Download or read book Modeling and Control of Pre chamber Initiated Turbulent Jet Ignition Combustion Systems written by Ruitao Song and published by . This book was released on 2018 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experiments and Modeling of a Turbulent Jet Ignition System for Internal Combustion Engines written by Masumeh Gholamisheeri and published by . This book was released on 2017 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Review of Pre Chamber Initiated Jet Ignition Combustion Systems written by Elisa Toulson and published by . This book was released on 2010 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Injection Technologies and Mixture Formation Strategies For Spark Ignition and Dual Fuel Engines written by Alessandro Ferrari and published by SAE International. This book was released on 2022-06-24 with total page 407 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fuel injection systems and performance is fundamental to combustion engine performance in terms of power, noise, efficiency, and exhaust emissions. There is a move toward electric vehicles (EVs) to reduce carbon emissions, but this is unlikely to be a rapid transition, in part due to EV batteries: their size, cost, longevity, and charging capabilities as well as the scarcity of materials to produce them. Until these isssues are resolved, refining the spark-ignited engine is necessary address both sustainability and demand for affordable and reliable mobility. Even under policies oriented to smart sustainable mobility, spark-ignited engines remain strategic, because they can be applied to hybridized EVs or can be fueled with gasoline blended with bioethanol or bio-butanol to drastically reduce particulate matter emissions of direct injection engines in addition to lower CO2 emissions. In this book, Alessandro Ferrari and Pietro Pizzo provide a full review of spark-ignited engine fuel injection systems. The most popular typologies of fuel injection systems are considered, with special focus on state-of-the-art solutions. Dedicated sections on the methods for air mass evaluation, fuel delivery low-pressure modules, and the specific subsystems for idle, cold start, and warm-up control are also included. The authors pay special attention to mixture formation strategies, as they are a fundamental theme for SI engines. An exhaustive overview of fuel injection technologies is provided, and mixture formation strategies for spark ignited combustion engines are considered. Fuel Injection Systems illustrates the performance of these systems and will also serve as a reference for engineers who are active in the aftermarket, offering detailed information on fuel injection system solutions that are mounted in older vehicles.
Download or read book Modeling and Simulation of Turbulent Mixing and Reaction written by Daniel Livescu and published by Springer Nature. This book was released on 2020-02-19 with total page 273 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book highlights recent research advances in the area of turbulent flows from both industry and academia for applications in the area of Aerospace and Mechanical engineering. Contributions include modeling, simulations and experiments meant for researchers, professionals and students in the area.
Download or read book A Turbulent Jet Ignition Pre Chamber Combustion System for Large Fuel Economy Improvements in a Modern Vehicle Powertrain written by William P. Attard and published by . This book was released on 2010 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Modeling and Simulation of Turbulent Combustion written by Santanu De and published by Springer. This book was released on 2017-12-12 with total page 663 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a comprehensive review of state-of-the-art models for turbulent combustion, with special emphasis on the theory, development and applications of combustion models in practical combustion systems. It simplifies the complex multi-scale and nonlinear interaction between chemistry and turbulence to allow a broader audience to understand the modeling and numerical simulations of turbulent combustion, which remains at the forefront of research due to its industrial relevance. Further, the book provides a holistic view by covering a diverse range of basic and advanced topics—from the fundamentals of turbulence–chemistry interactions, role of high-performance computing in combustion simulations, and optimization and reduction techniques for chemical kinetics, to state-of-the-art modeling strategies for turbulent premixed and nonpremixed combustion and their applications in engineering contexts.
