Download or read book Mitigation of Vortex Induced Vibrations Using Macro Fiber Composites written by Gustavo Jose Munoz and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: ABSTRACT: Vortex-Induced Vibration (VIV) in cables is a prevalent phenomenon affecting the structural health of bridges and their components. Past studies have shown both passive and active methods are beneficial in the reduction of vibrations, however, a number of issues such as excessive base moment, transformation of geometry, intrusive implementation and fatigue limit the effectiveness of current engineering. A method involving no intrusion, no geometrical manipulation and a mechanism to prevent and mitigate VIV is needed. A "skin" of material embedded with Macro-Fiber Composite (MFC) material and with the capabilities of perturbing the surface near the separation point of vortex shedding is explored and tested. Simplifications of the proposed material are made in order to understand the effects of the capabilities of a perturbing skin of MFC material. Construction of a 17-ft Open-circuit wind tunnel is done in order to make the VIV condition to be tested with the near method of VIV control. The VIV on cables is recorded. Experiments are run inside the tunnel at a Re of 11400 and 6400. In order to see the effects of surface perturbations, an MFC actuation mechanism is made and a cable section effectively able to cause surface perturbations is built. A test is then run to find the effect of different angles of perturbation. Finally, a testing and analysis of a phase-difference of a signal, at prescribed perturbation frequencies is done. This is analyzed against surface vortex formation theory. The data are analyzed in order to see the capabilities of an MFC skin on VIV of cables. The mechanism shows promise in both reducing VIV and providing for a low-key, non-intrusive control mechanism.
Download or read book Piezoelectric Energy Harvesting written by Alper Erturk and published by John Wiley & Sons. This book was released on 2011-04-04 with total page 377 pages. Available in PDF, EPUB and Kindle. Book excerpt: The transformation of vibrations into electric energy through the use of piezoelectric devices is an exciting and rapidly developing area of research with a widening range of applications constantly materialising. With Piezoelectric Energy Harvesting, world-leading researchers provide a timely and comprehensive coverage of the electromechanical modelling and applications of piezoelectric energy harvesters. They present principal modelling approaches, synthesizing fundamental material related to mechanical, aerospace, civil, electrical and materials engineering disciplines for vibration-based energy harvesting using piezoelectric transduction. Piezoelectric Energy Harvesting provides the first comprehensive treatment of distributed-parameter electromechanical modelling for piezoelectric energy harvesting with extensive case studies including experimental validations, and is the first book to address modelling of various forms of excitation in piezoelectric energy harvesting, ranging from airflow excitation to moving loads, thus ensuring its relevance to engineers in fields as disparate as aerospace engineering and civil engineering. Coverage includes: Analytical and approximate analytical distributed-parameter electromechanical models with illustrative theoretical case studies as well as extensive experimental validations Several problems of piezoelectric energy harvesting ranging from simple harmonic excitation to random vibrations Details of introducing and modelling piezoelectric coupling for various problems Modelling and exploiting nonlinear dynamics for performance enhancement, supported with experimental verifications Applications ranging from moving load excitation of slender bridges to airflow excitation of aeroelastic sections A review of standard nonlinear energy harvesting circuits with modelling aspects.
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1992 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental Vibration Analysis for Civil Structures written by Joel P. Conte and published by Springer. This book was released on 2017-10-11 with total page 926 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edited volume presents selected contributions from the International Conference on Experimental Vibration Analysis of Civil Engineering Structures held in San Diego, California in 2017 (EVACES2017). The event brought together engineers, scientists, researchers, and practitioners, providing a forum for discussing and disseminating the latest developments and achievements in all major aspects of dynamic testing for civil engineering structures, including instrumentation, sources of excitation, data analysis, system identification, monitoring and condition assessment, in-situ and laboratory experiments, codes and standards, and vibration mitigation.
