Download or read book Next Generation Materials for Block Copolymer Lithography written by Michael Joseph Maher and published by . This book was released on 2016 with total page 576 pages. Available in PDF, EPUB and Kindle. Book excerpt: The electronics industry is a trillion dollar industry that has drastically changed everyday life. Advances in lithography have enabled manufacturers to continually shrink the dimensions of microelectronic components, which has resulted in devices that outperform previous generations. Unfortunately, conventional patterning techniques are approaching their physical resolution limits. The ability to economically pattern sub-10 nm features is necessary for the future growth of the industry. Block copolymer self-assembly has emerged as a leading candidate for next generation lithography and nanofabrication because block copolymers self-assemble into periodic nanostructures (e.g. cylinders and lamellae) on a length scale that exceeds the physical limits of optical lithography. However, for block copolymer lithography to be realized, the block copolymer domains need to form sub-10 nm features and display etch resistance for pattern transfer. Additionally, the orientation, alignment, and placement of block copolymer domains must be carefully controlled. This dissertation discusses the synthesis, orientation and alignment of silicon-containing BCPs that are inherently etch resistant and provide access to nanostructures in the sub-10 nm regime. The orientation of domains is controlled by interactions between each block copolymer domain and each interface. Preferential interactions between the block copolymer domains and the either the substrate or air interface lead to a parallel orientation of domains, which is not useful for lithography. Non-preferential (“neutral”) interactions are needed to promote the desired perpendicular orientation. The synthesis of surface treatments and top coats is described, and methods to determine the preferential and non-preferential interactions are reported. Orientation control is demonstrated via rapid thermal annealing between two neutral surfaces. Combining orientation control of block copolymer domains with well established directed self-assembly strategies was used to produce perpendicular domains with long range order. Chapter 1 provides an introduction to lithography and block copolymer self-assembly. Chapter 2 discusses the synthesis of silicon-containing block copolymers. Chapters 4-6 focus on controlling block copolymer domain orientation, and Chapter 7 focuses on directed self-assembly. Chapter 8 covers spatial orientation control of domains using photopatternable interfaces. Finally, Chapter 9 covers tin-containing polymers that are resistant to fluorine-containing etch chemistries and can be used to pattern silicon oxide.

Download or read book Materials and Processes for Next Generation Lithography written by and published by Elsevier. This book was released on 2016-11-08 with total page 636 pages. Available in PDF, EPUB and Kindle. Book excerpt: As the requirements of the semiconductor industry have become more demanding in terms of resolution and speed it has been necessary to push photoresist materials far beyond the capabilities previously envisioned. Currently there is significant worldwide research effort in to so called Next Generation Lithography techniques such as EUV lithography and multibeam electron beam lithography. These developments in both the industrial and the academic lithography arenas have led to the proliferation of numerous novel approaches to resist chemistry and ingenious extensions of traditional photopolymers. Currently most texts in this area focus on either lithography with perhaps one or two chapters on resists, or on traditional resist materials with relatively little consideration of new approaches. This book therefore aims to bring together the worlds foremost resist development scientists from the various community to produce in one place a definitive description of the many approaches to lithography fabrication. Assembles up-to-date information from the world’s premier resist chemists and technique development lithographers on the properties and capabilities of the wide range of resist materials currently under investigation Includes information on processing and metrology techniques Brings together multiple approaches to litho pattern recording from academia and industry in one place

Download or read book Advanced Materials for Block Copolymer Lithography written by Christopher Martin Bates and published by . This book was released on 2013 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: The multi-billion dollar per year lithography industry relies on the fusion of chemistry, materials science, and engineering to produce technological innovations that enable continual improvements in the speed and storage density of microelectronic devices. A critical prerequisite to improving the computers of today relies on the ability to economically and controllably form thin film structures with dimensions on the order of tens of nanometers. One class of materials that potentially meets these requirements is block copolymers since they can self-assemble into structures with characteristic dimensions circa three to hundreds of nanometers. The different aspects of the block copolymer lithographic process are the subject of this dissertation. A variety of interrelated material requirements virtually necessitate the synthesis of block copolymers specifically designed for lithographic applications. Key properties for the ideal block copolymer include etch resistance to facilitate thin film processing, a large interaction parameter to enable the formation of high resolution structures, and thin film orientation control. The unifying theme for the materials synthesized herein is the presence of silicon in one block, which imparts oxygen etch resistance to just that domain. A collection of silicon-containing block copolymers was synthesized and characterized, many of which readily form features on approximately the length scale required for next-generation microelectronic devices. The most important thin film processing step biases the orientation of block copolymer domains perpendicular to the substrate by control of interfacial interactions. Both solvent and thermal annealing techniques were extensively studied to achieve orientation control. Ultimately, a dual top and bottom surface functionalization strategy was developed that utilizes a new class of "top coats" and cross-linkable substrate surface treatments. Perpendicular block copolymer features can now be produced quickly with a process amenable to existing manufacturing technology, which was previously impossible. The development of etching recipes and pattern transfer processes confirmed the through-film nature of the features and the efficacy of both the block copolymer design and the top coat process.