Download or read book Turbulent Combustion written by Norbert Peters and published by Cambridge University Press. This book was released on 2000-08-15 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: The combustion of fossil fuels remains a key technology for the foreseeable future. It is therefore important that we understand the mechanisms of combustion and, in particular, the role of turbulence within this process. Combustion always takes place within a turbulent flow field for two reasons: turbulence increases the mixing process and enhances combustion, but at the same time combustion releases heat which generates flow instability through buoyancy, thus enhancing the transition to turbulence. The four chapters of this book present a thorough introduction to the field of turbulent combustion. After an overview of modeling approaches, the three remaining chapters consider the three distinct cases of premixed, non-premixed, and partially premixed combustion, respectively. This book will be of value to researchers and students of engineering and applied mathematics by demonstrating the current theories of turbulent combustion within a unified presentation of the field.
Download or read book Internal Combustion Engines and Powertrain Systems for Future Transport 2019 written by IMECHE and published by CRC Press. This book was released on 2020-03-09 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt: With the changing landscape of the transport sector, there are also alternative powertrain systems on offer that can run independently of or in conjunction with the internal combustion (IC) engine. This shift has actually helped the industry gain traction with the IC Engine market projected to grow at 4.67% CAGR during the forecast period 2019-2025. It continues to meet both requirements and challenges through continual technology advancement and innovation from the latest research. With this in mind, the contributions in Internal Combustion Engines and Powertrain Systems for Future Transport 2019 not only cover the particular issues for the IC engine market but also reflect the impact of alternative powertrains on the propulsion industry. The main topics include: • Engines for hybrid powertrains and electrification • IC engines • Fuel cells • E-machines • Air-path and other technologies achieving performance and fuel economy benefits • Advances and improvements in combustion and ignition systems • Emissions regulation and their control by engine and after-treatment • Developments in real-world driving cycles • Advanced boosting systems • Connected powertrains (AI) • Electrification opportunities • Energy conversion and recovery systems • Modified or novel engine cycles • IC engines for heavy duty and off highway Internal Combustion Engines and Powertrain Systems for Future Transport 2019 provides a forum for IC engine, fuels and powertrain experts, and looks closely at developments in powertrain technology required to meet the demands of the low carbon economy and global competition in all sectors of the transportation, off-highway and stationary power industries.
Download or read book Physics of Turbulent Jet Ignition written by Sayan Biswas and published by Springer. This book was released on 2018-05-03 with total page 230 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on developing strategies for ultra-lean combustion of natural gas and hydrogen, and contributes to the research on extending the lean flammability limit of hydrogen and air using a hot supersonic jet. The author addresses experimental methods, data analysis techniques, and results throughout each chapter and: Explains the fundamental mechanisms behind turbulent hot jet ignition using non-dimensional analysis Explores ignition characteristics by impinging hot jet and multiple jets in relation to better controllability and lean combustion Explores how different instability modes interact with the acoustic modes of the combustion chamber. This book provides a potential answer to some of the issues that arise from lean engine operation, such as poor ignition, engine misfire, cycle-to-cycle variability, combustion instability, reduction in efficiency, and an increase in unburned hydrocarbon emissions. This thesis was submitted to and approved by Purdue University.
Download or read book Engine Modeling and Simulation written by Avinash Kumar Agarwal and published by Springer Nature. This book was released on 2021-12-16 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the simulation and modeling of internal combustion engines. The contents include various aspects of diesel and gasoline engine modeling and simulation such as spray, combustion, ignition, in-cylinder phenomena, emissions, exhaust heat recovery. It also explored engine models and analysis of cylinder bore piston stresses and temperature effects. This book includes recent literature and focuses on current modeling and simulation trends for internal combustion engines. Readers will gain knowledge about engine process simulation and modeling, helpful for the development of efficient and emission-free engines. A few chapters highlight the review of state-of-the-art models for spray, combustion, and emissions, focusing on the theory, models, and their applications from an engine point of view. This volume would be of interest to professionals, post-graduate students involved in alternative fuels, IC engines, engine modeling and simulation, and environmental research.