Download or read book Flow Induced Vibrations written by Eduard Naudascher and published by Courier Corporation. This book was released on 2012-03-27 with total page 434 pages. Available in PDF, EPUB and Kindle. Book excerpt: Despite their variety, the vibration phenomena from many different engineering fields can be classified into a relatively few basic excitation mechanisms. The classification enables engineers to identify all possible sources of excitation in a given system and to assess potential dangers. This graduate-level text presents a synthesis of research results and practical experience from disparate fields in the form of engineering guidelines. It is particularly geared toward assessing the possible sources of excitation in a flow system, in identifying the actual danger spots, and in finding appropriate remedial measures or cures. Flow-induced vibrations are presented in terms of their basic elements: body oscillators, fluid oscillators, and sources of excitation. By stressing these basic elements, the authors provide a basis for the transfer of knowledge from one system to another, as well as from one engineering field to another. In this manner, well-known theories on cylinders in cross-flow or well-executed solutions from the field of wind engineering--to name just two examples--may be useful in other systems or fields on which information is scarce. The unified approach is broad enough to permit treatment of the major excitation mechanism, yet simple enough to be of practical use.
Download or read book Thin Walled Composite Beams written by Liviu Librescu and published by Springer Science & Business Media. This book was released on 2006-01-15 with total page 627 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation This is the first monograph devoted to the foundation of the theory of composite anisotropic thin-walled beams and to its applications in various problems involving the aeronautical/aerospace, helicopter, naval and mechanical structures. Throughout the theoretical part, an effort was made to provide the treatment of the subject by using the equations of the 3-D elasticity theory. Non-classical effects such as transverse shear, warping constraint, anisotropy of constituent materials yielding the coupling of twist-bending (lateral), bending (transversal)-extension have been included and their implications have been thoroughly analyzed. Thermal effects have been included and in order to be able to circumvent their deleterious effects, functionally graded materials have been considered in their construction. Implications of the application of the tailoring technique and of the active feedback control on free vibration, dynamic response, instability and aeroelasticity of such structures have been amply investigated. Special care was exercised throughout this work to address and validate the adopted solution methodologies and the obtained results against those available in the literature and obtained via numerical or experimental means.
Download or read book Energy Harvesting from Flow Induced Vibration written by DANIIL. WANG YURCHENKO (JUNLEI. ABDELKEFI, ABDESSATTAR.) and published by VCH. This book was released on 2022-07-13 with total page 300 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Piezoelectric Transducers for Vibration Control and Damping written by S.O. Reza Moheimani and published by Springer Science & Business Media. This book was released on 2006-06-29 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents recent developments in vibration control systems that employ embedded piezoelectric sensors and actuators, reviewing ways in which active vibration control systems can be designed for piezoelectric laminated structures, paying distinct attention to how such control systems can be implemented in real time. Includes numerous examples and experimental results obtained from laboratory-scale apparatus, with details of how similar setups can be built.
Download or read book International Aerospace Abstracts written by and published by . This book was released on 1997 with total page 940 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Introduction to Permanent Plug and Abandonment of Wells written by Mahmoud Khalifeh and published by Springer Nature. This book was released on 2020-01-27 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book offers a timely guide to challenges and current practices to permanently plug and abandon hydrocarbon wells. With a focus on offshore North Sea, it analyzes the process of plug and abandonment of hydrocarbon wells through the establishment of permanent well barriers. It provides the reader with extensive knowledge on the type of barriers, their functioning and verification. It then discusses plug and abandonment methodologies, analyzing different types of permanent plugging materials. Last, it describes some tests for verifying the integrity and functionality of installed permanent barriers. The book offers a comprehensive reference guide to well plugging and abandonment (P&A) and well integrity testing. The book also presents new technologies that have been proposed to be used in plugging and abandoning of wells, which might be game-changing technologies, but they are still in laboratory or testing level. Given its scope, it addresses students and researchers in both academia and industry. It also provides information for engineers who work in petroleum industry and should be familiarized with P&A of hydrocarbon wells to reduce the time of P&A by considering it during well planning and construction.