Download or read book Advanced Materials for Next Generation Lithography written by Evan Lawrence Schwartz and published by . This book was released on 2011 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: The constant demand for increased circuit density and higher resolution patterning calls for simultaneous advancements in materials chemistry. A variety of possible approaches for next-generation lithography are explored, centering on the use of directly patternable self-assembling block copolymers, along with hafnium oxidebased nanoparticle photoresists. In one example of the first approach, a random copolymer brush layer of poly(styrene-ran-hydroxystyrene) was designed and synthesized to precisely tune the substrate/polymer surface energy for a lithographically patternable poly([alpha]methylstyrene-block-4-hydroxystyrene) (P[alpha]MS-b-PHOST) block copolymer. The surface was designed to avoid preferential wetting of either P[alpha]MS or PHOST domains to the substrate and orient the block copolymer domains vertically relative to the substrate. To neutralize the polymer/ vapor interface during solvent vapor processing, the film was exposed to a mixed solvent vapor of a defined polarity, creating vertical microdomains with long-range order. In the latter approach, hafnium oxide nanoparticles were covalently coated with a photo-reactive ligand, which allowed neighboring nanoparticles to form a crosslinked network upon exposure to ultraviolet light. The basic science of this new class of resist material is discussed. These negative-tone resists have so far demonstrated sub-50 nm resolution using 193nm interference lithography, and plasma etch resistance over thirteen times greater than PHOST under standard silicon etching conditions. In a combination of the two approaches, the co-assembly of the inorganic nanoparticles with the PHOST phase of P[alpha]MS-b-PHOST is shown. TEM and SAXS studies indicated the expansion of the microdomain periodicity upon nanoparticle incorporation. These block copolymer nanocomposite films offer enhanced functionality and a larger process window for subsequent pattern transfer into semiconductor substrates. In another example of co-assembly, phenolic molecular glass photoresists were blended with low molecular weight, triblock copolymer surfactants based on poly(ethylene oxide)(PEO). The miscibility of these blend components is shown to be a result of preferential hydrogen bonding between the hydroxyl groups attached to the molecular glass and the alkyl ether group of the PEO block, as shown by FTIR and DSC analysis. The blending resulted in an enhancement in segregation strength that led to the formation of sub-10nm self-assembled morphologies, as verified by SAXS. Options for the lithographic patterning of these blends are explored. Lastly, a combined additive and subtractive patterning technique is demonstrated that allows the deposition of multiple block copolymer films, of different domain sizes and pitches, on the same layer of the substrate. The approach used a semifluorinated negative-tone photoresist which is designed to resist intermixing when spin coated on top of a block copolymer film.

