Download or read book Materials Selection for Process Plants written by Russell E. Gackenbach and published by . This book was released on 1960 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Materials Selection for Hydrocarbon and Chemical Plants written by David A. Hansen and published by Routledge. This book was released on 2017-11-22 with total page 425 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describes the systematic procedure for using process and mechanical design information to select construction materials suitable for a range of chemical and hydrocarbon processing plants. The volume features tables for locating the American Society for Testing and Materials (ASTM) product form specifications for construction materials that have code-allowable design stresses. It analyzes threshold values for degradation phenomena involving thermal damage.

Download or read book Materials Selection for Hydrocarbon and Chemical Plants written by Hansen and published by Routledge. This book was released on 2017-11-22 with total page 440 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describes the systematic procedure for using process and mechanical design information to select construction materials suitable for a range of chemical and hydrocarbon processing plants. The volume features tables for locating the American Society for Testing and Materials (ASTM) product form specifications for construction materials that have code-allowable design stresses. It analyzes threshold values for degradation phenomena involving thermal damage.

Download or read book Materials Selection for the Chemical Process Industries written by C. P. Dillon and published by McGraw-Hill Companies. This book was released on 1992 with total page 358 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Chemical and Process Plant a Guide to the Selection of Engineering Materials written by Lee S. Evans and published by John Wiley & Sons. This book was released on 1980 with total page 198 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Computer Aided Materials Selection During Structural Design written by Committee on Application of Expert Systems to Materials Selection During Structural Design and published by National Academies Press. This book was released on 1995-04-17 with total page 84 pages. Available in PDF, EPUB and Kindle. Book excerpt: The selection of the proper materials for a structural component is a critical activity that is governed by many, often conflicting factors. Incorporating materials expert systems into CAD/CAM operations could assist designers by suggesting potential manufacturing processes for particular products to facilitate concurrent engineering, recommending various materials for a specific part based on a given set of characteristics, or proposing possible modifications of a design if suitable materials for a particular part do not exist. This book reviews the structural design process, determines the elements, and capabilities required for a materials selection expert system to assist design engineers, and recommends the areas of expert system and materials modeling research and development required to devise a materials-specific design system.

Download or read book Selecting Engineering Materials for Chemical and Process Plant written by Lee S. Evans and published by Random House Business. This book was released on 1974 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Materials Selection and Design written by Md Abdul Maleque and published by Springer Science & Business Media. This book was released on 2013-12-11 with total page 127 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents topics on the basics of materials selection and design which will give a better understanding on the selection methods and then find suitable materials for the applications. This book draws the simple and straightforward quantitative methods followed by knowledge-based expert system approach with real and tangible case studies to show how undergraduate or post-graduate students or engineers can apply their knowledge on materials selection and design. Topics discussed in this book contain special features such as illustration, tables and tutorial questions for easy understanding. A few published books or documents are available, hence this book will be very useful for those who use (or want to use) materials selection approach without the advantages of having had comprehensive knowledge or expertise in this materials’ world.