Download or read book Materials Design and Manufacturing for Sustainable Environment written by Santhakumar Mohan and published by Springer Nature. This book was released on 2021-02-06 with total page 909 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises the select proceedings of the International Conference on Materials, Design and Manufacturing for Sustainable Environment (ICMDMSE 2020). The primary focus is on emerging materials and cutting-edge manufacturing technologies for sustainable environment. The book covers a wide range of topics such as advanced materials, vibration, tribology, finite element method (FEM), heat transfer, fluid mechanics, energy engineering, additive manufacturing, robotics and automation, automobile engineering, industry 4.0, MEMS and nanotechnology, optimization techniques, condition monitoring, and new paradigms in technology management. Contents of this book will be useful to students, researchers, and practitioners alike.
Download or read book Fluid Structure Interaction written by Hans-Joachim Bungartz and published by Springer Science & Business Media. This book was released on 2007-06-24 with total page 401 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume in the series Lecture Notes in Computational Science and Engineering presents a collection of papers presented at the International Workshop on FSI, held in October 2005 in Hohenwart and organized by DFG's Research Unit 493 "FSI: Modeling, Simulation, and Optimization". The papers address partitioned and monolithic coupling approaches, methodical issues and applications, and discuss FSI from the mathematical, informatics, and engineering points of view.
Download or read book Smart Structures written by Jan Holnicki-Szulc and published by Springer Science & Business Media. This book was released on 1999-02-28 with total page 408 pages. Available in PDF, EPUB and Kindle. Book excerpt: Smart (intelligent) structures have been the focus of a great deal of recent research interest. In this book, leading researchers report the state of the art and discuss new ideas, results and trends in 43 contributions, covering fundamental research issues, the role of intelligent monitoring in structural identification and damage assessment, the potential of automatic control systems in achieving a desired structural behaviour, and a number of practical issues in the analysis and design of smart structures in mechanical and civil engineering applications. Audience: A multidisciplinary reference for materials scientists and engineers in such areas as mechanical, civil, aeronautical, electrical, control, and computer engineering.
Download or read book Viscoelastic Materials written by Roderic S. Lakes and published by Cambridge University Press. This book was released on 2009-04-27 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: This graduate text on viscoelastic materials addresses design applications as diverse as earplugs, computer disks and medical diagnostics.
Download or read book IUTAM Symposium on Nonlinear Dynamics for Advanced Technologies and Engineering Design written by Marian Wiercigroch and published by Springer Science & Business Media. This book was released on 2013-01-11 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nonlinear dynamics has been enjoying a vast development for nearly four decades resulting in a range of well established theory, with the potential to significantly enhance performance, effectiveness, reliability and safety of physical systems as well as offering novel technologies and designs. By critically appraising the state of the art, it is now time to develop design criteria and technology for new generation products/processes operating on principles of nonlinear interaction and in the nonlinear regime, leading to more effective, sensitive, accurate, and durable methods than what is currently available. This new approach is expected to radically influence the design, control and exploitation paradigms, in a magnitude of contexts. With a strong emphasis on experimentally calibrated and validated models, contributions by top-level international experts will foster future directions for the development of engineering technologies and design using robust nonlinear dynamics modelling and analysis.
Download or read book Geo frontiers 2011 written by and published by . This book was released on 2011 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Computational Mesomechanics of Composites written by Leon L. Mishnaevsky, Jr and published by John Wiley & Sons. This book was released on 2007-08-20 with total page 294 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mechanical properties of composite materials can be improved by tailoring their microstructures. Optimal microstructures of composites, which ensure desired properties of composite materials, can be determined in computational experiments. The subject of this book is the computational analysis of interrelations between mechanical properties (e.g., strength, damage resistance stiffness) and microstructures of composites. The methods of mesomechanics of composites are reviewed, and applied to the modelling of the mechanical behaviour of different groups of composites. Individual chapters are devoted to the computational analysis of the microstructure- mechanical properties relationships of particle reinforced composites, functionally graded and particle clusters reinforced composites, interpenetrating phase and unidirectional fiber reinforced composites, and machining tools materials.