Download or read book Design Synthesis and Engineering of Advanced Materials for Block Copolymer Lithography written by William John Durand and published by . This book was released on 2015 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt: Block copolymers (BCPs) are an attractive alternative for patterning applications used to produce next-generation microelectronic devices. Advancements require the development of high interaction parameter [chi] BCPs that enable patterning at the sub-10 nm length scale. Several organosilicon BCPs were designed to both enhance [chi] and impart an inherent etch selectivity that facilitates pattern transfer processes. Increasing the BCP silicon content both increases [chi] and bolsters the etch resistance, providing a pathway to designing new high-[chi] materials. Unfortunately, the BCPs investigated are not amenable to thermal annealing because the organosilicon block preferentially segregates to an air/vacuum interface and drives orientation parallel to the surface. A series of spin-coatable, polarity-switching top coats (as well as other strategies) were developed to provide a "neutral" top interface and promote the perpendicular orientation of BCP domains. In addition, a methodology for evaluating the neutral condition, relying on thickness quantization and the corresponding wetting behavior (i.e. island/hole topography) of lamellae. The top coat strategy was demonstrated for several BCP systems, and perpendicular structures can successfully be etched on commercial tools and be transferred into underlying substrates. The interaction parameter [chi] was evaluated using two methods to compare the performance of several BCPs: the order-disorder transition (ODT) of symmetric diblock copolymers, and the absolute scattering profile of a disordered BCP melt. Both methods, while severely limited for quantitative comparison, indicate trends towards higher [chi] with additional appended polar and organosilicon functional groups. Furthermore, the pattern fidelity is shown to be a function of the overall BCP segregation strength. The free energy of confined lamella was modeled algebraically to produce response surface plots capable of identifying process conditions favorable for perpendicular orientation. Thickness independent perpendicular orientation is only favorable using two neutral interfaces. Incommensurate film thicknesses are the most favorable, with commensurability conditions dependent on the wetting behavior at each interface. The modeling was supplemented with an extensive body of thin film experimental work that qualitatively agrees well with the above conclusions.

Download or read book Polyhydroxystyrene based Block Copolymers for Next Generation Lithography written by Jian Sun (Ph.D.) and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Studies on block copolymer (BCP) materials and their phase separation in bulk and thin-film forms have exploded over the last decades, due to the wide range of accessible morphologies (e.g. spheres, cylinders, gyroid, and lamellae) and feature sizes (5-200 nm). BCPs are advantageous in generating periodic patterns at nanoscale over a large area. Hence, BCP lithography is considered to be a promising candidate for microelectronics as sub-10 nm feature sizes can be achieved in a scalable manner. It is also considered to be more cost-effective and less tedious compared to patterning methods such as electron-beam lithography and extreme ultraviolet lithography. While accessing sub-5 nm feature size is no longer a challenge utilizing BCP self-assembly, transferring the self-assembled BCP features to a substrate with high fidelity presents enormous challenges, especially at the 10 nm length scale. The work presented in this thesis focuses on rational design, synthesis and self-assembly studies of BCPs with high interaction parameters to address the outstanding challenges in BCP lithography at very small length scales, namely aligning BCP films vertically oriented to the substrate and imparting sufficient etch contrast to achieve pattern transfer. In this thesis, a new family of BCPs is designed and synthesized by combining poly(3-hydroxystyrene) (P3HS) and poly(dimethylsiloxnae) (PDMS) as the two blocks. We develop synthetic routes to generate both diblock (P3HS-b-PDMS) and triblock (P3HS-b-PDMS-b-P3HS) architectures. This is achieved by polymerizing tetrahydropyran-protected hydroxystyrene and subsequent deprotection under mild condition, which prevents the decomposition of acid-sensitive PDMS. Self-assembly behavior in bulk and thin-film of diblocks and triblocks are studied and compared. The functionality provided by the hydroxystyrene and siloxane blocks is further exploited to demonstrate a path to pattern transfer. The major contributions of this thesis are 1) development of a synthetic route that is compatible for BCPs with acid-sensitive Si-containing block, 2) development of non-equilibrium processing protocols based on solvent annealing to align the ultrahigh interaction parameter BCPs vertically to the substrate, and 3) deciphering the effect of architecture and dispersity on the BCP self-assembly.

Download or read book Design of Silicon containing Block Copolymer Materials for Applications in Lithography written by Gregory Blachut and published by . This book was released on 2016 with total page 440 pages. Available in PDF, EPUB and Kindle. Book excerpt: Continual advancement in microelectronic performance has made microelectronics essentially ubiquitous, enriching modern life in ways unimaginable even a few decades ago. The advancement in microelectronic devices is made possible by advancements in the manufacturing processes used to make them. Chief among these technologies is lithography, the process by which the individual components on the device are patterned. At present, complex and complicated double-patterning processes are being used to extend the resolution of the lithographic methods used in high-volume manufacturing, but only at great cost. Future generations of microelectronic devices will require even further use of multiple-patterning processes, at which point the economics of manufacturing could prevent the commercialization of such devices. This economic reality has spurred interest in alternative patterning technologies. One of the leading potential methods is to exploit the self-assembly of block copolymers (BCPs). BCPs are a type of polymer consisting of two or more chemically distinct blocks that are covalently joined together. The components of a BCP can phase-separate, and the resultant features form on the 5 to 50 nm length-scale. This size range is coincidentally ideal for next-generation semiconductor devices. However, BCPs on their own do not immediately form device-relevant features. Processes known collectively as directed self-assembly (DSA) are needed to properly guide BCPs. The work in this dissertation focuses on a very specific class of BCPs, those that contain silicon in just one of the blocks. The presence of silicon in the molecule produces many lithographic advantages, but also requires specialized processing steps. Chapter 1 provides an overview of lithography and block copolymer self-assembly. Chapter 2 introduces the materials and techniques needed to control the behavior of silicon-containing BCPs. Chapter 3 presents and characterizes a variety of silicon-containing BCPs. Last, Chapters 4 and 5 describe two implementations of silicon-containing BCP DSA, one for semiconductor patterning, and the other for hard disk drive applications.