Download or read book Chemical Engineering Design written by Gavin Towler and published by Elsevier. This book was released on 2012-01-25 with total page 1321 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chemical Engineering Design, Second Edition, deals with the application of chemical engineering principles to the design of chemical processes and equipment. Revised throughout, this edition has been specifically developed for the U.S. market. It provides the latest US codes and standards, including API, ASME and ISA design codes and ANSI standards. It contains new discussions of conceptual plant design, flowsheet development, and revamp design; extended coverage of capital cost estimation, process costing, and economics; and new chapters on equipment selection, reactor design, and solids handling processes. A rigorous pedagogy assists learning, with detailed worked examples, end of chapter exercises, plus supporting data, and Excel spreadsheet calculations, plus over 150 Patent References for downloading from the companion website. Extensive instructor resources, including 1170 lecture slides and a fully worked solutions manual are available to adopting instructors. This text is designed for chemical and biochemical engineering students (senior undergraduate year, plus appropriate for capstone design courses where taken, plus graduates) and lecturers/tutors, and professionals in industry (chemical process, biochemical, pharmaceutical, petrochemical sectors). New to this edition: Revised organization into Part I: Process Design, and Part II: Plant Design. The broad themes of Part I are flowsheet development, economic analysis, safety and environmental impact and optimization. Part II contains chapters on equipment design and selection that can be used as supplements to a lecture course or as essential references for students or practicing engineers working on design projects. New discussion of conceptual plant design, flowsheet development and revamp design Significantly increased coverage of capital cost estimation, process costing and economics New chapters on equipment selection, reactor design and solids handling processes New sections on fermentation, adsorption, membrane separations, ion exchange and chromatography Increased coverage of batch processing, food, pharmaceutical and biological processes All equipment chapters in Part II revised and updated with current information Updated throughout for latest US codes and standards, including API, ASME and ISA design codes and ANSI standards Additional worked examples and homework problems The most complete and up to date coverage of equipment selection 108 realistic commercial design projects from diverse industries A rigorous pedagogy assists learning, with detailed worked examples, end of chapter exercises, plus supporting data and Excel spreadsheet calculations plus over 150 Patent References, for downloading from the companion website Extensive instructor resources: 1170 lecture slides plus fully worked solutions manual available to adopting instructors

Download or read book Materials Selection in Mechanical Design written by M. F. Ashby and published by Pergamon. This book was released on 1992-01-01 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: New materials enable advances in engineering design. This book describes a procedure for material selection in mechanical design, allowing the most suitable materials for a given application to be identified from the full range of materials and section shapes available. A novel approach is adopted not found elsewhere. Materials are introduced through their properties; materials selection charts (a new development) capture the important features of all materials, allowing rapid retrieval of information and application of selection techniques. Merit indices, combined with charts, allow optimisation of the materials selection process. Sources of material property data are reviewed and approaches to their use are given. Material processing and its influence on the design are discussed. The book closes with chapters on aesthetics and industrial design. Case studies are developed as a method of illustrating the procedure and as a way of developing the ideas further.

Download or read book Materials Selection for Natural Fiber Composites written by Faris M Al,Oqla and published by Woodhead Publishing. This book was released on 2017-06-09 with total page 286 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials Selection for Natural Fiber Composites covers the use of various tools and techniques that can be applied for natural fiber composite selection to expand the sustainable design possibilities and support cleaner production requirements. These techniques include the analytical hierarchy process, knowledge-based system, Java based materials selection system, artificial neural network, Pugh selection method, and the digital logic technique. Information on related topics, such as materials selection and design, natural fiber composites, and materials selection for composites are discussed to provide background information to the main topic. Current developments in selecting the natural fiber composite material system, including the natural fiber composites and their constituents (fibers and polymers) is the main core of the book, with in detailed sections on various technical, environmental and economic issues to enhance both environmental indices and the industrial sustainability theme. Recent developments on the analytical hierarchy process in natural fiber composite materials selection, materials selection for natural fiber composites, and knowledge based system for natural fiber composite materials selection are also discussed. Focuses on materials selection for natural fiber composites Covers potential tools and techniques, such as analytical hierarchy process, knowledge-based systems, Java-based materials selection system, artificial neural network, the Pugh selection method and digital logic technique Contains contributions from leading experts in the field