Download or read book Turbulent Combustion Modeling written by Tarek Echekki and published by Springer Science & Business Media. This book was released on 2010-12-25 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt: Turbulent combustion sits at the interface of two important nonlinear, multiscale phenomena: chemistry and turbulence. Its study is extremely timely in view of the need to develop new combustion technologies in order to address challenges associated with climate change, energy source uncertainty, and air pollution. Despite the fact that modeling of turbulent combustion is a subject that has been researched for a number of years, its complexity implies that key issues are still eluding, and a theoretical description that is accurate enough to make turbulent combustion models rigorous and quantitative for industrial use is still lacking. In this book, prominent experts review most of the available approaches in modeling turbulent combustion, with particular focus on the exploding increase in computational resources that has allowed the simulation of increasingly detailed phenomena. The relevant algorithms are presented, the theoretical methods are explained, and various application examples are given. The book is intended for a relatively broad audience, including seasoned researchers and graduate students in engineering, applied mathematics and computational science, engine designers and computational fluid dynamics (CFD) practitioners, scientists at funding agencies, and anyone wishing to understand the state-of-the-art and the future directions of this scientifically challenging and practically important field.
Download or read book Powertrain Systems for Net Zero Transport written by Institution of Mechanical Engineers (IMe and published by CRC Press. This book was released on 2021-12-21 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt: The transport sector continues to shift towards alternative powertrains, particularly with the UK Government’s announcement to end the sale of petrol and diesel passenger cars by 2030 and increasing support for alternatives. Despite this announcement, the internal combustion continues to play a significant role both in the passenger car market through the use of hybrids and sustainable low carbon fuels, as well as a key role in other sectors such as heavy-duty vehicles and off-highway applications across the globe. Building on the industry-leading IC Engines conference, the 2021 Powertrain Systems for Net-Zero Transport conference (7-8 December 2021, London, UK) focussed on the internal combustion engine’s role in Net-Zero transport as well as covered developments in the wide range of propulsion systems available (electric, fuel cell, sustainable fuels etc) and their associated powertrains. To achieve the net-zero transport across the globe, the life-cycle analysis of future powertrain and energy was also discussed. Powertrain Systems for Net-Zero Transport provided a forum for engine, fuels, e-machine, fuel cell and powertrain experts to look closely at developments in powertrain technology required, to meet the demands of the net-zero future and global competition in all sectors of the road transportation, off-highway and stationary power industries.
Download or read book Experiments and Model Development of a Dual Mode Turbulent Jet Ignition Engine written by Sedigheh Tolou and published by . This book was released on 2019 with total page 174 pages. Available in PDF, EPUB and Kindle. Book excerpt: The number of vehicles powered by a source of energy other than traditional petroleum fuels will increase as time passes. However, based on current predictions, vehicles run on liquid fuels will be the major source of transportation for decades to come. Advanced combustion technologies can improve fuel economy of internal combustion (IC) engines and reduce exhaust emissions. The Dual Mode, Turbulent Jet Ignition (DM-TJI) system is an advanced, distributed combustion technology which can achieve high diesel-like thermal efficiencies at medium to high loads and potentially exceed diesel efficiencies at low-load operating conditions. The DM-TJI strategy extends the mixture flammability limits by igniting lean and/or highly dilute mixtures, leading to low-temperature combustion (LTC) modes in spark ignition (SI) engines. A novel, reduced order, and physics-based model was developed to predict the behavior of a DM-TJI engine with a pre-chamber air valve assembly. The engine model developed was calibrated based on experimental data from a Prototype II DM-TJI engine. This engine was designed, built, and tested at the MSU Energy and Automotive Research Laboratory (EARL). A predictive, generalized model was introduced to obtain a complete engine fuel map for the DM-TJI engine. The engine fuel map was generated in a four-cylinder boosted configuration under highly dilute conditions, up to 40% external exhaust gas recirculation (EGR). A vehicle simulation was then performed to further explore fuel economy gains using the fuel map generated for the DM-TJI engine. The DM-TJI engine was embodied in an industry-based vehicle to examine the