Download or read book High Interaction Parameter Block Copolymers for Advanced Lithography written by Julia Dianne Cushen and published by . This book was released on 2013 with total page 450 pages. Available in PDF, EPUB and Kindle. Book excerpt: Block copolymers demonstrate potential in next-generation lithography as a solution for overcoming the limitations of conventional lithographic techniques. Ideal block copolymer materials for this application can be synthesized on a commercial scale, have high [chi]-parameters promoting self-assembly into sub-20 nm pitch domains, have controllable alignment and orientation, and have high etch contrast between the domains for facilitating pattern transfer into the underlying substrate. Block copolymers that contain silicon in one domain are attractive for nanopatterning since they often fulfill at least three of these requirements. However, silicon-containing materials are notoriously difficult to orient in thin films due to the low surface energy of the silicon-containing block, which typically wets the free surface interface. In this work, the methodology behind material choice and the synthesis of new silicon-containing block copolymers by a variety of polymerization techniques will be described. Thin film self-assembly of the block copolymers with domains oriented perpendicular to the plane of the substrate is achieved using different solvent annealing and neutral surface treatments with thermal annealing conditions. Block copolymer patterns are transferred to the underlying substrate by reactive ion etching and directed self-assembly of the polymers is demonstrated using chemical contrast patterns. Interesting thermodynamics governing the self-assembly of block copolymers with solvent annealing will also be discussed. Finally, new amphiphilic block copolymers will be described that were created with lithographic applications in mind but that are most useful for biological applications in drug delivery.

Download or read book Submicron Porous Materials written by Paolo Bettotti and published by Springer. This book was released on 2017-02-21 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the latest research on porous materials at the submicron scale and inspires readers to better understand the porosity of materials, as well as to develop innovative new materials. A comprehensive range of materials are covered, including carbon-based and organic-based porous materials, porous anodic alumina, silica, and titania-based sol-gel materials. The fabrication, characterization, and applications of these materials are all explored, with applications ranging from sensors, thermoelectrics, catalysis, energy storage, to photovoltaics. Also of practical use for readers are chapters that describe the basics of porous silicon fabrication and its use in optical sensing and drug delivery applications; how thermal transport is affected in porous materials; how to model diffusion in porous materials; and a unique chapter on an innovative spectroscopic technique used to characterize materials' porosity. This is an ideal book for graduate students, researchers, and professionals who work with porous materials.

