Download or read book Microstructural Evolution of AA6061 Subjected to Severe Plastic Deformation written by Yogesh Bhambri and published by . This book was released on 2003 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Microstructural Evolution in the 2219 Aluminum Alloy During Severe Plastic Deformation written by and published by . This book was released on 2000 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Numerous investigations have demonstrated that intense plastic deformation is an attractive procedure for producing an ultrafine grain size in metallic materials. Torsional deformation under high pressure and equal-channel angular extrusion are two techniques that can produce microstructures with grain sizes in the submicrometer and nanometer range. Materials with these microstructures have many attractive properties. The microstructures formed by these two processing techniques are essentially the same and thus the processes occurring during deformation should be the same. Most previous studies have examined the final microstructures produced as a result of severe plastic deformation and the resulting properties. Only a limited number of studies have examined the evolution of microstructure. As a result, some important aspects of ultra-fine grain formation during severe plastic deformation remain unknown. There is also limited data on the influence of the initial state of the material on the microstructural evolution and mechanisms of ultra-fine grain formation. This limited knowledge base makes optimization of processing routes difficult and retards commercial application of these techniques. The objective of the present work is to examine the microstructure evolution during severe plastic deformation of a 2219 aluminum alloy. Specific attention is given to the mechanism of ultrafine grain formation as a result of severe plastic deformation.

Download or read book High Performance Metallic Composites Fabricated by Advanced Rolling Techniques written by Hailiang Yu and published by Springer Nature. This book was released on with total page 294 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Process dependent Microstructure and Severe Plastic Deformation in SiCp Reinforced Aluminum Metal Matrix Composites written by Catalina Uribe-Restrepo and published by . This book was released on 2011 with total page 88 pages. Available in PDF, EPUB and Kindle. Book excerpt: Discontinuously reinforced MMCs with optimized microstructure are sought after for exceptional high strain rate behavior. The microstructure evolution of a stir-cast A359 aluminum composite reinforced with 30 vol.% SiC[subscript p] after isothermal anneal, successive hot-rolling, and high strain rate deformation has been investigated. Quantitative microstructural analysis was carried out for the as-cast, annealed (470°C, 538°C and 570°C) and successively hot rolled specimens (64, 75, 88, and 96% rolling reductions). Selected composites were also examined after high strain rate deformation. X-ray diffraction, optical microscopy, scanning electron microscopy and transmission electron microscopy were employed for microstructural characterization. The strength and ductility of the A359 Al alloys, and the composite, were greatly influenced by the brittle eutectic silicon phase and its morphology. Lamellar eutectic silicon spheroidized with isothermal anneal and successive hot rolling with a corresponding decrease in hardness. The hot rolling process also considerably decreased the SiC particle size (approximately 20% after 96% reduction) by breaking-up the hard SiC particles. However, this break-up of particles increased the homogeneity of SiC[subscript p] size distribution. Successive hot rolling also healed voids due to solidification shrinkage, incomplete infiltration of molten Al and defects originating from fractured particles. Four selected specimens of composites were examined after high strain rate deformation. Fractography and metallographic analysis for the craters, voids, and relevant regions affected by the high velocity impact were carried out. The deposition of impact residuals was frequently observed on the exposed fracture surfaces. These residuals were typically observed as "molten-and-solidified" as a consequence of excessive heat generated during and after the damage. Particularly in regions of entry and exit of impact, intermixing of residuals and composite constituents were observed, demonstrating that the Al matrix of the composite also had melted. In all samples examined, cracks were observed to propagate through the eutectic Si network while a small number of broken reinforcement particles were observed. A slight variation in failure mechanisms was observed (e.g., radial, fragmentation, petalling) corresponding to the variation in ductility against high strain rate deformation. In selected specimens, parallel sub-cracks at the exit were observed at 45° and 30°. These sub-cracks were again filled with intermixed constituents from projectile residuals and composites. This observation suggests that the melting of composite constituents that leads to intermixing occured after the crack propagation and other damage.

Download or read book Thermo Mechanical Processing of Metallic Materials written by Bert Verlinden and published by Elsevier. This book was released on 2007-06-07 with total page 551 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermo-Mechanical Processing of Metallic Materials describes the science and technology behind modern thermo-mechanical processing (TMP), including detailed descriptions of successful examples of its application in the industry. This graduate-level introductory resource aims to fill the gap between two scientific approaches and illustrate their successful linkage by the use of suitable modern case studies. The book is divided into three key sections focusing on the basics of metallic materials processing. The first section covers the microstructural science base of the subject, including the microstructure determined mechanical properties of metals. The second section deals with the current mechanical technology of plastic forming of metals. The concluding section demonstrates the interaction of the first two disciplines in a series of case studies of successful current TMP processing and looks ahead to possible new developments in the field. This text is designed for use by graduate students coming into the field, for a graduate course textbook, and for Materials and Mechanical Engineers working in this area in the industry. * Covers both physical metallurgy and metals processing* Links basic science to real everyday applications* Written by four internationally-known experts in the field

Download or read book Microstructural Development and Thermal Stability of Aluminium based Composites Processed by Severe Plastic Deformation written by Hamidreza Mohseni and published by . This book was released on 2006 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Microstructural Control of a Precipitate Hardenable Al Ag Alloy Using Severe Plastic Deformation written by Kunihiro Ohashi and published by . This book was released on 2004 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: An Al-10.8wt%Ag alloy was subjected to aging treatment followed by Equal-Channel Angular Pressing (ECAP) (designated process AE) or ECAP followed by aging treatment (designated process EA). Hardness measurements were undertaken with respect to the number of ECAP passes for process AE or with respect to aging time for process EA. Microstructures were examined by transmission electron microscopy (TEM) including X-ray mapping. It is shown that age hardening is observed for the ECAP sample due to the precipitation of very fine particles within the small grains.

