engine schematics, control diagrams and specifications are compiled, and the emission control strategies are illustrated and discussed. The influence of lean-NOx catalysts on the development of late-injection, stratified-charge GDI engines is reviewed, and the relative merits of lean-burn, homogeneous, direct-injection engines as an option requiring less control complexity are analyzed.
Download or read book Particle Image Velocimetry written by Markus Raffel and published by Springer Science & Business Media. This book was released on 2007-08-09 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: This immensely practical guide to PIV provides a condensed, yet exhaustive guide to most of the information needed for experiments employing the technique. This second edition has updated chapters on the principles and extra information on microscopic, high-speed and three component measurements as well as a description of advanced evaluation techniques. What’s more, the huge increase in the range of possible applications has been taken into account as the chapter describing these applications of the PIV technique has been expanded.
Download or read book Diesel Engine Reference Book written by Bernard Challen and published by Butterworth-Heinemann. This book was released on 1999 with total page 712 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference work covering the design and applications of diesel engines of all sizes. The text uses easily understood language and a practical approach to explore aspects of diesel engineering such as thermodynamics modelling, long-term use, applications and condition monitoring.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1994 with total page 892 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mathematical Modeling Computational Intelligence Techniques and Renewable Energy written by Manoj Sahni and published by Springer Nature. This book was released on 2021-02-28 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents new knowledge and recent developments in all aspects of computational techniques, mathematical modeling, energy systems, applications of fuzzy sets and intelligent computing. The book is a collection of best selected research papers presented at the International Conference on “Mathematical Modeling, Computational Intelligence Techniques and Renewable Energy,” organized by the Department of Mathematics, Pandit Deendayal Petroleum University, in association with Forum for Interdisciplinary Mathematics, Institution of Engineers (IEI) – Gujarat and Computer Society of India (CSI) – Ahmedabad. The book provides innovative works of researchers, academicians and students in the area of interdisciplinary mathematics, statistics, computational intelligence and renewable energy.
Download or read book Proceedings of the 7th International Conference on Advances in Energy Research written by Manaswita Bose and published by Springer Nature. This book was released on 2020-10-17 with total page 1639 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents selected papers from the 7th International Conference on Advances in Energy Research (ICAER 2019), providing a comprehensive coverage encompassing all fields and aspects of energy in terms of generation, storage, and distribution. Themes such as optimization of energy systems, energy efficiency, economics, management, and policy, and the interlinkages between energy and environment are included. The contents of this book will be of use to researchers and policy makers alike.
Download or read book Direkteinspritzung im Ottomotor IV written by Ulrich Spicher and published by expert verlag. This book was released on 2003 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modelling Spark Ignition Combustion written by P. A. Lakshminarayanan and published by Springer Nature. This book was released on with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Mixture Formation in Internal Combustion Engines written by Carsten Baumgarten and published by Springer Science & Business Media. This book was released on 2006-09-28 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: A systematic control of mixture formation with modern high-pressure injection systems enables us to achieve considerable improvements of the combustion pr- ess in terms of reduced fuel consumption and engine-out raw emissions. However, because of the growing number of free parameters due to more flexible injection systems, variable valve trains, the application of different combustion concepts within different regions of the engine map, etc., the prediction of spray and m- ture formation becomes increasingly complex. For this reason, the optimization of the in-cylinder processes using 3D computational fluid dynamics (CFD) becomes increasingly important. In these CFD codes, the detailed modeling of spray and mixture formation is a prerequisite for the correct calculation of the subsequent processes like ignition, combustion and formation of emissions. Although such simulation tools can be viewed as standard tools today, the predictive quality of the sub-models is c- stantly enhanced by a more accurate and detailed modeling of the relevant pr- esses, and by the inclusion of new important mechanisms and effects that come along with the development of new injection systems and have not been cons- ered so far. In this book the most widely used mathematical models for the simulation of spray and mixture formation in 3D CFD calculations are described and discussed. In order to give the reader an introduction into the complex processes, the book starts with a description of the fundamental mechanisms and categories of fuel - jection, spray break-up, and mixture formation in internal combustion engines.
Download or read book Automotive Gasoline Direct Injection Engines written by Fuquan Zhao and published by SAE International. This book was released on 2002-05-15 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the latest global technical initiatives in the rapidly progressing area of gasoline direct injection (GDI), spark-ignited gasoline engines and examines the contribution of each process and sub-system to the efficiency of the overall system. Including discussions, data, and figures from many technical papers and proceedings that are not available in the English language, Automotive Gasoline Direct Injection Systems will prove to be an invaluable desk reference for any GDI subject or direct-injection subsystem that is being developed worldwide.