Download or read book Patternable Materials for Next generation Lithography written by Austin Patrick Lane and published by . This book was released on 2017 with total page 462 pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the salient truths facing the microelectronics industry today is that photolithography tools are unable to meet the resolution requirements for manufacturing next-generation devices. In the past, circuit feature sizes have been minimized by reducing the exposure wavelength used for patterning. However, this strategy failed with the worldwide dereliction of 157 nm lithography in 2003. Extreme ultraviolet (EUV) lithography still faces many technical challenges and is not ready for high volume manufacturing. How will the microelectronics industry continue to innovate without regular advances in photopatterning technology? Regardless of which paradigm is adopted, new materials will probably be required to meet the specific challenges of scaling down feature sizes and satisfying the economic ultimatum of Moore’s Law. In the search for higher resolution patterning tools, device manufacturers have identified block copolymer (BCP) lithography as a possible technique for next-generation nanofabrication. BCP self-assembly offers access to sub-5 nm features in thin films, well beyond the resolution limits of photolithography. However, BCP materials must be carefully designed, synthesized, and processed to create lithographically interesting features with good etch resistance for pattern transfer. In this dissertation, we describe a pattern transfer process for 5 nm BCP lamellae and a directed self-assembly (DSA) process for aligning 5 nm structures in thin films. To achieve defect-free alignment, the interfacial interactions between the BCP and pre-patterned substrate must be precisely controlled. We also discuss a new process for selectively modifying oxidized chromium films using polymer brushes, which could further improve the aforesaid DSA process. To facilitate better pattern transfer of BCP structures, several new BCPs with “self-developing” blocks were synthesized and tested. These materials depolymerize and evaporate in strongly acidic environments, leading to developed BCP features without the need for etching or solvent. “Self-developing” polymers may also be useful materials for traditional photolithography. Chemically amplified resists used in manufacturing today are fundamentally limited by a trade-off between sensitivity and pattern quality. To overcome this problem, we present a new type of photoresist that relies on depolymerization, rather than catalysis, to achieve amplification without producing significant roughness or bias in the final pattern

Download or read book Developments in Block Copolymer Science and Technology written by Ian W. Hamley and published by John Wiley & Sons. This book was released on 2004-03-05 with total page 388 pages. Available in PDF, EPUB and Kindle. Book excerpt: Focuses on recent advances in research on block copolymers, covering chemistry (synthesis), physics (phase behaviors, rheology, modeling), and applications (melts and solutions). Written by a team of internationally respected scientists from industry and academia, this text compiles and reviews the expanse of research that has taken place over the last five years into one accessible resource. Ian Hamley is the world-leading scientist in the field of block copolymer research Presents the recent advances in the area, covering chemistry, physics and applications. Provides a broad coverage from synthesis to fundamental physics through to applications Examines the potential of block copolymers in nanotechnology as self-assembling soft materials

Download or read book Introduction to Microlithography written by L. F. Thompson and published by Academic. This book was released on 1994 with total page 568 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reviews the theory, materials, and processes used in the lithographic process by which circuit elements are fabricated (it is these elements' decreasing size that has made possible the miniaturization of electronic devices). After a brief historical introduction, four major topics are discussed: the physics of the lithographic process, organic resist materials, resist processing, and plasma etching. The new edition reflects the many changes that have occurred since the 1983 publication of this tutorial/reference. Annotation copyright by Book News, Inc., Portland, OR

Download or read book Extending Moore s Law through Advanced Semiconductor Design and Processing Techniques written by Wynand Lambrechts and published by CRC Press. This book was released on 2018-09-13 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a methodological understanding of the theoretical and technical limitations to the longevity of Moore’s law. The book presents research on factors that have significant impact on the future of Moore’s law and those factors believed to sustain the trend of the last five decades. Research findings show that boundaries of Moore’s law primarily include physical restrictions of scaling electronic components to levels beyond that of ordinary manufacturing principles and approaching the bounds of physics. The research presented in this book provides essential background and knowledge to grasp the following principles: Traditional and modern photolithography, the primary limiting factor of Moore’s law Innovations in semiconductor manufacturing that makes current generation CMOS processing possible Multi-disciplinary technologies that could drive Moore's law forward significantly Design principles for microelectronic circuits and components that take advantage of technology miniaturization The semiconductor industry economic market trends and technical driving factors The complexity and cost associated with technology scaling have compelled researchers in the disciplines of engineering and physics to optimize previous generation nodes to improve system-on-chip performance. This is especially relevant to participate in the increased attractiveness of the Internet of Things (IoT). This book additionally provides scholarly and practical examples of principles in microelectronic circuit design and layout to mitigate technology limits of previous generation nodes. Readers are encouraged to intellectually apply the knowledge derived from this book to further research and innovation in prolonging Moore’s law and associated principles.