behavior of the engine over the U.S. Environmental Protection Agency (EPA) driving schedules. The results obtained from the drive cycle analysis of the DM-TJI engine in an industry-based vehicle were compared to the results of the same vehicle with its original engine. The vehicle equipped with the DM-TJI system was observed to benefit from ~13% improvement in fuel economy and ~11% reduction in CO2 emission over the EPA combined city/high driving schedules. Potential improvements were discussed, as these results of the drive cycle analysis are the first-ever reported results for a DM-TJI engine embodied in an industry-based vehicle. The resulting fuel economy and CO2 emission were used to conduct a cost-benefit analysis of a DM-TJI engine. The cost-benefit analysis followed the economic and key inputs used by the U.S. EPA in a Proposed Determination prepared by that agency. The outcomes of the cost-benefit analysis for the vehicle equipped with the DM-TJI system were reported in comparison with the same vehicle with its base engine. The extra costs of a DM-TJI engine were observed to be compensated over the first three years of the vehicle's life time. The results projected maximum savings of approximately 2400 in 2019 dollars. This includes the lifetime-discounted present value of the net benefits of the DM-TJI technology, compared to the base engine examined. In this dollar saving estimate, the societal effects of CO2 emission were calculated based on values by the interagency working group (IWG) at 3% discount rate.
Download or read book Ignition by Hot Gas Jets written by Rajesh Sadanandan and published by . This book was released on 2007 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experiments and Numerical Simulations of Diluted Spray Turbulent Combustion written by Bart Merci and published by Springer Science & Business Media. This book was released on 2011-06-20 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reflects the outcome of the 1st International Workshop on Turbulent Spray Combustion held in 2009 in Corsica (France). The focus is on reporting the progress of experimental and numerical techniques in two-phase flows, with emphasis on spray combustion. The motivation for studies in this area is that knowledge of the dominant phenomena and their interactions in such flow systems is essential for the development of predictive models and their use in combustor and gas turbine design. This necessitates the development of accurate experimental methods and numerical modelling techniques. The workshop aimed at providing an opportunity for experts and young researchers to present the state-of-the-art, discuss new developments or techniques and exchange ideas in the areas of experimentations, modelling and simulation of reactive multiphase flows. The first two papers reflect the contents of the invited lectures, given by experts in the field of turbulent spray combustion. The first concerns computational issues, while the second deals with experiments. These lectures initiated very interesting and interactive discussions among the researchers, further pursued in contributed poster presentations. Contributions 3 and 4 focus on some aspects of the impact of the interaction between fuel evaporation and combustion on spray combustion in the context of gas turbines, while the final article deals with the interaction between evaporation and turbulence.
Download or read book Modelling Diesel Combustion written by P. A. Lakshminarayanan and published by Springer Science & Business Media. This book was released on 2010-03-03 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Phenomenology of Diesel Combustion and Modeling Diesel is the most efficient combustion engine today and it plays an important role in transport of goods and passengers on land and on high seas. The emissions must be controlled as stipulated by the society without sacrificing the legendary fuel economy of the diesel engines. These important drivers caused innovations in diesel engineering like re-entrant combustion chambers in the piston, lower swirl support and high pressure injection, in turn reducing the ignition delay and hence the nitric oxides. The limits on emissions are being continually reduced. The- fore, the required accuracy of the models to predict the emissions and efficiency of the engines is high. The phenomenological combustion models based on physical and chemical description of the processes in the engine are practical to describe diesel engine combustion and to carry out parametric studies. This is because the injection process, which can be relatively well predicted, has the dominant effect on mixture formation and subsequent course of combustion. The need for improving these models by incorporating new developments in engine designs is explained in Chapter 2. With “model based control programs” used in the Electronic Control Units of the engines, phenomenological models are assuming more importance now because the detailed CFD based models are too slow to be handled by the Electronic Control Units. Experimental work is necessary to develop the basic understanding of the pr- esses.