Download or read book Process Plant Instrumentation written by Miguel J. Bagajewicz and published by CRC Press. This book was released on 2000-11-27 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the first in-depth presentation in book form of current analytical methods for optimal design, selection and evaluation of instrumentation for process plants. The presentation is clear, concise and systematic-providing process engineers with a valuable tool for improving quality, costs, safety, loss prevention, and production accounting. From Chapter 1 Introduction "Instrumentation is needed in process plants to obtain data that are essential to perform several activities. Among the most important are control, the assessment of the quality of products, production accounting... and the detection of failures related to safety. In addition, certain parameters than cannot be measured directly, such as heat exchanger, fouling or column deficiencies, are of interest. Finally, new techniques, such as on-line optimization, require the construction of reliable computer models for which the estimation of process parameters is essential. "This book concentrates on the tasks of determining the optimal set of measured variables and selecting the accuracy and reliability of the corresponding instruments. The goal is to obtain sufficiency accurate and reliable estimates of variables of interest while filtering bad data due to possible instrument malfunction. An additional goal is to observe and diagnose single and multiple process faults." From the Preface "There is a vast amount of literature devoted to the selection and good maintenance of instruments. This literature covers the selection of the right instrument for a particular range and system, but only after the desired accuracy and reliability of measurement have been established. Little has been written on how to systematically determine the right accuracy and reliability needed when selecting an instrument, much less how much redundancy is needed for a particular system. The key variables that needed estimation come from control requirements, as well as monitoring needs for safety, quality control and production accounting. These are the starting points of the design methodology. This book concentrates on determining the optimal accuracy and reliability of instruments and their location. To determine this, certain desired properties of the system of instruments are used as constraints while the cost is minimized. These properties, among others are variable observability, system reliability and precision of certain variables. "This book is not a textbook. Rather it is intended to be an organized collection of the most relevant work in this area.... It has been written with the intention of making it readable by engineers with some background in linear algebra, mathematical optimization and graph theory. It is organized so that the complexity of the sensor network design is addressed step by step." The information in this new book serves the needs of chemical and other process engineers involved in instrumentation and control, maintenance, plant operations, process design, process development, quality control, safety, and loss prevention. Illustrations and Tables The text is supplemented with more than 100 flow charts, diagrams and other schematics that illustrate procedures, systems and instrumentation. More than 70 tables provide useful reference data. The Author Dr. Miguel J. Bagajewicz brings to this new book his extensive experience in design, data management, teaching and writing in the area of process engineering. He received his M.S. and Ph.D. in Chemical Engineering from the California Institute of Technology. He is presently Associate Professor, School of Chemical Engineering and Materials Science, and Director, Center for Engineering Optimization at the University of Oklahoma. He is the author or co-author of more than 100 journal articles, conference presentations, and reports, and the author of articles on data reconciliation and sensor location in the Instrument Engineers' Handbook, fourth edition. He is a member of the American Institute of Chemical Engineers (AIChE), and on the executive committee of the Central Oklahoma Chapter.

Download or read book Materials and Process Selection for Engineering Design written by Mahmoud M. Farag and published by CRC Press. This book was released on 2020-12-30 with total page 531 pages. Available in PDF, EPUB and Kindle. Book excerpt: Introducing a new engineering product or changing an existing model involves developing designs, reaching economic decisions, selecting materials, choosing manufacturing processes, and assessing environmental impact. These activities are interdependent and should not be performed in isolation from each other. This is because the materials and processes used in making a product can have a major influence on its design, cost, and performance in service. This Fourth Edition of the best-selling Materials and Process Selection for Engineering Design takes all of this into account and has been comprehensively revised to reflect the many advances in the fields of materials and manufacturing, including: Increasing use of additive manufacturing technology, especially in biomedical, aerospace and automotive applications Emphasizing the environmental impact of engineering products, recycling, and increasing use of biodegradable polymers and composites Analyzing further into weight reduction of products through design changes as well as material and process selection, especially in manufacturing products such as electric cars Discussing new methods for solving multi-criteria decision-making problems, including multi-component material selection as well as concurrent and geometry-dependent selection of materials and joining technology Increasing use of MATLAB by engineering students in solving problems This textbook features the following pedagogical tools: New and updated practical case studies from industry A variety of suggested topics and background information for in-class group work Ideas and background information for reflection papers so readers can think critically about the material they have read, give their interpretation of the issues under discussion and the lessons learned, and then propose a way forward Open-book exercises and questions at the end of each chapter where readers are evaluated on how they use the material, rather than how well they recall it, in addition to the traditional review questions Includes a solutions manual and PowerPoint lecture materials for adopting professors Aimed at students in mechanical, manufacturing, and materials engineering, as well as professionals in these fields, this book provides the practical know-how in order to choose the right materials and processes for development of new or enhanced products.