Download or read book Materials Design for Block Copolymer Lithography written by and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Block copolymers (BCPs) have attracted a great deal of scientific and technological interest due to their ability to spontaneously self-assemble into dense periodic nanostructures with a typical length scale of 5 to 50 nm. The use of self-assembled BCP thin-films as templates to form nanopatterns over large-area is referred to as BCP lithography. Directed self-assembly of BCPs is now viewed as a viable candidate for sub-20 nm lithography by the semiconductor industry. However, there are multiple aspects of assembly and materials design that need to be addressed in order for BCP lithography to be successful. These include substrate modification with polymer brushes or mats, tailoring of the block copolymer chemistry, understanding thin-film assembly and developing epitaxial like methods to control long range alignment. The rational design, synthesis and self-assembly of block copolymers with large interaction parameters (chi) is described in the first part of this dissertation. Two main blocks were chosen for introducing polarity into the BCP system, namely poly(4-hydroxystyrene) and poly(2-vinylpyridine). Each of these blocks are capable of ligating Lewis acids which can increase the etch contrast between the blocks allowing for facile pattern transfer to the underlying substrate. These BCPs were synthesized by living anionic polymerization and showed excellent control over molecular weight and dispersity, providing access to sub 5-nm domain sizes. Polymer brushes consist of a polymer chain with one end tethered to the surface and have wide applicability in tuning surface energy, forming responsive surfaces and increasing biocompatibility. In the second part of the dissertation, we present a universal method to grow dense polymer brushes on a wide range of substrates and combine this chemistry with BCP assembly to fabricate nanopatterned polymer brushes. This is the first demonstration of introducing additional functionality into a BCP directing layer and opens up a wide slew of applications from directed self-assembly to biomaterial engineering.

Download or read book Integrated Nanoelectronics written by Vinod Kumar Khanna and published by Springer. This book was released on 2016-09-16 with total page 471 pages. Available in PDF, EPUB and Kindle. Book excerpt: Keeping nanoelectronics in focus, this book looks at interrelated fields namely nanomagnetics, nanophotonics, nanomechanics and nanobiotechnology, that go hand-in-hand or are likely to be utilized in future in various ways for backing up or strengthening nanoelectronics. Complementary nanosciences refer to the alternative nanosciences that can be combined with nanoelectronics. The book brings students and researchers from multiple disciplines (and therefore with disparate levels of knowledge, and, more importantly, lacunae in this knowledge) together and to expose them to the essentials of integrative nanosciences. The central idea is that the five identified disciplines overlap significantly and arguably cohere into one fundamental nanotechnology discipline. The book caters to interdisciplinary readership in contrast to many of the existing nanotechnology related books that relate to a specific discipline. The book lays special emphasis on nanoelectronics since this field has advanced most rapidly amongst all the nanotechnology disciplines and with significant commercial pervasion. In view of the significant impact that nanotechnology is predicted to have on society, the topics and their interrelationship in this book are of considerable interest and immense value to students, professional engineers, and reserachers.

Download or read book Manufacturing Techniques for Microfabrication and Nanotechnology written by Marc J. Madou and published by CRC Press. This book was released on 2011-06-13 with total page 672 pages. Available in PDF, EPUB and Kindle. Book excerpt: Designed for science and engineering students, this text focuses on emerging trends in processes for fabricating MEMS and NEMS devices. The book reviews different forms of lithography, subtractive material removal processes, and additive technologies. Both top-down and bottom-up fabrication processes are exhaustively covered and the merits of the different approaches are compared. Students can use this color volume as a guide to help establish the appropriate fabrication technique for any type of micro- or nano-machine.

Download or read book Fundamentals of Microfabrication and Nanotechnology Three Volume Set written by Marc J. Madou and published by CRC Press. This book was released on 2018-12-14 with total page 1992 pages. Available in PDF, EPUB and Kindle. Book excerpt: Now in its third edition, Fundamentals of Microfabrication and Nanotechnology continues to provide the most complete MEMS coverage available. Thoroughly revised and updated the new edition of this perennial bestseller has been expanded to three volumes, reflecting the substantial growth of this field. It includes a wealth of theoretical and practical information on nanotechnology and NEMS and offers background and comprehensive information on materials, processes, and manufacturing options. The first volume offers a rigorous theoretical treatment of micro- and nanosciences, and includes sections on solid-state physics, quantum mechanics, crystallography, and fluidics. The second volume presents a very large set of manufacturing techniques for micro- and nanofabrication and covers different forms of lithography, material removal processes, and additive technologies. The third volume focuses on manufacturing techniques and applications of Bio-MEMS and Bio-NEMS. Illustrated in color throughout, this seminal work is a cogent instructional text, providing classroom and self-learners with worked-out examples and end-of-chapter problems. The author characterizes and defines major research areas and illustrates them with examples pulled from the most recent literature and from his own work.