Download or read book Nanomaterials by Severe Plastic Deformation IV written by Yuri Estrin and published by . This book was released on 2008 with total page 640 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprises 175 articles on 'Nanomaterials by Severe Plastic Deformation'. This title demonstrates the relevance of bulk ultrafine grained and nanostructured materials, produced by severe plastic deformation, to a wide range of researchers and engineers.

Download or read book Materials Under Extreme Conditions written by A. K. Tyagi and published by Elsevier. This book was released on 2017-01-13 with total page 872 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials Under Extreme Conditions: Recent Trends and Future Prospects analyzes the chemical transformation and decomposition of materials exposed to extreme conditions, such as high temperature, high pressure, hostile chemical environments, high radiation fields, high vacuum, high magnetic and electric fields, wear and abrasion related to chemical bonding, special crystallographic features, and microstructures. The materials covered in this work encompass oxides, non-oxides, alloys and intermetallics, glasses, and carbon-based materials. The book is written for researchers in academia and industry, and technologists in chemical engineering, materials chemistry, chemistry, and condensed matter physics. - Describes and analyzes the chemical transformation and decomposition of a wide range of materials exposed to extreme conditions - Brings together information currently scattered across the Internet or incoherently dispersed amongst journals and proceedings - Presents chapters on phenomena, materials synthesis, and processing, characterization and properties, and applications - Written by established researchers in the field

Download or read book Simulating Microstructure Evolution of Realistic 3D Aluminum Alloy Polycrystal During Large Plastic Deformation at Elevated Temperature written by Jing Lu and published by . This book was released on 2006 with total page 230 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Analysis of Microstructure Evolution in Hot Worked Aluminium Subjected to Non linear Deformation written by Magdalena López-Pedrosa and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book The Microstructural Evolution of Aluminum During the Course of High Temperature Creep written by Richard Grant Connell and published by . This book was released on 1973 with total page 1058 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Flow Behavior and Microstructural Evolution During Superplastic Deformation of AA8090 Aluminum lithium Alloy written by Wenjie Fan and published by . This book was released on 1998 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Metals Abstracts written by and published by . This book was released on 1998 with total page 1076 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Additive Friction Stir Deposition written by Hang Z. Yu and published by Elsevier. This book was released on 2022-07-19 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Additive Friction Stir Deposition is a comprehensive summary of the state-of-the-art understanding on this emerging solid-state additive manufacturing technology. Sections cover additive friction stir deposition, encompassing advances in processing science, metallurgical science and innovative applications. The book presents a clear description of underlying physical phenomena, shows how the process determines the printing quality, covers resultant microstructure and properties in the as-printed state, highlights its key capabilities and limitations, and explores niche applications in repair, cladding and multi-material 3D printing. Serving as an educational and research guide, this book aims to provide a holistic picture of additive friction stir deposition-based solid-state additive manufacturing as well as a thorough comparison to conventional beam-based metal additive manufacturing, such as powder bed fusion and directed energy deposition. - Provides a clear process description of additive friction stir deposition and highlights key capabilities - Summarizes the current research and application of additive friction stir deposition, including material flow, microstructure evolution, repair and dissimilar material cladding - Discusses future applications and areas of research for this technology

Download or read book Bulk Nanostructured Materials written by Ruslan Z. Valiev and published by John Wiley & Sons. This book was released on 2013-09-17 with total page 468 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the most recent results in the area of bulk nanostructured materials and new trends in their severe plastic deformation (SPD) processing, where these techniques are now emerging from the domain of laboratory-scale research into the commercial production of various bulk nanomaterials. Special emphasis is placed on an analysis of the effect of nanostructures in materials fabricated by SPD on mechanical properties (strength and ductility, fatigue strength and life, superplasticity) and functional behavior (shape memory effects, magnetic and electric properties), as well as the numerous examples of their innovative applications. There is a high innovation potential for industrial applications of bulk nanomaterials for structural use (materials with extreme strength) as well as for functional applications such as nanomagnets, materials for hydrogen storage, thermoelectric materials, superconductors, catalysts, and biomedical implants.

Download or read book Handbook of Aluminum written by George E. Totten and published by CRC Press. This book was released on 2003-03-27 with total page 1318 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Handbook of Aluminum: Vol. 1: Physical Metallurgy and Processes covers all aspects of the physical metallurgy, analytical techniques, and processing of aluminium, including hardening, annealing, aging, property prediction, corrosion, residual stress and distortion, welding, casting, forging, molten metal processing, machining, rolling, and extrusion. It also features an extensive, chapter-length consideration of quenching.