Download or read book Materials and Design written by Michael F. Ashby and published by Butterworth-Heinemann. This book was released on 2010 with total page 342 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials are the stuff of design. From the very beginning of human history, materials have been taken from the natural world and shaped, modified, and adapted for everything from primitive tools to modern electronics. This renowned book by noted materials engineering author Mike Ashby and Industrial designer, Kara Johnson, explores the role of materials and materials processing in product design, with a particular emphasis on creating both desired aesthetics and functionality. The new edition will feature even more of the highly useful "materials profiles," that give critical design, processing, performance and applications criteria for each material in question. The reader will find information ranging from the generic and commercial names of each material, its physical and mechanical properties, its chemical properties, its common uses, how it is typically made and processed, and even its average price. And with improved photographs and drawings, the reader will be taken even more closely to the way real design is done by real designers, selecting the optimum materials for a successful product. * The best guide ever published on the on the role of materials, past and present, in product development, by noted materials authority Mike Ashby and professional designer Kara Johnson--now with even better photos and drawings on the Design Process * Significant new section on the use of re-cycled materials in products, and the importance of sustainable design for manufactured goods and services * Enhanced materials profiles, with addition of new materials types like nanomaterials, advanced plastics and bio-based materials

Download or read book Selection and Use of Engineering Materials written by J A Charles and published by Elsevier. This book was released on 2013-10-22 with total page 349 pages. Available in PDF, EPUB and Kindle. Book excerpt: Selection and Use of Engineering Materials, Second Edition covers the substantial development in the selection and application of materials and of associated materials. This book is organized into four parts encompassing 20 chapters that also consider the advances in materials databases and computer programs. The first part deals with the motivation, cost basis, service requirements, failure analysis, specifications, and quality control of engineering materials. The second part describes the mechanical properties of these materials, including static strength, toughness, stiffness, fatigue, creep, and temperature resistance. The third part examines the selection requirements for surface durability, such as corrosion and wear resistance. This part also explores the relationship between materials selection and materials processing, as well as the formalization of selection procedures. The fourth part provides some case studies in materials selection. This book will prove useful to materials scientists and practicing engineers.

Download or read book Process Plant Layout written by Sean Moran and published by Butterworth-Heinemann. This book was released on 2016-11-16 with total page 756 pages. Available in PDF, EPUB and Kindle. Book excerpt: Process Plant Layout, Second Edition, explains the methodologies used by professional designers to layout process equipment and pipework, plots, plants, sites, and their corresponding environmental features in a safe, economical way. It is supported with tables of separation distances, rules of thumb, and codes of practice and standards. The book includes more than seventy-five case studies on what can go wrong when layout is not properly considered. Sean Moran has thoroughly rewritten and re-illustrated this book to reflect advances in technology and best practices, for example, changes in how designers balance layout density with cost, operability, and safety considerations. The content covers the ‘why’ underlying process design company guidelines, providing a firm foundation for career growth for process design engineers. It is ideal for process plant designers in contracting, consultancy, and for operating companies at all stages of their careers, and is also of importance for operations and maintenance staff involved with a new build, guiding them through plot plan reviews. Based on interviews with over 200 professional process plant designers Explains multiple plant layout methodologies used by professional process engineers, piping engineers, and process architects Includes advice on how to choose and use the latest CAD tools for plant layout Ensures that all methodologies integrate to comply with worldwide risk management legislation

Download or read book Guidelines for Vapor Release Mitigation written by Richard W. Prugh and published by John Wiley & Sons. This book was released on 2010-09-16 with total page 172 pages. Available in PDF, EPUB and Kindle. Book excerpt: Guidelines for Vapor Release Mitigation is a survey of current industrial practice for controlling accidental releases of hazardous vapors and preventing their escape from the source area.