Download or read book Modeling Engine Spray and Combustion Processes written by Gunnar Stiesch and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 293 pages. Available in PDF, EPUB and Kindle. Book excerpt: The utilization of mathematical models to numerically describe the performance of internal combustion engines is of great significance in the development of new and improved engines. Today, such simulation models can already be viewed as standard tools, and their importance is likely to increase further as available com puter power is expected to increase and the predictive quality of the models is constantly enhanced. This book describes and discusses the most widely used mathematical models for in-cylinder spray and combustion processes, which are the most important subprocesses affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic, fluid dynamic and chemical principles are summarized, and then the application of these principles to the in-cylinder processes is ex plained. Different modeling approaches for the each subprocesses are compared and discussed with respect to the governing model assumptions and simplifica tions. Conclusions are drawn as to which model approach is appropriate for a specific type of problem in the development process of an engine. Hence, this book may serve both as a graduate level textbook for combustion engineering stu dents and as a reference for professionals employed in the field of combustion en gine modeling. The research necessary for this book was carried out during my employment as a postdoctoral scientist at the Institute of Technical Combustion (ITV) at the Uni versity of Hannover, Germany and at the Engine Research Center (ERC) at the University of Wisconsin-Madison, USA.
Download or read book Droplets and Sprays written by Saptarshi Basu and published by Springer. This book was released on 2017-12-11 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on droplets and sprays relevant to combustion and propulsion applications. The book includes fundamental studies on the heating, evaporation and combustion of individual droplets and basic mechanisms of spray formation. The contents also extend to the latest analytical, numerical and experimental techniques for investigating the behavior of sprays in devices like combustion engines and gas turbines. In addition, the book explores several emerging areas like interactions between sprays and flames and the dynamic characteristics of spray combustion systems on the fundamental side, as well as the development of novel fuel injectors for specific devices on the application side. Given its breadth of coverage, the book will benefit researchers and professionals alike.
Download or read book Surfactants in Tribology Volume 5 written by Girma Biresaw and published by CRC Press. This book was released on 2017-09-11 with total page 516 pages. Available in PDF, EPUB and Kindle. Book excerpt: Surfactants play a critical role in Tribology controlling friction, wear, and lubricant properties such as emulsification, demulsification, bioresistance, oxidation resistance, rust prevention and corrosion resistance. This is a critical topic for new materials and devices particularly those built at the nanoscale. This newest volume will address tribological properties of cutting fluids, lubricant performance related to steel surfaces, biolubricants, and novel materials and ways to reduce friction and wear. Scientists from industrial research and development (R&D) organizations and academic research teams in Asia, Europe, the Middle East and North America will participate in the work.
Download or read book Liquid Atomization written by L.P. Bayvel and published by Routledge. This book was released on 2019-01-22 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covering the basics of liquid atomization, this book familiarizes readers with the physical processes of liquid atomization, the main types of atomizers and their design, measurements of spray characteristics, experimental investigations of atomizers, and application of atomizers. It demonstrates how to calculate and design atomizers and how to mea
Download or read book Emerging Trends in Mechanical and Industrial Engineering written by Xianguo Li and published by Springer Nature. This book was released on 2023-01-01 with total page 1062 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book presents the select proceedings of the International Conference on Emerging Trends in Mechanical and Industrial Engineering (ICETMIE 2022). It covers the latest trends in the area of mechanical engineering. The broad topics covered in the book are engineering design, industrial and production engineering, Industry 4.0, energy and process engineering, mechatronics, control and robotics, material science, and automotive engineering. The book is useful for students, researchers, and professionals working in the various areas of mechanical engineering.
Download or read book Handbook of Atomization and Sprays written by Nasser Ashgriz and published by Springer Science & Business Media. This book was released on 2011-02-18 with total page 922 pages. Available in PDF, EPUB and Kindle. Book excerpt: Atomization and sprays are used in a wide range of industries: mechanical, chemical, aerospace, and civil engineering; material science and metallurgy; food; pharmaceutical, forestry, environmental protection; medicine; agriculture; meteorology and others. Some specific applications are spray combustion in furnaces, gas turbines and rockets, spray drying and cooling, air conditioning, powdered metallurgy, spray painting and coating, inhalation therapy, and many others. The Handbook of Atomization and Sprays will bring together the fundamental and applied material from all fields into one comprehensive source. Subject areas included in the reference are droplets, theoretical models and numerical simulations, phase Doppler particle analysis, applications, devices and more.
